American Standard Avery 4901.380 User manual

Thank you for selecting American Standard...
the benchmark of ne quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965802 Rev.1.2 (11/18)
(A) Installation on 1-hole mounting surface: (please refer to template provided)
• Make certain the SEAL (12) is properly seated in bottom recess of FAUCET (2). Insert CABLES (11), HOSES (3) and SHANK
(4) through mounting ring and deck, seat SPOUT BASE onto sink or mounting surface. Do not use putty.
• From below: Insert CABLES (12) and HOSES (3) through RUBBER WASHER (6), BRASS WASHER (7), and threaded
LOCKNUT (8).
• Assemble RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside
of sink or mounting surface. Hand tighten LOCKNUT (8).
• Make sure faucet is aligned properly with handle on the right and logo facing directly forward.
• Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws
slightly each time until all are snug to ensure even pressure.
(B) Optional: Installation on 3-hole mounting surface: Requires Deck Escutcheon - order separately
• Make certain the SEAL (12) is properly seated in bottom recess of FAUCET (2) and FOAM SEAL (13) is properly
seated in bottom recess of DECK ESCUTCHEON (1). Do not use putty. (Please refer to the template provided)
• Screw in two THREAD RODS (14) onto bottom of DECK ESCUTCHEON (1).
• Place deck escutcheon over mounting holes of the deck.
• Insert SUPPLY CABLES (11), HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK ESCUTCHEON (1) and
mounting surface.
• Follow mounting instructions above
to secure faucet to mounting surface.
Thread the MOUNTING NUTS (10) to
secure DECK ESCUTCHEON.
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
AVERY™
ELECTRONIC PULL-DOWN
KITCHEN FAUCET
INSTALLATION
INSTRUCTIONS
4901.380
Flat Blade Screwdriver Adjustable WrenchPhillips Screwdriver
Certied to comply with ANSI A112.18.1M
B (OPTIONAL)
A
SPOUT BASE
SINK OR
MOUNTING
SURFACE
SPOUT BASE
3
7
9
8
2
12
11
5
3
6
7
9
4
4
8
1
12
13
5
6
10
14
CAUTION Turn off water at
main supply
- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018

2
M965802 Rev.1.2 (11/18)
3CONNECT SPRAY HOSE AND SOLENOID ASSEMBLY,
AND INSTALL WEIGHT
• Turn off hot and cold water supplies before beginning.
• Install INLINE FILTER (3) on each wall supply outlet.
Be sure that INLINE FILTER (3) is inserted in the
correct direction. (See Illustration)
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly
to INLINE FILTER (3). Connection on tting supplies
are 3/8"compression. Connect left supply hose (Red
Stripe) to Hot wall supply. Connect right supply hose
(Blue Stripe) to Cold wall supply. Use adjustable
wrench to tighten connections. Do not over tighten.
*Faucet supplies are 35"long from faucet base.
• Note: If additional supply length is required,
installer must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
8
7
9
3
2
4
1
18"
6
5
A
B
- 2 -
• Push the SPRAY HOSE END (1) into FEMALE ADAPTER
(2) and slide down locking collar to secure connection.
• Orient solenoid valve with the orientation label facing up.
• Push SOLENOID ASSEMBLY (3) connection “B” into the
HOSE CONNECTOR (4) as shown, and slide down
locking collar towards SOLENOID ASSEMBLY (3) to
secure connection.
• Push SOLENOID ASSEMBLY (3) connection “A” into
other end of FEMALE ADAPTER (2) as shown, and slide
locking collar towards SOLENOID ASSEMBLY (3) to
secure connection.
• With HAND SPRAY (5) seated in SPOUT (6), install
WEIGHT (7) at labeled area onto HOSE (8), secure
with SCREW (9).
• Important: Make sure you pull out hose and check to
see that it moves freely and is not obstructed by supply
hoses, solenoid valve or items in the bottom of the
cabinet.
Slide
locking
collar to
secure
UP
Locking
Collar
IMPORTANT: Do not
use sealent on threads
1
2
3
COLD
HOT
(3) INLINE
FILTER

5ELECTRICAL CONNECTIONS – BATTERY HOLDER
ELECTRICAL CONNECTIONS - SENSOR TO SOLENOID
4
M965802 Rev.1.2 (11/18)
5
9
67
1
12
3
11
2
UP
• Connect SOLENOID CONNECTOR (12) with
the sensor connector from the faucet with the
yellow tag stickers, secure this connection by
installing inside the CONNECTORS HOUSING
(3) as shown and lock by twisting the white
end pieces.
NOTE: Use Qty. (4) AA Alkaline type
batteries only.
- 3 -
• Identify desired BATTERY HOLDER (7) location.
Battery holder should be located so batteries can
be easily accessed, with in 6ft of the faucet hook
and loop (black strip) (5).
• Attach CABLE MOUNTS (4) along the inside
of the kitchen cabinet walls positioning them
accordingly as shown. Wipe clean surfaces
before attaching CABLE MOUNTS (4).
• Attach ‘HOOK TO LOOP’ FASTENER (black strip)
(5) to the back side of the BATTERY HOLDER (7)
and attach ‘HOOK TO LOOP’ FASTENER (black
strip) (5) on desired location inside the kitchen
cabinet. Wipe mounting surface clean before
attaching ‘HOOK TO LOOP’ FASTENER (black
strip) (5).
• Secure longer SENSOR CABLE (6) to the CABLE
MOUNTS (4) using the WIRE TIES (8) provided.
• Ensure that the BYPASS KNOB (10) on the
SOLENOID ASSEMBLY (1) is in the “OFF”
position.
• With the SLIDING DOOR (11) in the open
position, connect the BATTERY HOLDER CABLE
(9) to the other end of the long SENSOR CABLE
(6), that is coming out of the faucet. The sensor
will start to blink several times and then stop.
5
9
67
1
12
10
8
4
2
UP
11

M965802 Rev.1.2 (11/18)
7
- 4 -
FAUCET OPERATION – AUTOMATIC MODE, MANUAL MODE AND FEATURES
2
3
1
OPEN
CLOSED
Hot
Cold Open
Closed
Automatic Mode
• Make sure the SLIDING DOOR (1) and HANDLE (2) are in the open position.
• To turn on the water, momentarily place your hand within 3"of the
SENSOR (3).
• To turn off the water, momentarily place your hand again within 3"of the
SENSOR (3).
Manual Mode
• Close the SLIDING DOOR (1) and use the HANDLE (2) to turn on and off
the water.
FEATURES
Safety Timer
• The faucet will automatically turn off the water after 5 minutes of
continuous use. Momentarily place you hand in front of the sensor to
turn on the water.
Low Battery Indication
• The sensor will start to blink constantly every second. This is the indication
that the batteries are low in power. Replace the batteries with Qty. (4) AA
Alkaline type batteries.
• Battery lifetime is approximately 1 year under normal use.
1
REMOVE
2
3
CHECK
CONNECTIONS
FOR LEAKS
6
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check connections for leaks.
• With HANDLE (1) in “off” position, unthread SPRAY (3)
from HOSE (2).
• Operate HANDLE (2) up and down, left and right to ush
water lines thoroughly.
• Replace SPRAY (3) onto HOSE (2).
• Operate HAND SPRAY and check connections for leaks.
TEST INSTALLED FAUCET & CHECK CONNECTION FOR LEAKS

8
M965802 Rev.1.2 (11/18)
SPRAY OPERATION
• With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch
from stream to spray.
• Press and hold PAUSE BUTTON (5) to temporarily stop ow from SPRAY
(3). Release PAUSE BUTTON (5) to resume ow from SPRAY (3).
9
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE:
- 5 -
Battery needs replacement:
• Sensor will start to blink continuously every second.
This is the indication that the batteries are low in power.
• Replace batteries in battery holder with Qty (4) AA alkaline
type batteries.
• Batteries last approximately one year.
• Always change all 4 batteries. Failure to replacing all 4
batteries at the same time may cause faucet electronics
to not work properly.
Reduced or distorted ow:
Debris or dirt accumulating at inlet or AERATOR MAY
CAUSE REDUCED OR DISTORTED FLOW.
A) Clean inline lter at inlet hoses.
B) Turn hot and cold water supply off. Open valve in mixed
position for two seconds to relief pressure close valve.
C) Disconnect inlet hoses at stop valve and clean screen
lter. If necessary remove inline lter and rinse at another
water source.
Aerator Clean Out
• AERATOR may accumulate dirt causing distortion and
reduced water ow. Remove AERATOR by using the
AERATOR KEY (9) and rinse to clear any debris.
• Clean out the SCREEN (10) by removing
SPRAY HEAD (11).
Power failure (manual bypass):
• In the event of a power failure, turn the BYPASS KNOB (1)
on the SOLENOID ASSEMBLY (2) to the “ON” position.
The faucet will be in MANUAL MODE (see section 5) and
the HANDLE (3) can be used to turn on and off the water.
SERVICE
7a
1
2
9
10
11
6
8
6a
7
1
2
4
5
9
3
INLINE FILTER
STREAM (AERATOR)
SPRAY
5
3
4

M962146-0070A
MOUNTING KIT
M970249-0070A
WEIGHT M964483-0070A
CABLE TIE &
CABLE MOUNT
M970109-0070A
BATTERY PACK
M951483-0070A
CARTRIDGE
M918511-0070A
CARTRIDGE SCREWS
M907315-YYY0A
ESCUTCHEON CAP
M970266-YYY0A
HANDLE KIT
M954486-0070A
SOLENOID
ASSEMBLY
M921403-0070A
FEMALE ADAPTER
AND SLEEVE
1660152-XXX
ESCUTCHEON AND SEAL
(OPTIONAL)
M950413-YYY150A
SPRAY ASSEMBLY
M911793-0070A
SEAL
M950415-0070A
SPRAY WITH HOSE
M970376-YYY0A
BUTTON &
SCREW KIT
M950019-0070A
INLINE FILTER
REQUIRES (2)
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M965802 Rev.1.2 (11/18)
Replace the “YYY” with
appropriate nish code
POLISHED CHROME 002
STAINLESS STEEL 075
MODEL NUMBER
AVERY™
ELECTRONIC PULL-DOWN
KITCHEN FAUCET
- 6 -
4901.380