American Standard Fixture-Mounted Bidet Fitting 2580 User manual

Installation
Instructions
M968292
Certified to comply with ASME A112.18.1M
U.S. Patent No. ,819,789
Roughing-in Dimensions
(C) (H)
8 TO 12
Turn off hot and cold water
supplies before beginning.
CAUTION
1
DRAIN INSTALLATION
2
OUNTING BIDET FAUCET
STOPPER
Assemble O-RING (1), WASHER (2), PIVOT
ROD (3) and NUT (4) to DRAIN BODY ( ).
Concave side of cup WASHER (2) is toward
ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY ( ).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY ( ) up through BIDET
and thread FLANGE (9) fully onto
BODY ( ).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
BIDET
PUTTY
CLIP
9
3
1
4
11
6
5
8
72
10
2580
BIDET FITTING
*Wrench
*Supplied with Fitting
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Required Tools
Tubing Cutter
by
COLLECTION
™
THE
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
thread DECK ADAPTER (4) onto VALVE BODIE (2)
until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Replace UPPER GASKET (7), and ESCUTCHEON ( )
until it locks against the internal stop. Position the
side threaded outlet rearward and secure
MOUNTING NUT (9).
COLD
HOT
BIDET
LEDGE
3
4
2
7
8
1
9
5
Remove ESCUTCHEON ( ), WASHER (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and
insert into the center forward hole of BIDET.
10
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY 2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
-1/2
1-3/8
DIA.
7/8 DIA.
1-3/8
MAX.
1-3/16
DIA.
2-1/4
DIA.
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
Thank you for selecting American- tandard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds
smoothly--please read these instructions carefully before you begin.

4
Unscrew LIFT ROD NUT (1)
from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated
into ESCUTCHEON of LIFT ROD
GUIDE (2).
Drop LIFT ROD GUIDE (2) into
rear hole of bidet and from
below secure with LIFT ROD
NUT (1). 1
3
2
Cold
Hot
Front
M968292
LIFT ROD GUIDE INSTALLATION
Install HANDLE ADAPTER (8) onto valve stem (12).
Push DIVERTER KNOB (7) onto HANDLE ADAPTER (8).
Install RING (9) onto DIVERTER KNOB 7) and tighten with
SCREW (10).
Press on KNOB CAP (11).
6
1
2
TOP
Figure "A"
SPLINE END DOWN
INSTALL HANDLES
4
3
7
5
6
Push INDEX CAP (6) in hole of HANDLE (4).
Secure HANDLE (4) with HANDLE SCREW ( ).
Find correct position of HANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HANDLE (4).
Thread HANDLE BASE (3) onto DECK ADAPTER (7)
Push HANDLE (4) onto ADAPTER (1).
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
SPRAY INSTALLATION
3
Assemble SPRAY BODY (1) to BIDET. Apply putty to
underside of SPRAY BODY FLANGE (2) to seal and
secure with NUT (3).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
Thread SPRAY HOSE (4) with SEAL WASHER ( ) to
SPRAY BODY (1). Connect other end of HOSE (4) with
SEAL WASHER (6) to bottom outlet NIPPLE (7) of the
TRANSFER VALVE (8).
PUTTY
6
2
7
8
1
3
5
4
9
Insert SEAL (1) into ADAPTER (2) and tighten
ADAPTER (2) to side inlet of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE ( )
and tighten connection to ADAPTER (2)
Connect HOSE COUPLING NUTS (6)
to Hot and Cold valve bodies
and securely tighten.
TEE AND HOSE CONNECTION
5
3
1
2
4
5
6
6
8
12
11
10
9
7
LEVER HANDLE :
DIVERTER KNOB:

SERVICE
To change direction of handle
rotation, proceed
as follows:
Turn valve to OFF position.
Remove HANDLE and
ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2),
turn 90° and replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
90°
WATER SUPPLY CONNECTIONS
7
Cold
Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
FERRULE
COUPLING NUT
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE
TO BE PURCHASED SEPARATELY
8FINISH DRAIN INSTALLATION
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Using metal TAILPIECE ( ), make connection to the TRAP (6).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1)
and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and
tightening THUMBSCREW (3).
3
31
1
2
1
1
7
4
6
5
2
2
Replace SPRAY (3) and operate
handles several times from
OFF to ON position. Do not
force, handles turn only 90˚.
SPRAY (3) may accumulate dirt
causing distorted and reduced
water flow. Unscrew and remove
SPRAY (3) and rinse clean. 3
M968292
Operate Lift Rod (3) and fill
Bidet with water. Check that
DRAIN STOPPER (4) makes
a good seal and retains
water in Bidet. Adjust
stopper height by
repositioning Lift Rod (3) and
tightening Thumbscrew ( ).
Release DRAIN STOPPER (4) and
check all drain connections for
leaks. Tighten if necessary.
9TEST INSTALLED FITTING
With HANDLES (1) in OFF
position, turn on WATER
SUPPLIES (2) and check all
connections for leaks.
Operate both handles to flush
water lines thoroughly. Turn
DIVERTOR (6) to rim wash and
bidet spray.
1
3
5
2
2
6
11
10
DO: SI PLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE
CARE INSTRUCTIONS:
4

M968292
CHROME
SATIN 002 29
Replace the "YYY" with
appropriate finish code
BIDET FITTING
ODEL NU BER
2581
by
COLLECTION
™
THE
024220-0070A
COUPLING NUT
962164-0070A
LIFT ROD
961656-YYY0A
LIFT ROD GUIDE
060463-0070A
ADAPTER KIT
028704-0070A
TEE AND HOSE KIT
(INCLUDING SEALS)
923348-0070A
HANDLE ADAPTER
030281-0070A
TRANSFER VALVE
MOUNTING KIT
028646-0070A
SPRAY HOSE
CONNECTION KIT
028645-YYY0A
BIDET SPRAY
953800-0070A
TRANSFER VALVE
918428-0070A
HANDLE SCREW
962182-YYYOA
HANDLE
013312-YYYOA
ESCUTCHEON KIT
994053-0070A
CARTRIDGE
962161-0070A
DECK ADAPTER KIT
918049-0070A
HANDLE ADAPTER
908505-YYY0A
ESCUTCHEON
918428-0070A
HANDLE SCREW
962163-0070A
INDEX BUTTON (COLD)
962162-0070A
INDEX BUTTON (HOT)
962165-YYYOA
LEVER HANDLE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-90 -306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
961634-0070A
VALVE MOUNTING KIT
030280-0040A
TAILPIECE WITH
ESCUTCHEON
072574-0070A
EXTENSION
066116-YYY0A
DRAIN STOPPER
961711-0070A
TAILPIECE INSERT
070847-0070A
CLIP
066118-0070A
PIVOT ROD KIT
( -7/16" lg.)
953451-YYY0A
COMPLETE
DRAIN ASSEMBLY
066117-YYY0A
2" FLANGE KIT

Installation
Instructions
M968293
Certified to comply with ASME A112.18.1M
U.S. Patent o. 5,819,789
Roughing-in Dimensions
BIDET OUTLI E
IS SYMBOLIC
FI ISHED
FLOOR
FI ISHED
WALL
1-1/4 O.D. TAILPIECE
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
DIVERTER A D
VACUUM BREAKER
ASSEMBLY
1-1/4 MAX.
1-3/16 DIA.
(C) (H)
4-1/4
FOR GROU D JOI T
CO ECTIO OR 1/2 "
O.D. SLIP (I LETS)
REAR VIEW WITH
WALL REMOVED
TRA SFER VALVE (FOR FLUSHI G
RIM OR SPRAY)
8 TO 12
2-1/4
DIA.
Turn off hot and cold water
supplies before beginning.
CAUTION
1MOUNTING BID T FAUC T
Tighten the MOU TI G UT (1) to secure the
VALVE BODIES (2).
Replace UPPER GASKET (7) and FRICTIO RI G (10).
Position the side threaded outlet rearward and secure
MOU TI G UT (9). Thread ESCUTCHEO (5) onto
TRA SFER VALVE (8) until it seats against the
BIDET LEDGE.
Remove MOU TI G UT (9), FRICTIO RI G (10)
and UPPER GASKET (7) from TRA SFER VALVE (8)
and insert TRA SFER VALVE (8) into the center
forward hole of BIDET.
DOUCHE SPRAY 2-1/8
DIA.
2581
BID T FITTING
*Wrench
*Supplied with Fitting
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Required Tools
Tubing Cutter
3
4
COLD
HOT
BIDET
LEDGE
2
7
8
1
9
10
5
by
COLLECTION
™
THE
Place MOU TI G UTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RI G (3) over the VALVE BODIES (2) and
thread DECK ADAPTER (4) onto VALVE BODIE (2)
until it locks against the internal stop.
Thank you for selecting American- tandard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds
smoothly--please read these instructions carefully before you begin.
DRAIN INSTALLATION
2STOPPER
Assemble O-RI G (1), WASHER (2), PIVOT
ROD (3) and UT (4) to DRAI BODY (5).
Concave side of cup WASHER (2) is toward
ball.
Thread LOCK UT (6), WASHER (7) and
GASKET (8) onto DRAI BODY (5).
Apply a bead of PUTTY to underside
of FLA GE (9).
Feed DRAI BODY (5) up through BIDET
and thread FLA GE (9) fully onto
BODY (5).
Tighten LOCK UT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAI ESCUTCHEO (10) onto
TAILPIECE (11).
BIDET
PUTTY
CLIP
9
3
1
4
11
6
5
8
72
10

SPRAY INSTALLATION
4
Assemble SPRAY BODY (1) to BIDET. Using putty, seal
underside of SPRAY BODY FLA GE (2) and secure with
UT (3).
Screw SPRAY CAP (9) onto SPRAY BODY (1).
Screw SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY
BODY (1). Connect other end of HOSE (4) with SEAL
WASHER (6) to side outlet IPPLE (7) of the TRA SFER
VALVE (8).
PUTTY
COUPLI G
UT
6
2
7
8
1
3
5
4
9
5
Unscrew LIFT ROD UT (1)
from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated
into ESCUTCHEO of LIFT ROD
GUIDE (2).
Drop LIFT ROD GUIDE (2) into
rear hole of bidet and from
below secure with ROD GUIDE
UT (1).
T AND HOS CONN CTION
3
1
3
2
3
Cold
Hot
Front
1
2
4
5
6
6
Insert SEAL (1) into ADAPTER (2)
and tighten ADAPTER (2) to bottom
of TRA SFER VALVE (3).
Install SEAL (4) into coupling nut
of TEE (5) and tighten connection
to ADAPTER (2)
Connect HOSE COUPLI G
UTS (6) to Hot and Cold
valve bodies and securely
tighten.
M968293
LIFT ROD GUID INSTALLATION
VALVE STEM
13
12
11
9
10
Install HA DLE ADAPTER (10) onto valve stem.
Push DIVERTER K OB (9) onto HA DLE ADAPTER (10).
Install RI G (11) onto DIVERTER K OB (9) and tighten with
SCREW (12).
Press on K OB CAP (13).
6
1
2
TOP
Figure "A"
SPLI E E D DOW
INSTALL HANDL S
4
3
7
5
6
Push I DEX CAP (6) in hole of HA DLE (4).
Secure HA DLE (4) with HA DLE SCREW (5).
Find correct position of HA DLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HA DLE (4).
Thread HA DLE BASE (3) onto DECK ADAPTER (7)
Push HA DLE (4) onto ADAPTER (1).
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
LEVER HANDLE :
DIVERTER KNOB:

S RVIC
To change direction of handle
rotation, proceed
as follows:
Turn valve to OFF position.
Remove HA DLE and
ADAPTER if present.
Remove SPRI G CLIP (1).
Lift STOP WASHER (2),
turn 90° and replace.
Replace SPRI G CLIP (1).
Replace HA DLE ASSEMBLY.
90°
WAT R SUPPLY CONN CTIONS
7
Cold
Hot
Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL- OSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
FERRULE
COUPLI G UT
NOT : FL XIBL SUPPLI S AR NOT INCLUD D AND HAV TO B
PURCHAS D S PARAT LY.
8FINISH DRAIN INSTALLATION
Position EXTE SIO ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Using metal TAILPIECE (5), make connection to the TRAP (6).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTE SIO ROD (1)
and reassemble CLIP (4). (EXTE SIO ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTE SIO ROD (1) and
tightening THUMBSCREW (3).
3
31
1
2
1
1
7
4
6
5
2
2
Replace SPRAY (3) and operate
handles several times from
OFF to O position. Do not
force, handles turn only 90˚.
SPRAY (3) may accumulate dirt
causing distorted and reduced
water flow. Unscrew and remove
SPRAY (3) and rinse clean. 3
M968293
Operate Lift Rod (3) and fill
Bidet with water. Check that
DRAI STOPPER (4) makes
a good seal and retains
water in Bidet. Adjust
stopper height by
repositioning Lift Rod (3) and
tightening Thumbscrew (5).
Release DRAI STOPPER (4)
and check all drain connections
for leaks. Tighten if necessary.
9T ST INSTALL D FITTING
With HA DLES (1) in OFF
position, turn on WATER
SUPPLIES (2) and check all
connections for leaks.
Operate both handles to flush
water lines thoroughly. Turn
diverter to rim wash and bidet
spray.
1
3
2
211
10
DO: SIMPLY RINS TH PRODUCT CL AN
WITH CL AR WAT R. DRY WITH A SOFT
COTTON FLANN L CLOTH.
DO NOT: DO NOT CL AN TH PRODUCT
WITH SOAPS, ACID, POLISH, ABRASIV S,
HARSH CL AN RS, OR A CLOTH WITH A
COARS SURFAC
CAR INSTRUCTIONS:
5
4

M968293
024220-0070A
COUPLI G
UT
028645-YYY0A
BIDET SPRAY
030280-0040A
TAILPIECE WITH
ESCUTCHEO
072574-0070A
EXTE SIO
M953131-0070A
TRA SFER VALVE
MOU TI G KIT
M961742-YYY0A
TRA SFER VALVE KIT
M921323-0070A
ELBOW ADAPTER
M953130-0070A
TRA SFER VALVE
923348-0070A
HA DLE ADAPTER
M907617-YYY0A
ESCUTCHEO
TRA SFER VALVE
918428-0070A
HA DLE SCREW M962182-YYYOA
HA DLE
M961663-0070A
ADAPTER KIT
028704-0070A
TEE A D HOSE KIT
(I CLUDI G SEALS)
028646-0070A
SPRAY HOSE
CO ECTIO KIT
M962164-0070A
POP-UP ROD
M961667-YYY0A
LIFT ROD GUIDE
M961634-0070A
VALVE MOU TI G KIT
CHROME
SATI 002 295
Replace the "YYY" with
appropriate finish code
066116-YYY0A
DRAI STOPPER
M961711-0070A
TAILPIECE I SERT
070847-0070A
CLIP
066118-0070A
PIVOT ROD KIT
(5-7/16" lg.)
M953451-YYY0A
COMPLETE
DRAI ASSEMBLY
066117-YYY0A
2" FLA GE KIT
BID T FITTING
MOD L NUMB R
2581
by
COLLECTION
™
THE
994053-0070A
CARTRIDGE
M962161-0070A
DECK ADAPTER KIT
918049-0070A
HA DLE ADAPTER
M908505-YYY0A
ESCUTCHEO
918428-0070A
HA DLE SCREW
M962165-YYYOA
LEVER HA DLE
M962162-0070A
I DEX BUTTO (HOT)
HOT LI E FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
I CA ADA 1-800-387-0369 (TORO TO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
M962163-0070A
I DEX BUTTO (COLD)