American Standard Neolo Elongated Flush Valve Toilet 2529.016 User manual

M51
© 2008 AS America Inc.
To Be Specied:
❏ Color: ❏ White
❏ Seat: Olsonite #95 open front seat less cover
❏ Seat: Church #9500C open front seat less cover
❏ Seat: Pressalit seats for American Standard,
closed front seat with cover (thermoset
compound material).
❏ Alternate Seat:
❏ Flush Valve:
❏ American Standard Selectronic™ #6065.161.002
DC Power(Top Spud)
❏ American Standard Selectronic™ #6065.262.007
DC Power (Back Spud)
❏ American Standard Selectronic™ #6067.262.007
AC Power (Back Spud)
❏ American Standard Selectronic™ #6068.262.007
Multi AC Power (Back Spud)
NEOLO™
ELONGATED FLUSH VALVE TOILET
VITREOUS CHINA
NEOLO™ ELONGATED FV TOILET
• Elongated ush valve toilet
• Vitreous china
• Low consumption (6.0 Lpf/1.6gpf)
• Wall outlet elongated bowl, angle back and base
• Siphon jet ush action
• Fully glazed 2" ballpass trapway
• 10" x 13" water surface area
• 1-1/2" inlet spud
• 4 bolt caps
• 100% factory ush tested
❏ 2529.016 Elongated bowl only, top spud,
wall outlet
❏ 2530.016 Elongated bowl only, back spud,
wall outlet
❏ 2531.016 Elongated bowl only, back spud,
wall outlet, integral seat
Nominal Dimensions:
673 x 375 x 375mm
(26-1/2" x 14-3/4" x 14-3/4")
Recommended working pressure – between
30 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps, and ush valve
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
Revised 11/08

M52
© 2008 AS America Inc. Revised 11/08
NEOLO™
ELONGATED FLUSH VALVE TOILET
VITREOUS CHINA
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-
FELT (WAX RING NOT RECOMMENDED).
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM
BREAKER ON FLUSH VALVE, THE PLUMBER MUST VERIFY
DIMENSIONS SHOWN FOR SUPPLY ROUGHING.
FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
2529.016 2530.016
FINISHED WALL
FINISHED
FLOOR
521mm
(20-1/2)
267mm
(10-1/2)
76mm
(3)
108mm
(4-1/4)
673mm
(26-1/2)
470mm
(18-1/2)
375mm
(14-3/4)
C/L OF
OUTLET
375mm
(14-3/4)
222mm
(8-3/4)
152mm
(6)
13mm(1/2)
375mm
(14-3/4)
C/L OF SEAT POST HOLE
140mm (5-1/2) CENTERS
660mm
(26)
C/L OF 1/2" DIA. BOLT
HOLES ON 140mm (5-1/2) CENTERS
1-1/2" SPUD
121 mm
(4-3/4)
1" N.P.T. OR C.W.T.
SUPPLY TO FLUSH VALVE
FINISHED WALL
1-1/2"
SPUD
70mm (2-3/4)
DIA. HOLE
IN WALL
191mm (7-1/2)
DIA. HOLE
IN WALL
INTEGRAL SEAT
(2531.016)
FINISHED
FLOOR
375mm
(14-3/4)
222mm
(8-3/4)
152mm
(6)
521mm
(20-1/2)
267mm
(10-1/2)
108mm
(4-1/4)
225mm
(8-7/8)
673mm
(26-1/2)
470mm
(18-1/2)
375mm
(14-3/4)
C/L OF
OUTLET
13mm
(1/2)
C/L OF SEAT POST HOLE
140mm (5-1/2) CENTERS
(2530.016)
C/L OF 1/2" DIA. BOLT
HOLES ON 140mm (5-1/2) CENTERS
FINISHED WALL
1-1/2"
SPUD
121mm
(4-3/4)
VACUUM
BREAKER
1" N.P.T. OR
C.W.T. SUPPLY
70mm (2-3/4)
DIA. HOLE
IN WALL
191mm (7-1/2)
DIA. HOLE
IN WALL
572mm
(22-1/2)
610mm
(24)
95mm
(3-3/4)
OPENING IN WALL
38mm (1-1/2) DIA.
INTEGRAL SEAT
(2531.016)
FOR WALLS UP TO 25mm (1") IN THICKNESS;
FOR EACH 25mm (1-INCH) ADDITIONAL THICKNESS
OF WALL ADD 25mm (1") TO THIS DIMENSION
FINISHED
FLOOR
375mm
(14-3/4)
222mm
(8-3/4)
152mm
(6)
521mm
(20-1/2)
267mm
(10-1/2)
108mm
(4-1/4)
225mm
(8-7/8)
673mm
(26-1/2)
470mm
(18-1/2)
375mm
(14-3/4)
C/L OF
OUTLET
13mm
(1/2)
C/L OF SEAT POST HOLE
140mm (5-1/2) CENTERS
(2530.016)
C/L OF 1/2" DIA. BOLT
HOLES ON 140mm (5-1/2) CENTERS