American Standard CADET 3985 Series User manual

DECK-MOUNT
BATH FILLER
Installation
Instructions
M968236 Rev.1.2
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789; D405,165
Required Tools
*Supplied with Fitting
*Hex key
RECESS
Turn off hot and cold water supplies before beginning.
CAUTION
12
Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (2) is properly seated in RECESS
at base of SPOUT (3).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (1). From underside of ledge secure SPOUT (3) into position
with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
3
4
2
3
1
3
4
1
2
4
6
5
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
ADJ. 6-1/2 TO 12
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
3985 Series
MOUNTING
LEDGE.
VALVE inlet is 3/4-inch NPT male connector.
NOTE
TM
1-1/4
MAX. 3
(H) (C)
1-1/8 D.
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
1-1/16 D.
4-3/4
7-1/4
6-5/8
4
3/4-14 MALE
N.P.T. INLETS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

M968236 Rev.1.2
10
5
5/16'' MIN. MOUNTING SURFACE
11
11 10
11
1
5
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Loosen HANDLE SET SCREW (2) and
pull off HANDLE (1).
Remove ADAPER SCREW (3) and pull
off Adapter (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90 and replace.
Replace SPRING CLIP (6).
Reinstall ADAPTER (4) and complete HANDLE
ASSEMBLY.
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90˚.
90˚
SERVICE 6CARE
5
6
4
3
INSTALL HANDLES
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to
SPOUT SHANK (7) and tighten.
Install MOUNTING NUT (1) onto valve shanks.
Place RUBBER RING (11) into ESCUTCHEON (10) and thread onto
valves until snug against internal stop.
Tighten MOUNTING NUT (1) to secure VALVE (5) position.
Slide FERRULE (2) and COUPLING NUT (3) to outlet of VALVE (5) and tighten
COUPLING NUT (3) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH,
ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE
SURFACE.
2
5
3
8
7
9
6
3
2
45
10
MOUNTING
LEDGE
2
1
3
5
4
4
3
2
1
Turn HANDLE STEM (1) to "OFF" position.
Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).
Install the ADAPTER SCREW (3) and tighten securely.
Position LEVER HANDLE (4) and place on ADAPTER (2). Install the
HANDLE SCREW (5) and tighten securely.