American Standard Lakeland 4114.100 User manual

SINGLE CONTROL KITCHEN
PULL-OUT FAUCET with EverClean™ Finish
LAKELAND
Installation
Instructions
Certified to comply with ANSI A112.18.1M
4114.100
1
3
7
AB
CAUTION
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water
supplies before beginning.
PUTTY
SPOUT BASE
SINK OR
MOUNTING
SURFACE
7
2
3
2
.3&7
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Discard ESCUTCHEON with PUTTY PLATE (1).Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
TOOLS REQUIRED
3FHVMBS4DSFXESJWFS
Congratulations on purchasing your American Standard faucet with
EverClean nish found only on American Standard faucets.
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these nishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
4
5
6
8
4
5
6
8

MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
TEST INSTALLED FAUCET

Place WASHER (3) into COUPLING NUT (1)
on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
(May already be assembled).
Slide COUPLING NUT (1) onto HOSE (2)
Feed small end of HOSE (2) through BODY (5) so
HAND SPRAY (4) rests inside SPRAY HOLDER (6).
Thread HOSE END (7) onto OUTLET HOSE ADAPTER (8)
and tighten.
CONNECT SPRAY HOSE
Move HANDLE (1) down into "off"
position.
With HANDLE (1) down in "off"
position.
Turn on water supplies.
Operate handle up and down, in COLD and HOT positions, to
flush water lines thoroughly.
Place WASHER (7) into HOSE END (4) and connect
HAND SPRAY (2) to HOSE END (4). Place HAND SPRAY (2)
back into faucet.
Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Be
careful not to lose WASHER (7). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.
Check HAND SPRAY (2) operation:
With faucet on push front of BUTTON (6) for a broad
cleansing spray.
With HAND SPRAY (4) seated in SPRAY HOLDER (6),
install WEIGHTS (9) onto HOSE (2) using two SCREWS (10).
Locate the WEIGHTS (9) two feet (2') from the underside of
the sink deck. Tighten SCREWS (10) firmly.
1
5
3
2
4
6
7
2
910
8
1
35
2
6
4
24"
7
Check connections for leaks. (See
Section 5)
.3&7
1
2
COLD
HOT

CHECK CONNECTIONS FOR LEAKS.
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS

SERVICE

Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
3
1
2
4
5
6
6A 8
7

If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Pull off ESCUTCHEON CAP (4). Unscrew three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6A).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red HOT LIMIT
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.
discharge temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
HOT LIMIT SAFETY STOP ADJUSTMENT
6
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
3&%3*/()05
-*.*54"'&5:4501
5&.1&3"563&
4&55*/(/6.#&34










































5
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean
water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
EverClean™ Finish Care Instructions
.3&7