American Standard Culinaire Bar/Pantry Faucet 4233.400 User manual

Installation
Instructions
.3&7
Certified to comply with ANSI A112.18.1M
4233.400
INSTALL FAUCET
Turn off hot and cold water
supplies before beginning.
CAUTION
3FDPNNFOEFE5PPMT.BUFSJBMT
"EKVTUBCMF8SFODI
$IBOOFM-PDLT
3FHVMBS4DSFXESJWFS
1IJMMJQT4DSFXESJWFS
1MVNCFSTh1VUUZPS
$BVMLJOH
5VCJOH$VUUFS
Culinaire
BAR/PANTRY FAUCET

Insert supply TUBES (2) and SHANK (3) through hole of sink or
mounting surface
Make certain the large O-RING (1) is properly seated in recess of
faucet body.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and thread
LOCKNUT (6) onto SHANK (3) from underside of sink. Hand tighten
LOCKNUT (6) Check that FAUCET is centered.
NOTE: Set screw is in back of faucet body.
Use a screwdriver to tighten the SCREWS (7) on LOCKNUT (6).
Alternate tightening the SCREWS (7) slightly each time
until snug to ensure even pressure.
RECESS
SET SCREW
(IN BACK)
1
3
2
4
5
6
7
Congratulations on purchasing your American Standard faucet with
EverClean nish found only on American Standard faucets.
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these nishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish

.3&7
MAKE WATER SUPPLY CONNECTIONS
Connect water supplies to SUPPLY ADAPTERS (1)
with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D.
BULL-NOSE RISERS (3).
Use tubing cutter to cut to proper length.
Connect the HOT to the left supply and the
COLD to the right supply.
Use adjustable wrench on coupling nut and
another wrench on supply adapters to prevent
twisting of supply tubes. Tighten connections.
Do not over tighten. Be careful not to kink
copper supply when bending.
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
5
6
3
4
1
2
2
1
3
FERRULE
COLD
HOT
Aerator may accumulate dirt causing distorted and reduced water flow.
Remove aerator and rinse clean.
If spout drips, operate handles several times from ON to OFF position.
Do not force-handles turn only 90˚.
If faucet drips proceed as follows:


To change direction of handle
rotation, proceed as follows:
Turn valve to OFF position.
Remove INDEX CAP (1). Remove
HANDLE SCREW (2).
Pull off HANDLE (3) and pull off
HANDLE BASE (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (6).
Reinstall HANDLE BASE (4) and HANDLE
ASSEMBLY (3,2,1).
SERVICE
90˚
TEST INSTALLED FAUCET
Remove AERATOR (1). With handles in OFF position,
turn on WATER SUPPLIES (2) and check all connections
for leaks.
Operate both HANDLES (3) to flush water lines
thoroughly. Rotate SPOUT (4) in both directions.
Replace AERATOR (1).
14
2
3