American Standard Colony Soft T975.400 User manual

C
5
M968757D
Certified to comply with ANSI A112.18.1
1SPOUT INSTALLATION
U.S. Patent No. D403,750
REMOVE ALL
BURRS AND
BEVEL
TEMPLATE FOR
SPOUT ROLL
PIN LOCATION
3/16" DIA.
HOLE
20.5mm
(13/16")
1"- 2"
FRONT
Complete FINISHED DECK (A) before trim installation.
Turn off the water supplies.
Remove the GUARDS (1) from the VALVE BODIES (2). Remove the
SPOUT GUARD (3) and 1/4" PLUG (4) from the SPOUT SHANK (5).
The SPOUT SHANK (6) height should be 1" to 2" above the FINISHED
DECK (A). Cut the SPOUT SHANK (5) if necessary. Remove all burrs
and bevel the end of the shank. Failure to do so may damage
the SPOUT O-ring during installation and cause water leakage.
Drill a 3/16" HOLE (C) in the finished deck. See TEMPLATE for location.
Lubricate the SPOUT O-RING (6).
Remove the PLUG BUTTON (7) from the SPOUT (8).
Position the RUBBER RING (9) in the GROOVE (B) in the base of the SPOUT (8).
Push the SPOUT (8) down onto the SPOUT SHANK (5) and align the SPOUT PIN (12)
with the 3/16" DRILLED HOLE (C) in the FINISHED DECK (A).
Tighten the SET SCREW (10) securely with the 5mm HEX KEY (11).
Insert the PLUG BUTTON (7) into the SPOUT (8).
A
43
1
2
5
10
12
12
7
11
8
5
A
C
9
6
B
Gracias por preferir American Standard…. El punto de referencia de la más fina calidad por más de
100 años. Para asegurar que su instalación se efectue de la mejor forma favor de leer estas
instrucciones cuidadosamente antes de empezar.
Instrucciones de Instalacion
Nous vous remercions d'avoir choisi American Standard... synonyme de qualité
supérieure depuis plus de 100 ans. Pour s'assurer d'une installation sans
inconvénients, veuillez lire attentivement ces instructions avant de commencer.
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Instructions d'installation
Installation Instructions
CAUTION Turn off hot and cold water
supplies before beginning.
INSTALLER
LE ROBINET ATTENTION
ADVERTENCIA: Cierre la tuberia de la ali mentación
del agua caliente y fría antes de comenzar lainstalación
Fermer l'alimentation
d'eau chaude et froideavant de
commencer.
ARMADO
DE LA LLAVE
Complete la CUBIERTA TERMINADA (A) antes de instalar el juego decorativo.
Cierre el suministro de agua.
Quite los PROTECTORES (1) del CUERPO DE LAS VÁLVULAS (2). Quite el PROTECTOR
DEL GRIFO (3) y el TAPÓN (4) de 1/4 de pulgada (6,4 mm) del POSTE DEL GRIFO (5).
La altura del POSTE DEL GRIFO (5) debe ser de 1 a 2 pulgadas (25 a 51 mm) sobre
la CUBIERTA TERMINADA (A). Corte el POSTE DEL GRIFO (5) si es necesario. Quite todas
las rebabas y bisele el extremo del poste. Si no lo hace, puede dañar la junta tórica
del GRIFO durante la instalación y ocasionar fugas.
Taladre un AGUJERO (C) de 3/16 de pulgada (4,8 mm) en la cubierta terminada.
Consulte la PLANTILLA para conocer la ubicación.
PLANTILLA DE UBICACIÓN DEL
PASADOR DE GIRO DEL GRIFO
Lubrique las JUNTAS TÓRICAS DEL GRIFO (6).
Quite el BOTÓN OBTURADOR (7) del GRIFO (8).
Coloque el ANILLO DE CAUCHO (9) en la RANURA (B) de la base del GRIFO (8).
Empuje el GRIFO (8) hacia abajo sobre el POSTE DEL GRIFO (5) y alinee el PASADOR DEL
GRIFO (12) con el AGUJERO PERFORADO (C) de 3/16 de pulgada (4,8 mm) en la CUBIERTA TERMINADA (A).
Apriete firmemente el TORNILLO DE SUJECIÓN (10) utilizando la LLAVE HEXAGONAL (11) de 5 mm.
Inserte el BOTÓN OBTURADOR (7) en el GRIFO (8).
Terminer la PLAGE DE L’ÉVIER FINIE (A) avant d’installer les garnitures.
Couper l’alimentation d’eau.
Retirer les PROTECTEURS (1) des CORPS DE VANNE (2). Retirer
le PROTECTEUR DU BEC (3) et le TAMPON (4) de 6 mm de la TIGE
DU BEC (5).
La TIGE DU BEC (6) devrait dépasser la PLAGE DE L’ÉVIER
FINIE (A) d’une hauteur de 2,5 à5,0 cm. Couper la TIGE DU
BEC (5) si nécessaire. Retirer toutes les barbures et niveler
l’extrémitéde la tige. Sinon, le joint torique du BEC risque
d’être endommagédurant l’installation et causer des fuites d’eau.
Percer un TROU (C) de 5 mm dans la plage de l’évier finie. Se
reporter au GUIDE pour connaître l’emplacement.
Lubrifier le JOINT TORIQUE DU BEC (6) et
Retirer la CAPSULE DU TAMPON (7) du BEC (8).
Placer la BAGUE DE CAOUTCHOUC (9) dans la RAINURE (8) située dans la base du BEC (8).
Pousser le BEC (8) vers le bas dans la TIGE DU BEC (5) et aligner la GOUPILLE DU BEC (12) avec le
TROU PERCÉ(C) de 5 mm situédans la PLAGE DE L’ÉVIER FINIE (A).
Serrer la VIS DE RÉGLAGE (10) fermement au moyen d’une CLÉHEXAGONALE (11) de 5 mm.
Insérer la CAPSULE DU TAMPON (7) dans le BEC (8).
GUIDE POUR L’EMPLACEMENT DE LA
GOUPILLE CYLINDRIQUE DU BEC.
COLONY SOFT DECK MOUNT TRIM KIT
TROUSSE DE GARNITURE POUR MONTAGE SUR
PLAGE D’ÉVIER COLONY
JUEGO DECORATIVO PARA CUBIERTA COLONY T975.400/400BP
T975.500/500BP
H
C

M968757D
2VALVE TRIM
Fit ESCUTCHEON SEALS (1) into underside of VALVE ESCUTCHEONS (2).
Thread the VALVE ESCUTCHEONS (2) into the VALVE BODIES (3). Align the HANDLE
STEM (4) with the SLEEVE (5) as necessary. Thread the VALVE ESCUTCHEON (2) into
the BODIES (3) until the ESCUTCHEON (2) contacts the finished deck.
2
1
3
5
4
4
1
2
3
5
3INSTALL LEVER HANDLE TRIM
Turn HANDLE STEM (1) to "OFF" position.
Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).
Install the ADAPTER SCREW (3) and tighten securely.
Position LEVER HANDLE (4) and place on ADAPTER (2). Install the
HANDLE SCREW (5) and tighten securely.
Coloque los SELLOS DE LOS CHAPETONES (1) en la parte inferior de los CHAPETONES
DE LAS VÁLVULAS (2).
Enrosque los CHAPETONES DE LAS VÁLVULAS (2) en los CUERPOS DE LAS VÁLVULAS (3).
Alinee el TALLO DE LA LLAVE (4) con el MANGUITO (5) si es necesario. Enrosque el
CHAPETÓN DE LA VÁLVULA (2) en el CUERPO (3) hasta que el CHAPETÓN (2) haga contacto con la cubierta terminada.
Gire el TALLO DE LA LLAVE (1) a la posición de cierre.
Coloque el ADAPTADOR DE LA LLAVE (2) en el TALLO DE LA LLAVE (1). Instale el TORNILLO
DEL ADAPTADOR (3) y apriételo firmemente.
Ajuste la posición de la LLAVE DE PALANCA (4) y colóquela sobre el ADAPTADOR (2).
Coloque el TORNILLO DE LA LLAVE (5) y apriételo firmemente.
Placer la TIGE DE LA POIGNÉE (1) en position «FERMÉE ».
Placer l’ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1). Installer la VIS
D’ADAPTATION (3) et serrer fermement.
Mettre la MANETTE ÀVOLANT (4) en position et la placer sur l’ADAPTATEUR (2).
Installer la VIS POUR MANETTE (5) et serrer fermement.
Insérer les JOINTS DE ROSACE (1) dans la face inférieure des JOINTS DE VANNE (2).
Enfiler les JOINTS DE VANNE (2) dans les CORPS DE VANNE (3). Aligner la TIGE DE LA POIGNÉE (4) avec le MANCHON (5),
au besoin. Enfiler le JOINT DE VANNE (2) dans les CORPS (3) jusqu’à ce que le JOINT (2) entre en contact avec la plage de l’évier finie.
INSTALACIÓN DE LA MANIJA
INSTALLATION DE LA POIGNÉE
JUEGO DE ESCUDETE
KIT D'ÉCUSSON
4
Turn HANDLE STEM (1) to "OFF" position.
Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).
Position ACRYLIC HANDLE (3) and install on ADAPTER (2).
Install the HANDLE SCREW (4) and tighten securely.
Push in INDEX BUTTON (5). (Hot-left side , Cold-Right side)
Placer la TIGE DE LA POIGNÉE (1) en position «FERMÉE ».
Gire el TALLO DE LA LLAVE (1) a la posición de cierre
INSTALL ACRYLIC HANDLE TRIM
INSTALE LAS MANIJAS ACRÍLICAS
Ubique la MANIJA ACRÍLICA (3) en el ADAPTADOR DE PIE DE LA MANIJA (2).
Instale el TORNILLO DE MANIJA (4) y ajuste bien.
Coloque el ADAPTADOR DE PIE DE LA MANIJA (2) en el PIE DE LA MANIJA (1).
INSTALLER LES POIGNÉES EN ACRYLIQUE
Placer la POIGNÉE EN ACRYLIQUE (3) sur la l’ADAPTATEUR DE POIGNÉE (2).
Installer les VIS POUR LES POIGNÉES (4) et bien serrer.
Placer l’ADAPTATEUR DE POIGNÉE (2) sur la TIGE DE LA POIGNÉE (1).
Presione sobre BOTÓN ÍNDICE (5).
Insérer le BOUTON INDICATEUR (5).
4
3
5
H
2
1

M968757D
TESTER L'INSTALLATION DU ROBINET
Operate both handles to flush water lines thoroughly.
Replace STREAM STRAIGHTENER (1).
Quite el REGULADOR DEL CHORRO DE AGUA (1). Cierre las llaves, abra el
suministro de agua y revise las conexiones para asegurar que no tengan fugas.
Girar ambos manerales para dejar fluir el agua de las tuberias.
Accionar la varilla del drenaje y cheque contra fugas. Reinstalar el
REGULADOR DEL CHORRO DE AGUA (1).
Remove STREAM STRAIGHTENER (1). With handles in OFF position,
turn on water supplies and check all connections for leaks.
PRUEBA DE LA LLAVE INSTALADA
TEST INSTALLED FAUCET
Ouvrir les deux POIGNÉES, rincer les conduits d'eau abondamment.
Opérer la TIGE DE LEVAGE et vérifier si le VIDAGE fuit. Replacer le DISPOSITIF
DE REDRESSEMENT DU JET (1).
5
Retirer le DISPOSITIF DE REDRESSEMENT DU JET (1). Tout en gardant les
poignées en position FERMÉE, mettre l’alimentation d’eau en marche
et vérifier tous les raccords pour s’assurer qu’il n’y ait pas de fuites.
©American Standard Inc. 2001
1
2
6
La saletépeut s'accumuler dans l'aérateur et
causer un débit d'eau plus faible ou inégal.
Enlever l'aérateur et rincer.
Si le bec coule, ouvrir et fermer les poignées
plusieurs fois de suite. Ne pas forcer. Tourner
seulement à90˚.
El aireador tal vez acumule suciedad,
causando un flujo no uniforme del agua
Remover el aireador, enjuagar y limpiar.
Si la salida gotea gire los manerales
varias veces desde la posición de cer-
rado a la posición de abierto. No force
los manerales, solamente girelos a 90
grados.
Stream straightener may accumulate
dirt causing distorted and reduced
water flow. Remove aerator and rinse
clean.
If spout drips, operate handles
several times from OFF to ON position.
Do not force-handles turn only 90˚.
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH
CLEAR WATER. DRY WITH A SOFT COTTON
FLANNEL CLOTH.
INSTRUCCIONES DE CUIDADO
DEL PRODUCTO:
LIMPIE EL PRODUCTO CON AGUA LIMPIA
Y SÉQUELO CON UNA TELA SUAVE DE
FRANELA DE ALGODÓN.
INSTRUCTIONS POUR L'ENTRETIEN
FAIRE : SIMPLEMENT RINCER LE PRODUIT AVEC DE
L'EAU CLAIRE JUSQU'ÀCE QU'IL SOIT PROPRE SÉCHER
AVEC UN LINGE DE FLANELLE DE COTON DOUX.
If faucet drips proceed as
follows: Si le robinet coule, suivre les instructions
suivantes:
Si la llave gotea proceda como
sigue:
DO NOT: DO NOT CLEAN THE PRODUCT WITH
SOAPS, ACID, POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH A COARSE
SURFACE.
NO LIMPIE EL PRODUCTO CON JABÓN,
ÁCIDOS, PULIDORES, ABRASIVOS,
LIMPIADORES FUERTES O TELAS ÁSPERAS.
NE PAS FAIRE : NE PAS NETTOYER LE PRODUIT AVEC
DES SAVONS, DE L'ACIDE, DU POLISH, DES ABRASIFS,
DES NETTOYANTS AGRESSIFS OU UN LINGE ÀTEXTURE
RUGUEUSE.
Product names listed herein are trademarks of American Standard Inc.
ASSISTANCE TÉLÉPHONIQUENUMBERO DE EMERGENCIAHOTLINE FOR HELP
CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
For toll-free information and answers to your questions, call:
Para información y respuestas a sus preguntas, llame sin costo al:
Pour information et réponses àvos questions, composer sans frais:
1 800 442-1902
Weekdays Días laborales de las Sur semaine:
8:00 to 8:00 p.m. EST
Weekdays Días laborales de las Sur semaine:
8:00 to 7:00 p.m. EST

M968757D
M918021-0070A
ADAPTER
ADAPTAR
APPROPRIER
M918504-0070A
SCREW
TORNILLO
VIS
M916803-YYY0A
METAL LEVER HANDLE
MANIJA METÁLICA
POIGNÉE MÉTALLIQUE PLEINE
M918075-0070A
HANDLE SCREW
TORNILLO DE LA MANIJA
VIS DE LA POIGNÉE
COLONY SOFT DECK MOUNT TRIM KIT
028678-0070A
STREAM STRAIGHTENER
REGULADOR DE CHORRO DE AGUA
REDRESSEUR DE JET
M961640-YYY0A
SPOUT
BOQUILLA
BEC
CHROME, CROMO, CHROME
POLISHED BRASS, BRONCE PULIDO, LAITON POLI 002 099
Replace the "YYY" with appropriate finish code
Reemplace las letras "YYY" por el código de acabado
Remplacer le "YYY" par le code de finition approprié
M961460-0020A
VALVE ESCUTCHEON KIT
JUEGO DE ESCUDETE
KIT D'ÉCUSSON
TROUSSE DE GARNITURE POUR MONTAGE SUR
PLAGE D’ÉVIER COLONY
JUEGO DECORATIVO PARA CUBIERTA COLONY
MODEL NUMBER
NÚMERO DE MODELO
NUMÉRO DE MODÈLE
M908423-0070A
ACRYLIC HANDLE
Maneral Acrilico
POIGNÉE ACRYLIQUE
M918504-0070A
SCREW
Tornillo
VIS
M950144-0070A
INDEX, BUTTON, HOT
Boton Indicador de
Agua Caliente
BOUTON INDEX, CHAUD
M950143-0070A
INDEX, BUTTON, COLD
Boton Indicador de
Agua Fria
BOUTON INDEX, FROID
H
T975.500BP
T975.500
T975.400BP
T975.400
M961461-YYY0A
BUTTON AND SCREW
BOTON Y TORNILLO
BOUTON ET VIS

COLONY DIVERTER & PERSONAL
SHOWER TRIM KIT
DECK MOUNT
TUB FILLERS
Installation
Instructions
M968356
T990 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
FINISHED
DECK
HANDLE
STEM
SLEEVE
ESCUTCHEON
SEAL
VALVE
ESCUTCHEON
1INSTALL DIVERTER VALVE TRIM
REMOVE THE DIVERTER GUARD.
Place the ESCUTCHEON SEAL over the DIVERTER BODY.
Thread the VALVE ESCUTCHEON into the DIVERTER BODY.
Align the HANDLE STEM with the SLEEVE as necessary.
Thread the VALVE ESCUTCHEON into the BODY until the
ESCUTCHEON contacts the finished deck.
DIVERTER
GUARD
SEAL
WASHER
SHOWER
HOSE
RUBBER RING
SHOWER
ESCUTCHEON
HOLDER
SEAL WASHER
HAND SHOWER
VALVE
ESCUTCHEON
HANDLE
SCREW
HANDLE
INDEX
BUTTON

Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 2000
2
3
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Unscrew the HOLDER from the SHOWER ESCUTCHEON. Slip the
SHOWER HOSE through the HOLDER and the SHOWER ESCUTCHEON.
Insert a SEAL WASHER into the SHOWER HOSE CONNECTOR.
Pull out the SLEEVE GUARD and HOSE. Unthread the SLEEVE GUARD
from the HOSE END connection. Be careful not to allow the HOSE to
fall back through the SLEEVE.
Thread the SHOWER HOSE onto the HOSE END connection and tighten
securely.
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
SHOWER HOSE
HOSE
HOSE END
SHOWER HOSE
SET SCREW
RUBBER RING
SHOWER ESCUTCHEON
SHOWER
ESCUTCHEON
HOLDER
SEAL WASHER
S
EAL WA
S
HE
R
SLEEVE
GUARD
SLEEVE
SEALANT
HAND SHOWER
HAND SHOWER
HOLDER
SEAL WASHER
HANDLE
SCREW
INSTALL HANDLE TRIM
INSTALL HAND SHOWER
Turn HANDLE STEM fully clockwise (Tub Filler position).
Place the HANDLE on the HANDLE STEM. Install the
HANDLE SCREW and tighten securely.
Push the INDEX BUTTON into the top of HANDLE. HANDLE
STEM
HANDLE
INDEX
BUTTON
M968356
Apply a sealant around the HOSE HOLE.
Thread the SHOWER ESCUTCHEON into the SLEEVE until the ESCUTCHEON
contacts the finished deck.
Loosen the SET SCREW in the SHOWER ESCUTCHEON and rotate the
ESCUTCHEON towards the center of the tub. Retighten the SET SCREW.
Thread the HOLDER into the SHOWER ESCUTCHEON.
Insert a SEAL WASHER into the SHOWER HOSE
connector and connect the HAND SHOWER.
Place the HAND SHOWER into the HOLDER.
SLEEVE

ROUGH VALVE KIT
DECK MOUNT
TUB SYSTEMS
Installation
Instructions
M968650C
R800 SERIES
R810 SERIES
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1
1ROUGHING-IN
2MOUNT SPOUT SHANK
U.S. Patent No. D403,750
FINISHED DECK VARIABILITY ACCOMMODATES
DECKING MATERIAL (TILE, MARBLE, CORIAN®...)
TO 1" THICK
2. FINISHED DECK
3. FITTING MOUNTING SURFACE
4. ACRYLIC BATHS
DECK MOUNTING HOLES
ADJUSTABILITY, TO 1-1/2" THICK
1. DECK THICKNESS
TOTAL DECK THICKNESS UP TO 2-1/2"
ADJUSTABILITY, TO 1-1/2" THICK
Insert the SPOUT SHANK through the mounting deck from below. Assemble the SPOUT SHANK LOCK RING so it
is flush with the top of the threads on the SHANK.
Drill holes in mounting deck as shown. The maximum allowable deck thickness is 1-1/2".
2
3
4
FINISHED
DECK
FITTING
MOUNTING
SURFACE
ACRYLIC
BATH
MOUNTING
1
1/2" COPPER
INLET SUPPLIES
1-3/8 D
MAX.
1 D MAX.
1" D
(2) 1-3/8 D
HOLES
(2) 1-3/8 D
HOLES
1" D
8" to 12"
10" for R810
8" to 12"
10" for R810
7-1/8
SPOUT SHANK LOCK RING FLUSH WITH
TOP OF THREADS ON SPOUT SHANK
SPOUT SHANK
LOCK RING
SPOUT SHANK
FITTING
MOUNTING
DECK
FRICTION WASHER
SPOUT SHANK
MOUNTING NUT
1-1/2 MAX.
R800 SERIES
R810 SERIES

M968650C
3MOUNT VALVE BODIES
4SOLDER CONNECTIONS
Insert the VALVE BODIES and TEE through the mounting
deck from below. Assemble the VALVE LOCK RINGS so
they are flush with the top of the VALVE BODIES.
Insert the HOT and COLD VALVE BODIES into the TEE. (Not
necessary for R810). The HOT VALVE BODY is
marked with a red label.
Insert the SPOUT SHANK into the TEE.
(Not necessary for R810).
Turn on the water supplies and check all connections for leakage.
Replace the GUARD on the SPOUT SHANK. Turn off the water supplies.
Solder all TEE and WATER SUPPLY CONNECTIONS.
Connect the water supply lines to the copper inlet tubes of the VALVE BODY.
Remove the GUARD from the SPOUT SHANK. Assemble the 1/4" PLUG to
the SPOUT SHANK with a thread sealant.
Tighten the VALVE BODY and SHANK MOUNTING
NUTS securely.
VALVE
LOCK RING
FITTING
MOUNTING
DECK
VALVE
LOCK RING
1/4" PLUG
SPOUT GUARD
TEE
CONNECTIONS
WATER SUPPLY
CONNECTIONS
OUTLET TUBE
(CUT AS REQUIRED)
TEE
HOT
COLD
FRICTION WASHER
MOUNTING NUT
SPOUT
SHANK
Cut the copper outlet tubes of the VALVE BODIES as required.
(Not necessary for R810).
VALVE LOCK RING FLUSH WITH
TOP OF THREADS ON VALVE SHANK
VALVE
BODY
# 8 SCREWS
Fasten the VALVE LOCK RING to the wooden mounting
surface with #8 screws (not provided).
5SERVICE
VALVE
LOCK NUT
SLEEVE
SCREW
VALVE
CARTRIDGE
Turn off the water supplies.
Turn HANDLE to the off position.
Unscrew the VALVE LOCK NUT and remove.
A 17mm deep socket is required.
Remove the CARTRIDGE by pulling upon the SLEEVE.
Remove the SLEEVE from the CARTRIDGE.
Remove the SPRING CLIP.
Remove the STOP WASHER. Turn it 90˚and replace.
Replace the SPRING CLIP.
Reverse the above steps to reassembly the components.
If the spout drips, operate the handles several times
from the off to the on position. Do not force - the handles only turn 90˚
SPRING
CLIP
STOP
WASHER
90
TO CHANGE THE DIRECTION OF HANDLE ROTATION DEEP SOCKET
17mm (11/16")

Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 2003
C
M968650C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
SPOUT LOCK RING
A906110-0070A
SPOUT MOUNTING KIT
M962279-0070A
VALVE LOCK NUT
A911546-0070A
VALVE LOCK RING
M906671-0070A
SPINDLE
903898-0070A
SCREW
918319-0070A
VALVE CARTRIDGE
994053-0070A
DEEP SOCKET
17mm (11/16")
M962273-0070A
SOCKET NOT INCLUDED
WITH FITTING
VALVE MOUNTING KIT
M962278-0070A
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
R810
R800
MODEL NUMBERS
DECK MOUNT TUB SYSTEMS
R810 SERIES
*WITH BRAZED TEE

DIVERTER & PERSONAL SHOWER
ROUGH VALVE KIT
DECK MOUNT
TUB FILLERS
Installation
Instructions
M968355D
R890 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1
1ROUGHING-IN
U.S. Patent No. D403,750
FINISHED DECK VARIABILITY ACCOMMODATES
DECKING MATERIAL (TILE, MARBLE, CORIAN®...)
TO 1" THICK
2. FINISHED DECK
3. FITTING MOUNTING SURFACE
4. ACRYLIC BATHS
DECK MOUNTING HOLES
ADJUSTABILITY, TO 1-1/2" THICK
1. DECK THICKNESS
TOTAL DECK THICKNESS UP TO 2-1/2"
ADJUSTABILITY, TO 1-1/2" THICK
2
3
4
FINISHED
DECK
FITTING
MOUNTING
SURFACE
ACRYLIC
BATH
MOUNTING
1
1/2" NPT INLET
TUB
SHW
1/2" NPT
1-3/8 D
MAX. 1-3/8 D
MAX.
1-
3/8
D
1-3/8 D
HOLE
1-3/8 D HOLE
FOR HAND
SHOWER
1-3/8 D HOLE
FOR DIVERTER
6 to 18
6 to 18
4-5/16
3-5/8
5-5/16
8" to 12"
"A" DIMENSION CAN BE
FLEXIBLE TO
ACCOMMODATE
CUSTOMER'S
REQUIREMENTS
PLUMBER TO MAKE ALL PIPING CONNECTIONS
BETWEEN VALVE BODIES, SUPPLY TO TRANSFER
VALVE AND CONNECTION TO BATH SPOUT.
PIPING SHOWN SHADED IS NOT SUPPLIED
AND MUST BE FURNISHED BY INSTALLER.
TUB
SHW
1/2" COPPERWATER
TUBE INLET (MIXED
SUPPLY FROM BATH
FITTING) HOSE OUTLET
(MIXED SUPPLY
TO HAND SHOWER)
1/2" COPPERWATER
TUBE (MIXED SUPPLY
TOTUB FILLER SPOUT)
BATH SPOUT
CONNECTION DIVERTER
VALVE
HAND SHOWER
CONNECTION
HOT AND COLD
VALVE BODIES
HOT
INLET COLD INLET
A A 6" to 18"
R800 ROUGHVALVE KIT R890 SERIES DIVERTER & PERSONAL
SHOWER ROUGH VALVE KIT
2LOCATION OF R890 WHEN USED WITH R800