American Standard GREEN TEA 7010.801 User manual

M968598 Rev.1.4
6
5
MOUNTING
SURFACE
SPOUT BASE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT (1), CABLE CONNECTOR (2) and SPOUT HOSE (3) through center hole,
making sure the SEAL WASHER (4) is properly seated in spout base.
Assemble RUBBER WASHER (5), LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the
mounting hole.
Tighten LOCKNUT (6) firmly. Fig. A.
Tighten LOCKNUT (9) with WRENCH (12) (supplied) to secure VALVE
BODY (11). Repeat above steps for opposite VALVE BODY (11a).
Install LOCKNUT (9) and RUBBER WASHER (10) onto VALVE BODY (11).
From under side of mounting surface, install VALVE BODY (11) through valve
mounting hole. Threads of VALVE BODY (11) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (8)
onto VALVE BODY (11) until snug against internal stop. If necessary,
adjust LOCKNUT (9). Align as shown.
1
1A
7010.801
Certified to comply with ANSI A112.18.1
Installation
Instructions
GREEN TEA
Spread Lavatory Faucet with
INSTALL SPOUT
INSTALL VALVE BODIES
4
3
12
8
7
10
9
11
11a
8
7
10
9
Place RUBBER RING (7) into DECK ADAPTER (8).
11
5/16'' MIN.
7
Speed Connect™ Drain
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
Tubing Cutter
Fig. A.
Fig. B.
1
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
1
2

M968598 Rev.1.4
2
6
POP-UP KNOB (1) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB Fig. A.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
4
3
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
2
3
3
1
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
INSTALL DRAIN FROM
BELOW FIXTURE 5
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
4
Fig. A. Fig. B.
Fig. A. Fig. B.
2
DRAIN
OUTLET
1
3
4
REAR OF SINK
DRAIN
BODY
4
WHITE FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
Fig. B.
DOWN

M968598 Rev.1.4
9WATER SUPPLY, TEE, SPOUT AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then refer
to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
8
3
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
Fig. A.
ATTACH CABLE CONNECTOR
7
2
1
Fig. B.
1-1/4” O.D.
HOT
HOT
COLD
COLD
FERRULE
1-1/4"O.D. TAILPIECE
COMPRESSION
NUT
COUPLING
NUT
FLEXIBLE
SUPPLIES
1
1a
3/8 O.D.
BULL-NOSE
RISERS
1/2" PIPE
THREAD
3/8 COMPRESSION
CONNECTION
2
3
9a
9
5
WASTE
OUTLET
6
2
1
Connect water supply to VALVE BODIES (1,1a) with 1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use
adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing
cutter to cut to proper length.
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
Connect male thread of PULL-OUT HOSE (4) to COUPLING
NUT (5) on TEE (6). Tighten with wrenches.
Thread COUUPLING NUTS (9, 9a) on TEE HOSES to valve
body inlets. Tighten with adjustable wrench.
Snap small end of HOSE HOLDER (7) between TEE (6)
and COUPLING NUT (5). Then snap HOSE HOLDER (7)
to SHANK (8).
Connect 1-1/4" O.D. tailpiece on POP-UP DRAIN
to waste outlet.
INSTALL WEIGHTS
Attach WEIGHTS (10) to HOSE (4) at bottom of
loop in Hose (4) as shown.
10
4
7
4
8
“P” TRAP

M968598 Rev.1.4
10 INSTALL HANDLES
CHECK DRAIN CONNECTIONS
11
12
14
TEST INSTALLED FITTING
SERVICE
2
90˚
If spout drips, operate handles several times from
OFF to ON position. Do not force - handles turn only 90˚.
3
2
4
1
4
5
Turn valve to OFF position
Thread HANDLE BASE (1a) counter clock-wise until loose.
Pull HANDLE (1) “UP” firmly to release from
ADAPTER (2).
Remove SPRING CLIP (3). Lift STOP WASHER (4),
turn 90˚ and replace. Replace SPRING CLIP (3).
Re-install HANDLE ASSEMBLY (1).
To change direction of handle:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
CARE INSTRUCTIONS:
1
2
4
4a
5
3
TOP
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. Fig. A. Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4). Push
LEVER HANDLE ASSEMBLY (4) down onto ADAPTER (1).
Thread base of LEVER HANDLE ASSEMBLY (4a) onto DECK
ADAPTER (5) until snug against mounting surface. Fig. A.
1
1a
i
n
s
t
a
l
l
“P” TRAP
WASTE
OUTLET
COLD
HOT
3
2
2
3a
OFF
1
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3) using KEY (3a) supplied.
Operate both HANDLES (1) to flush water lines thoroughly.
Replace AERATOR (3).
Operate POP-UP KNOB (4) and fill lavatory with water.
Check that DRAIN STOPPER (5) makes a good seal
and retains water in SINK. If DRAIN STOPPER (5)
does not seal properly, refer to Troubleshooting
section in these instructions.
Release POP-UP KNOB (4) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
r
e
m
o
v
e
OPTIONAL SPOUT LOCKING FEATURE
The Pull-Out SPOUT (1) can be locked to the SPOUT BASE (2) if desired.
To secure the Pull-Out SPOUT (1) to SPOUT BASE (2), tighten the SET
SCREW (3) clockwise in the back of the SPOUT BASE (2) with a 2.5mm
hex wrench.
2.5mm HEX
WRENCH
13
12
3
15

M968598 Rev.1.4
Fig. F.
5
Speed Connect™ Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.Fig. A.
REMOVE
CAM
Fig. E.
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
STOPPER REMOVAL PROCEDURE
2
1
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
LIFT-KNOB
STOPPER
Fig. C. DOWN

M968598 Rev.1.4
LOOP TOWARD
REAR OF SINK
Fig. G.
LOGO
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode
(Vandal Proof)
Unlocked Mode
DRAIN
6
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
Fig. G.
LOGO
DRAIN
LOOP TOWARD
FRONT OF SINK
180˚

M968598 Rev.1.4
7
Spread Lavatory Faucet
with Speed Connect™ Drain
M961634-0070A
VALVE MTG. KIT
994053-0070A
CARTRIDGE
M962619-0070A
DECK ADAPTER KIT
024220-0070A
SUPPLY NUT
918049-0070A
ADAPTER
A918555-0070A
HANDLE SCREW
M922990-0070A
AERATOR
M922380-0070A
AERATOR KEY
CHROME
SATIN NICKEL
STAINLESS STEEL
002
295
075
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2007
M950171-YYY0A
HANDLE KIT
M921371-0070A
ADAPTER
M962552-0070A
CAM ASSEMBLY
M952425-YYY0A
DRAIN ASSEMBLY
M962544-YYY0A
STOPPER
ASSEMBLY
M962457-YYY0A
FLANGE
ASSEMBLY
M962458-0070A
DRAIN MOUNTING KIT
A919661-0020A
TAILPIECE
M922872-0070A
CAM SEAT INSERT
M913207-0070A
TAILPIECE INSERT
M919660-0020A
6” TAILPIECE
(NOT INCLUDED
WITH FAUCET)
IN MEXICO 01-800-839-1200
GREEN TEA
7010.801
M962777-YYY0A
SPOUT & HOSE
M922375-0070A
HOSE HOLDER
A911819-0070A
SEAL
M950195-0070A
TEE & HOSE S/A
M962620-YYY0A
LIFT ROD & KNOB
M964890-0070A
CABLE ASSEMBLY
M962621-0020A
PULL OUT HOSE
& WEIGHT
M961634-0070A
SPOUT MTG. KIT
A953051-0070A
CHECK VALVE
A912692-0070A
SEAL
A953051-0070A
CHECK VALVE