American Standard Estate 7722.101 Series User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
Congratulations on purchasing your American Standard faucet
with Speed Connect drain, a feature found only on American
Standard faucets.
Speed Connect®Drain*
• Fewer parts, installs in less time.
• Never needs adjustment.
• Guaranteed to seal properly the rst time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965729 Rev. 1.0 (3/16)
INSTALL FAUCET
ESTATE®
SINGLE LEVER MONOBLOCK LAVATORY
WITH SPEED CONNECT®DRAIN
INSTALLATION
INSTRUCTIONS
7722.101
Adjustable WrenchScrewdriver Channel Locks
Certied to comply with ANSI A112.18.1M
CAUTION Turn off hot and cold water
supplies before beginning.
1
22
3
HOLES
(FAUCET
BASE) HOLES
(FAUCET
BASE)
PUTTY
IF REQUIRED
Fig. A. Fig. B.
5
2
HOLES
(FAUCET
BASE)
Fig. C.
6
8
7
4
7A
6
8
7
54
7A
6
8
7
54
7A
9
1
10
Fig. A.
• Installation with ESCUTCHEON PLATE: Align PINS (1) with holes in FAUCET BASE (2). Fig. A. Apply a light bead of
plumbers putty to underside of ESCUTCHEON (3) if mounting surface is uneven. Place ESCUTCHEON (3) onto sink or
mounting surface. Fig. A. Feed FAUCET SUPPLIES (4), MOUNTING SHANK (5) and DRAIN CABLE ASSEMBLY (6)
through ESCUTCHEON with PUTTY PLATE (3) and mounting hole of lavatory or mounting surface. Fig. A.
Fig. B.
• Installation with SMALL ESCUTCHEON (10): Align PINS (1) with holes in FAUCET BASE (2). Fig. B.
• Feed FAUCET SUPPLIES (4), MOUNTING SHANK (5) and DRAIN CABLE ASSEMBLY (6) through mounting hole of lavatory or
mounting surface. Fig. B.
Fig.C.
• Seat SEAL (9) under the FAUCET BASE (2) when escutcheon is not used.
• Feed FAUCET SUPPLIES (4), MOUNTING SHANK (5) and DRAIN CABLE ASSEMBLY (6) through mounting hole of lavatory or
mounting surface. Fig. C.
• Fig. A., B. & C. Assemble RUBBER WASHER (7), FRICTION WASHER (7A) and thread LOCKNUT (8) onto MOUNTING
SHANK (5) from underside of sink or mounting surface. Fig. B.
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (8) to complete faucet mounting. Fig. A., B. & C.

- 2 -
2
M965729 Rev. 1.0 (3/16)
3REMOVE FLANGE
• Remove CLEAR PLASTIC COVER (1).
• Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
• Tighten TAIL PIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
POP-UP DRAIN
• Thread FLANGE (1) counter-clockwise and
remove FLANGE (1) and FOAM GASKET (2)
from drain body. Fig. A.
• Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3).Fig. B.
4INSTALL DRAIN FROM
BELOW FIXTURE
• From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
• Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) rmly.
2
3
1
Fig. A. Fig. B.
DRAIN
BODY
4
2
3
4
Fig. B.
1
Fig. A.
6FLANGE GASKET AND POP-UP KNOB
• Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
• POP-UP KNOB (1) must be fully down. Fig. B.
2
DRAIN
OUTLET
1
3
4
REAR OF SINK 5TIGHTEN LOCKNUT
• Tighten LOCKNUT (1) rmly with Adjustable
Wrench or Channel Locks.
1
1
Fig. A.
WHITE FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
DOWN
Fig. B.

- 3 -
8
9
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
• Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tail piece on pop-up drain is 1-1/4"
O.D. Fig. B.
• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
ATTACH CABLE CONNECTOR
7
M965729 Rev. 1.0 (3/16)
Fig. A.
2
1
Fig. B.
1-1/4" O.D.
2
1
1
APPROX. 20"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Band) and right
supply to COLD (2) wall supply.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Connect 1-1/4" O.D. tail piece on POP-UP DRAIN to
waste outlet.

M965729 Rev. 1.0 (3/16)
11
12
• With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3).
SERVICE
TEST INSTALLED FITTING
10
2
4
5
2
“P” TRAP
3
6
1OFF
ON
COLD
HOT
WASTE
OUTLET
• Operate POP-UP KNOB (4) and ll lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in Sink. If DRAIN STOPPER (5)
does not seal properly, please refer to Troubleshooting
section in these instructions.
• Release POP-UP KNOB (4) down and check all drain
connections and “P” trap for leaks. Tighten
if necessary.
CHECK DRAIN CONNECTIONS
• To remove or replace cartridge:
- Turn valve to OFF position.
- Remove the INDEX BUTTON (1).
- Loosen SET SCREW (2). Pull off HANDLE (3).
- Pull off CAP (4).
- Remove CARTRIDGE SCREWS (5).
- Pull out CARTRIDGE (6).
- Inspect CARTRIDGE (6) and O-RING (7) for debris and clean
if necessary.
- Clean MANIFOLD (8) and rinse clean.
- Reinstall CARTRIDGE (6) and O-RING (7) onto MANIFOLD (8).
- Reinstall CARTRIDGE SCREWS (5), CAP (4) and HANDLE
ASSEMBLY (3).
• If spout drips, operate handles several times from OFF to ON
position. Do not force.
5
6
7
4
3
2
1
2.5mm
HEX KEY
8
CAUTION Turn off hot and cold water
supplies before beginning.
- 4 -
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.

M965729 Rev. 1.0 (3/16)
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Speed Connect®Drain
Troubleshooting Guide
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
CABLE ADJUSTMENT PROCEDURE
CAM
CAM CAP
Fig. B.Fig. A.
2
1
RE-ATTACH
DISCONNECT
DOWN
Fig. C.
LIFT-KNOB
STOPPER
REMOVE
CAM
Fig. E.Fig. D.
REMOVE
CAM CAP
Fig. F.
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
• Use ngers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.
STOPPER REMOVAL PROCEDURE
- 5 -

- 6 - M965729 Rev. 1.0 (3/16)
Locked Mode
(Vandal Proof)
LOOP TOWARD
REAR OF SINK
Fig. G.
LOGO
DRAIN
Unlocked Mode
LOOP TOWARD
FRONT OF SINK
180˚
LOGO
DRAIN
Fig. H.
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice that the
Loop is on one side of the Stopper. Fig. G.
• T o install the stopper in “Locked” mode, insert the Stopper into the Drain so
that the Plastic Loop is facing toward the rear of the Sink and the American
Standard logo is facing front. Rotate Stopper slightly if necessary so that the
Stopper slides all the way down. Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure
it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If
the Cam Cap does not “snap” into place, then rotate the Cam to make sure
it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in Troubling
Shooting Guide to complete installation. Stopper will be in “Locked” mode
and not be removable.
Unlocked Mode:
• Look at the Plastic Loop at the bottom of the Stopper and notice that the
Loop is on one side of the Stopper. Fig. H.
• T o install the stopper in “Unlocked” mode, insert the Stopper into the Drain
so that the Plastic Loop is facing toward the front of the Sink and the American
Standard logo is facing rear. Rotate Stopper slightly if necessary so that the
Stopper slides all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it
is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the
Cam Cap does not “snap” into place, then rotate the Cam to make sure it is
fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Trouble-shooting Guide” to complete installation. Stopper will be in
“Unlocked” mode and removable.

- 7 - M965729 Rev. 1.0 (3/16)
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M970058-YYY0A
HANDLE KIT
M951483-0070A
CARTRIDGE
M970004-0070A
AERATOR (1.2 GPM)
M970059-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M918511-0070A
CARTRIDGE SCREWS
M907315-YYY0A
COVER
M970061-0070A
MOUNTING KIT
M970056-YYY0A
POP-UP ROD
ASSEMBLY
M970060-YYY0A
ESCUTCHEON AND
SEAL
M962430-0070A
CAM ASSEMBLY
M952430-0070A
CABLE ASSEMBLY
M962457-YYY0A
FLANGE
ASSEMBLY
M962458-0070A
DRAIN MOUNTING KIT
A919661-0020A
TAILPIECE
M922872-0070A
CAM SEAT INSERT
M913207-0070A
TAILPIECE INSERT
M962544-YYY0A
STOPPER
ASSEMBLY
M952425-YYY0A
DRAIN ASSEMBLY
ESTATE®
SINGLE LEVER
MONOBLOCK LAVATORY
WITH SPEED CONNECT®DRAIN
MODEL NUMBER
7722.101
Replace the “YYY” with
appropriate finish code
CHROME 002
SATIN NICKEL 295
LEGACY BRONZE 278
POLISHED NICKEL 013