American Standard 403 User manual

SAVE FOR FUTURE USE
7301354-100 Rev. B
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2009
NOTE: Pictures may not exactly define contour of china and components.
0641 BOULEVARD
0403 TROPIC PETITE
0404 TROPIC GRANDE
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard-us.com
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
In Canada:
AS Canada ULC
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
www.americanstandard.ca
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com/mx
Adjustable Wrench
Channel Lock Pliers Regular Screwdriver
Recommended Tools & Materials
Phillips Screwdriver
Pipe Wrench
Putty Knife
Drill Saber Saw
Basin Wrench
Plumbers' Putty or
Caulking
Tubing Cutter
Tape
Measure
Hacksaw
Level
This lavatory can be installed 4 different ways. Please follow the instructions for your installation method.
1. PEDESTAL 2. WALL-HUNG ON FURNITURE 3. ABOVE COUNTER 4. DROP-IN
* not recommended for 0404 * not recommended for 0404

27301354-100 Rev. B
1-E
1-7/8"
ANCHOR SCREW INSTALLATION
Use lag bolts to secure
lavatory as illustrated.
LAG BOLT INSTALLATION
Anchor
Screw
Washer
Lavatory
Nut
Lag
Bolt
Washer
Lavatory
Lavatory
Steel
Hanger
IMPORTANT: Final assembly of nut and washer or lag bolt method shown for reference only.
1-F
A
1-I
Shut-Off
Valves
Rear
View
Pedestal
Screws
1-G
B
C
Install pedestal screws.
Securely tighten lavatory
anchor nuts or lag bolts.
Note: Space constraints
may dictate method of
fastening pedestal to floor.
1. Pedestal installation
1-D
Remove lavatory and
pedestal from installed
position. Drill pilot holes for
lavatory and pedestal
anchor screws or lag bolts.
Note: Some models are supplied with lag bolts, anchor screws,
or steel hangers for lavatory installations only. Other models and
all pedestals are not provided with mounting hardware. Various
pedestal screw sizes and types are available to the installer at
local hardware outlets.
1-A
Provide suitable reinforcement
behind finished wall for lavatory
mounting screws.
*Determine horizontal center line
location of support from fixture.
NOTE: If replacing an existing sink
be certain to shut off water supply
before removing old sink.
C/L of 2X6
Support
Finished
Floor
*
1-C Mark lavatory and pedestal screw locations through
the mounting holes.
1-B Top of Pedestal
For example only
Place lavatory and pedestal into installed position. Level and
square the lavatory and pedestal assembly. Use one or more
bumper cushions to level and cushion lavatory slab to pedestal. 1-H
Secure lavatory to wall as
shown in 1E. Install washers
and hand tighten nuts or lag
bolts. Level and square the
unit. Connect hot and cold
supply lines to the shut-off
valves. Tighten trap joints for
watertight assembly.
Following manufacturer's
instructions, install faucet and
drain assembly (not included). Be
certain to apply a bead of sealing
putty on the underside of the drain
(area "A") in order to ensure a
watertight seal between the
lavatory and drain. Remove
excess putty after installing
drain on lavatory.
Return the fitted lavatory to the
installed position. Connect trap to
drain assembly hand tight to check
alignment. It may be necessary to
cut off part of the tailpiece (area
"B") or part of the horizontal leg of
the trap (area "C").
Approx. Bumper locations to
raise the lavatory slab left side.
Install lavatory anchor screws
leaving 1-7/8" threaded end
exposed as illustrated.

37301354-100 Rev. B
B
C
2-G
Connect trap to drain assembly hand tight to
check alignment. It may be necessary to cut
off part of the tailpiece (area “B”) or part of the
horizontal leg of the trap (area “C”). Secure
joints for watertight assembly.
2-F
Connect supply line to faucet (finger tight) and
carefully bend tubes to engage with the
supply shut-off valves. Tighten connections at
faucet and shut-off valves for secure seal.
Shut-Off Valves
2. Wall-hung on furniture
2-C Vanity Installation:
• Place the sink temporarily on the vanity to
check for alignment and clearance
Mounting on Furniture:
Assemble vanity as per instructions.
2-A
2-D
After checking fit and alignment, turn sink upside down
and apply a generous portion of silicone adhesive
around the under side of the rim near the edge. Place
sink in position. Wipe off excess adhesive.
Mount the faucet and drain assembly (not included) on
the sink following the manufacturer’s instructions. Be
certain to apply a bead of sealing putty on the
underside of the drain (Part “A”) in order to ensure a
watertight seal between the sink and drain. Remove
excess putty after installing drain on sink.
2-B
A
2-E
Use the mounting holes on the rear of the lavatory
to secure the sink to the wall.

47301354-100 Rev. B
Countertop Installation:
Using the template provided, locate the position of the sink
on the countertop. Provide proper clearance under the
countertop for the faucet supply lines, drain assembly and
the structural parts of the cabinet.
NOTE: If replacing an existing sink be certain to shut off
water supply before removing old sink.
3-A
4-A
Countertop Installation:
• Place the sink temporarily into the template
• Check for alignment and clearance
• Mark the sink and countertop in several
places as a guide for the installation location.
3-D
4-D
Connect supply line to faucet
(finger tight) and carefully
bend tubes to engage with
the supply shut-off valves.
Tighten connections at faucet
and shut-off valves for
secure seal.
Shut-Off Valves
3-G
4-G
Use the mounting holes on the rear of the lavatory to
secure the sink to the wall.
3-F
4-F
B
C
Connect trap to drain assembly
hand tight to check alignment. It
may be necessary to cut off part
of the tailpiece (area “B”) or part
of the horizontal leg of the trap
(area “C”). Secure joints for
watertight assembly.
3-H
4-H
After checking fit and alignment, turn sink upside down and
apply a generous portion of silicone adhesive around the
under side of the rim near the edge. Place sink in position.
Wipe off excess adhesive.
3-E
4-E
Mount the faucet and
drain assembly (not
included) on the sink
following the
manufacturer’s
instructions. Be certain
to apply a bead of
sealing putty on the
underside of the drain
(Part “A”) in order to
ensure a watertight seal
between the sink and
drain. Remove excess
putty after installing
drain on sink.
A
3-C
4-C
Drill a clearance hole inside the perimeter line of the
template for countertop installation.
Cut opening around the perimeter of the template.
Perimeter
of
template
Perimeter of
template
3-B
4-B
3. Above Counter OR
4. Drop-in
Part #
REPAIR
PARTS
LIST
Description
047523-0070A Wall mounting kit
** BACK OF LAVATORY IS UNGLAZED **
The lavatory must be installed flush with wall.