American Standard Colony pro TU075507 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of ne quality for over 100 years.
RECOMMENDED TOOLS
M965931 Rev. 1.0 (12/18)
ROUGHING-IN DIMENSIONS
Colony®Pro
Pressure Balancing
Bath and Shower Trim Kit
INSTALLATION
INSTRUCTIONS
TU075500
TU075507
TU075508
TU075507XH
TU075508XH
Plumbers’ Putty
or Caulking
Adjustable Wrench Channel Locks
Phillips Screwdriver
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
OFF
Teon Tape
Flat Blade Screwdriver
CARTRIDGE INSTALLATION
11
1
2
6
5
3
4
UP
UP
FINISHED WALL
4" (102 mm)
TOP OF TUB RIM
BOTTOM OF TUB
74" (1879 mm)
FOR HEAD
CLEARANCE
4-1/16"
(99 mm)
2" TO 3"
(51 TO 76 mm)
18" (457 mm)
OPTIONAL
4-7/8"
(124 mm)
5-11/16"
(144 mm)
1/2" NPT
1/2" COPPER
FOR SLIP-ON
SPOUT
7-1/2" DIA.
(190 mm)
1-1/2"
(38 mm)
4-3/16"
(106 mm)
7-1/2"
(190 mm)
8-9/16"
(217 mm)
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78"
(1651 AND 1981 mm)
6-1/8"
(155 mm)
2-7/8"
(72 mm)
2-3/4" MAX. (69 mm)
1-3/4" MIN. (45 mm)
3-3/4"
(96 mm)
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
• Remove PLASTER GUARD (6)
(Keep it installed for thin wall Installation).
• Remove BONNET NUT (1) by unthreading it
Counter clockwise. Remove test CAP (2).
• Remove PROTECTIVE HOUSING (3) from
CARTRIDGE (4). Install with “UP” text on top.
• Reinstall BONNET NUT (1) onto VALVE BODY (5)
and tighten rmly with 12 Nm or 9 lbs/ft.
NOTE: Specied tightening torque
of BONNET NUT (1) is critical to
assure sealing function.

- 2 -
OFF
UP
4
2
UP
1
1
2
UP
1
PLASTER
GUARD
Figure 2.
Figure 1.
Figure 1a.
4
3
OFF
1
Figure 2a. 4
3
2
• Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)
and tightening SET SCREW (3) from below with 2.5 mm
Hex Wrench supplied.
HANDLE INSTALLATION
4
M965931 Rev. 1.0 (12/18)
3INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
• Remove pipe cap and plug from shower and tub rough piping.
• Slip TUB SPOUT (1) onto tub nipple and tighten with 2.5 mm Hex Wrench.
CAUTION: Protect nish on TUB SPOUT when installing.
• Install SHOWER ESCUTCHEON (2) onto SHOWER ARM (3). Apply sealant
or Teon tape to threads on both ends of SHOWER ARM (3) and thread
longer leg of SHOWER ARM (3) into shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect nish on SHOWER HEAD and ARM when installing.
• Slip ADAPTER (5) onto CARTRIDGE (6) and thread SCREW (7) on.
CAUTION Protect nish on SHOWER HEAD
and TUB SPOUT when installing. PIPE
PLUG
4
3
2
SHR.
ELBOW
TUB FILLER
NIPPLE
5
7
1-1/2" REF.
2.5 MM HEX
WRENCH
6
1
OFF
3
2.5 MM HEX
WRENCH
1
OFF
2
• Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
THIN WALL INSTALLATION
• Figure 1a. Push CAP (1) over VALVE CARTRIDGE (2) until
seated against stop.
• Figure 2a. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
STANDARD WALL INSTALLATION

- 3 -
M965931 Rev. 1.0 (12/18)
7CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
6
5
• By restricting HANDLE rotation and limiting the amount of hot water
allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1)
reduces risk of accidental scalding. To set the maximum hot water
temperature of your faucet valve, adjust the setting on the HOT LIMIT
SAFETY STOP (1).
• Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before
making adjustment to HOT LIMIT STOP (1). Pull forward and rotate
counterclockwise one number to limit hot water temperature.
Use NUMBERS (5) on CARTRIDGE (4) on HOT LIMIT STOP (1)
for indication.
ADJUST HOT LIMIT STOP
COLDER
(Larger Numbers)
1 2 3 4 5 6 7 8 9 10
HOTTER
(Smaller Numbers)
1 2 3 4 5 6 7 8 9 10
3
4
1
5
2
VALVE LEAKS WHEN SHUT OFF
• Remove CARTRIDGE, see STEP 1 and STEP 2 and REVERSE process.
• Clean SEALS on the side of CARTRIDGE. Clean inside sealing surface of VALVE BODY.
• Re-assemble CARTRIDGE. Install trim. Turn on water supply and check for leaks.
REPLACING CARTRIDGE
• To remove CARTRIDGE (1), install split WASHER (3) between the ridge on the cartridge and the bonnet nut (only
supplied with replacement cartridge) as shown.
• Proceed to unthread BONNET NUT (2) counter clockwise.
Note: CARTRIDGE (1) should be pulling out while unthreading BONNET NUT (2).
• Upon removal of the old Cartridge, install a new cartridge and secure it with BONNET NUT
(Hand tighten).
BACK TO BACK INSTALLATION
• NOTE: Must purchase specialized back to back cartridge. (Part number M970640-0070A)
• Remove CARTRIDGE (1) as detailed in steps above.
• Install back to back cartridge.
• Remove HANDLE (see step 3 and reverse).
• Remove ESCUTCHEON and CARTRIDGE CAP (see step 1 and reverse).
SERVICE
TO GAIN ACCESS TO VALVE FOR SERVICING CAUTION Turn off hot and cold water
supplies before beginning.
Figure 1.
1
3
2

- 4 -- 4 - M965931 Rev. 1.0 (12/18)
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M970179-YYY0A
SHOWER ARM & FLANGE
1660512.YYY
SHOWER HEAD
M970178-YYY0A
ESCUTCHEON KIT
M907327-YYY0A
CARTRIDGE CAP
M970177-YYY0A
HANDLE KIT
M950372-YYY0A
SLIP-ON TUB SPOUT
M970457-0070A
ADAPTOR KIT
078016-YYY0A
CARTRIDGE SCREW
M970410-0070A
CARTRIDGE
OFF
M954805-YYY0A
DEEP ROUGH-IN
KIT
PURCHASE SEPARATELY
PURCHASE SEPARATELY
M970640-0070A
BACK-TO-BACK
CARTRIDGE
MODEL NUMBER
TU075500
TU075507
TU075508
TU075507XH
TU075508XH
Replace the “YYY” with
appropriate nish code
POLISHED CHROME 002
LEGACY BRONZE 278
BRUSHED NICKEL 295
Colony®Pro
Pressure Balancing
Bath and Shower Trim Kit