American Standard QUINCE 4433.410 User manual

SINGLE CONTROL
PULL-DOWN BAR FAUCET
4433.410
4433.410F15
Thank you for selecting American-Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Installation
Instructions
Certified to comply with ANSI A112.18.1M
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
3
7
AB
PUTTY
SPOUT BASE
SINK OR
MOUNTING
SURFACE
SPOUT BASE
2
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Turn off water at
main supply.
CAUTION
QUINCE™
7
9
9
3
2
M965243 REV. 1.8 (4/19)
1
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7)
and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions
below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9)
is properly seated in recess of faucet body.Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting
hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
4
5
8
7
6
4
5
8
7
6

6
7
8
18"
1
2
3
!
UNSCREWBEFORE
INSTALLING
4
5
2MAKE WATER SUPPLY CONNECTIONS
4TEST INSTALLED FAUCET
SPRAY OPERATION
3
Move HANDLE (1) into "off"
position.
With HANDLE (1) in "off" position,
unthread SPRAY (3) from HOSE (2).
Turn on water supplies. Operate handle back to front, in COLD
and HOT positions, to flush water lines
thoroughly.
Replace SPRAY (3) onto HOSE (2).
With FAUCET on pull down
SPRAY (4). Check for leaks.
Make sure SPRAY (4) fully
retracks and is seated in
the SPOUT HOLDER (5).
Check connections for leaks.
(See Section 5)
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
1
2
COLD
HOT
M965243 REV. 1.8 (4/19)
REMOVE
CONNECT SPRAY HOSE & INSTALL WEIGHTS
Remove the FAUCET PROTECTION DEVICE (1) from the
COUPLING NUT (2).
Connect threaded end of HOSE (3) to SPRAY HOSE
COUPLING NUT (2) from fitting. Use wrench to tighten.
With HAND SPRAY (4) seated in SPOUT (5), install WEIGHT (7)
onto HOSE (6) 18 inches from the underside of the sink deck
and secure with SCREW (8).
1
3
2
5
4

1
2
4
5
6
86a
3
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
5
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
7
M965243 REV. 1.8 (4/19)

QUINCE™
MODEL NUMBER
M964395-0070A
WEIGHT
A911836-0070A
SEAL
M962806-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the YYY with
Appropriate finish code
M964178-YYY220A
(2.2 GPM)
SPRAY ASSEMBLY
M964178-YYY150A
(1.5 GPM)
SPRAY ASSEMBLY
M918506-0070A
CARTRIDGE SCREWS
M964176-YYY0A
HANDLE KIT
A951470-0070A
CARTRIDGE
M964175-0070A
SPOUT BUSHING & O-RING KIT
M917147-0070A
SPOUT SET SCREW
M907306-YYY0A
ESCUTCHEON CAP
M962294-0070A
BUTTON AND
SCREW KIT
SINGLE CONTROL
PULL-DOWN BAR FAUCET
4433.410
4433.410F15
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M965243 REV. 1.8 (4/19)
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2019
M922367-007220A
SPRAY HOSE
2.2gpm/8.3L/min.
M922367-007150A
SPRAY HOSE
1.5gpm/5.7L/min.