American Standard Reliant+ 4205.000 User manual

SECURE FAUCET AND MAKE
WATER SUPPLY CONNECTIONS
Secure FAUCET (1) with ATTACHMENT NUTS (2) supplied.
(HAND TIGHTEN).
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE
SUPPLIES (3) or 3/8"O.D. BULL-NOSE RISERS (4). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending.
Use tubing cutter to cut to proper length.
Certified to comply with ASME A112.18.1M
3
INSTALL FAUCET
FITTING WITH SPRAY
Install FAUCET (1) on sink. (No sealant is required
unless mounting deck on SINK is uneven).
2
1
M968420 REV. 1.1
NOTE: FLEXIBLE SUPPLIES (3, 4) HAVE TO BE PURCHASED SEPARATELY
Place SPRAY HOLDER (1) into separate hole
of SINK (2) and assemble NUT (3) onto shank.
From underside of SINK (2) and hand tighten
NUT (3).
Plumbers' Putty or CaulkingAdjustable Wrench Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
SINGLE CONTROL KITCHEN FAUCETS
4205.000
4205.001
SINK OR DECK
1
1
2
3
(HAND TIGHTEN)
COUPLING NUT
FERRULE
1
3
4
2
Installation
Instructions
0
1
2
3
4
5
6
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Turn off water at
main supply.
CAUTION

4
6
TEST INSTALLED FAUCET
5
7
Remove AERATOR. With handles in OFF position, turn on water supplies and check all connections for leaks.
Operate HANDLE to flush water lines thoroughly. Rotate SPOUT in both directions. Replace AERATOR.
FITTING WITH SPRAY
1
6
5
8
2
7
Direct SPRAY HEAD into sink and activate SPRAY. Check HOSE connections for leaks.
3
4
If faucet drips proceed as follows:
Feed SPRAY HOSE (1) through SPRAY HOLDER (2)
and attach COUPLING NUT (3) of HOSE (1) to
HOSE ADAPTOR (4) on valve body. Tighten
COUPLING NUT (3) firmly.
Make certain that SPACER WASHER (5) and
RUBBER WASHER (6) are attached to
SPRAY HOSE (1) and thread SPRAY HEAD (7)
to NUT (8).
1
SERVICE
2
3
4
Turn VALVE in OFF position.
If faucet drips, operate handle several times from "off" to "on".
Do not apply excessive force.
Clogged CARTRIDGE inlets may cause reduced flow in "full on" hot or cold.
To clean inlets, first turn off water supply, then:
5
Remove HANDLE (1), CAP (2),CARTRIDGE (3), and DISC & SEALS (5).
Clean inlets and MANIFOLD (4). Reassemble CARTRIDGE (3), alternately
tightening screws. Replace CAP and HANDLE. Check flow.
M968420 REV. 1.1
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull up and rotate
red HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust
min./max. discharge temperature. "0" being the hottest to "7"
the coldest temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
6
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING NUMBERS
0
1
2
3
4
5
6
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: