American Standard Portsmouth 4285.051 User manual

HIGH ARC SINGLE CONTROL
KITCHEN FAUCET WITH SPRAY
4285.051
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Installation
Instructions
Certified t o comply with ANSI A112.18.1M
Plumbers' Putty or CaulkingAdjustable WrenchPhillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
Turn off water at
main supply.
CAUTION
PORTSMOUTH™
M965473 Rev. 1.1
BA
SINK OR
MOUNTING
SURFACE
RING BASE
9
10
3
2
1
9
PUTTY
SPOUT BASE
2
3
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (7) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
Make certain the SEAL (9) is properly seated in recess of spout base.
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert all HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and
mounting surface. Do not use putty.
4
5
6
4
5
6
77

M965473 Rev. 1.1
Place the SPRAY HOLDER (1) into the appropriate mounting hole.
Assemble the SPRAY HOLDER WING NUT (2) onto the shank of
SPRAY HOLDER (1) from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (3) with PIPE CAP (4).
3INSTALL SPRAY HOLDER
1
5
4
2
TEST INSTALLED FAUCET
Move HANDLE into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and
activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) to "off" position and replace
AERATOR (1).
6
3
4
CONNECT HOSE SPRAY
Feed SPRAY HOSE (5) through SPRAY
HOLDER (1) and attach COUPLING NUT (6)
of HOSE (5) to SPRAY HOSE CONNECTION (3)
on valve body. Tighten COUPLING NUT (6) firmly.
2
SPRAY HOSE
CONNECTION
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
CHECK CONNECTIONS
FOR LEAKS
3
12
1
2
COLD
HOT

SERVICE
5
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
7
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Reverse procedure to reinstall SPOUT (9).
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
Clean MANIFOLD (7) and CARTRIDGE (6) ports.
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M965473 Rev. 1.1
REMOVEINSTALL
Spout leakage. If fitting leaks above or below spout RETAINING COVER (8) remove SPOUT (9) as follows
and check SPOUT O-RING. First turn off water supply.
Unthread spout RETAINING COVER (8).
Remove SPOUT (9) by pulling up gently while moving SPOUT (9) side to side.
Check SPOUT O-RING (10) for damage. Replace if necessary.
The DIVERTER (11) can be cleaned by unthreading from faucet body. Rinse the DIVERTER (9) clean and
thread DIVERTER (11) back into faucet body.
1
3
12
9
8
11
10
2
4
5
6
7
REMOVE
RETAING RING
CLIP RING
INSTALL
Reduced flow. If the flow gradually reduces over a
number of months, the AERATOR (12) may have
collected debris.To clean, remove AERATOR (12)
and rinse with water and remove any debris. Turn
on faucet to wash any debris out of the faucet.
Thread AERATOR (12) back into spout.
Operate faucet.

A911836-0070A
SEAL
M964065-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
M965473 Rev. 1.1
MODEL NUMBER
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the YYY with
Appropriate finish code
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2013
HOT LINE FOR HELP
4285.051
PORTSMOUTH™
M953040 -YYY0A
SPRAY HOLDER
M953668-YYY0A
HANDSPRAY & HOSE
M964396-YYY0A
HANDLE KIT
M964397-0070A
BUTTON AND
SCREW KIT
M907315-YYY0A
ESCUTCHEON CAP
M951483-0070A
CARTRIDGE
M964509-0070A
RETAINER & SEAL KIT
M953056-0070A
DIVERTER
M918511-0070A
CARTRIDGE SCREWS
M907986-YYY0A
RETAINING COVER
M910288-0070A
AERATOR
M911231-YYY0A
AERATOR RING
HIGH ARC SINGLE CONTROL
KITCHEN FAUCET WITH SPRAY
M907989-YYYOA
MOUNTING RING KIT