American Standard Reliant+ Lavatory Faucets 2385.R User manual

LAVATORY FAUCETS
POP-UP DRAIN
Installation
Instructions
78523C
Printed in U.S.A.
2385.R SERIES
2385.W SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
U.S. PATENT NO. 4,294,289;
Turn off hot and cold water
supplies before beginning.
CAUTION
1
Printed
on
Recycled
Paper
SUPPLY
NUT HEX NUT
AERATOR
U- CHANNEL
POP-UP
ROD
PUTTY
PLATE
BOLT
FAUCET INSTALLATION
SINK
1/2 GPM
FLOW DEVICE
KEY
CARTRIDGE
SET SCREW
CAP
RETAINER
CAP
HANDLE
CARTRIDGE
SCREWS
HANDLE
BUSHING
SEALS
CLIP
THUMBSCREW
STOPPER
DRAIN
FLANGE
FLANGE
GASKET
GASKET
WASHER
NUT
DRAIN
BODY
EXTENSION
PIVOT
ROD
P0P-UP
ROD
UNDERBODY
SCREW
TM
SPACER
U- CHANNEL
HEX NUT
HOT LIMIT
STOP
PUTTY
PLATE
Put U-CHANNEL, SPACERS, if necessary and NUTS
onto BOLTS.
Place PUTTY PLATE on SINK. Push faucet supplies
and studs through deck holes.
Insert POP-UP ROD to assure proper clearance when
faucet is assembled to the sink.
Position FAUCET on SINK.
Tighten HEXNUTS.

CARTRIDGE
SCREWS
HANDLE
BUSHING
Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1993
C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
SERVICE
6
CONNECT SUPPLIES
Carefully bend copper supplies to meet water supply lines using
the palms of the hands to avoid kinking.
Connect HOT water supply line to LEFT tube, and COLD water
supply line to RIGHT tube using appropriate connectors.
OR
2
TEST INSTALLED FAUCET
4
For vandal-resistant FLOW DEVICE, insert KEY teeth into
slots near outlet and turn.
Turn on water supplies and check connections for leaks.
Operate handle up and down, left and right to flush water lines
thoroughly.
Move handle down to "off" position and replace AERATOR or FLOW
DEVICE.
Remove HANDLE, CAP, HOT LIMIT STOP and CARTRIDGE.
Clean inlets and MANIFOLD.
Reassemble CARTRIDGE, alternately tightening screws. Replace
HOT LIMIT STOP , CAP and HANDLE. Check flow.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR. Clean AERATOR and FLOW
RESTRICTOR. Replace AERATOR.
If faucet drips, operate handle several times from "off" to "on".
Do not apply excessive force.
Clogged CARTRIDGE inlets may cause reduced flow in "full
on" hot or cold. To clean inlets, first turn off water supply,
then:
78523C
Move handle down into "off" position and remove AERATOR.
AERATOR
CARTRIDGE
SET SCREW
CAP
RETAINER
CAP
SEALS
P0P-UP
ROD
HANDLE
HOT LIMIT
STOP
ADJUSTMENT WHEN
WATER IS TOO HOT ADJUSTMENT WHEN
WATER IS TOO COLD
PRY UPWARD TO UNLOCK
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY UPWARD TO UNLOCK
AND ROTATE CLOCKWISE
"A" "B"
FRONT FRONT
By restricting handle rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP reduces risk of accidental scalding. To set the maximum
hot water temperature of your RELIANT faucets, all you need
to do is adjust the setting on the HOT LIMIT SAFETY STOP.
HOT LIMIT STOP
5
Remove HANDLE, CAP and HOT LIMIT STOP. Follow "A" or "B"
to adjust maximum discharge temperature.
3INSTALL POP-UP DRAIN STOPPER
Thread LOCKNUT, WASHER and GASKET onto
DRAIN BODY.
Push DRAIN BODY down into trap.
Feed DRAIN BODY up through SINK. Place FLANGE
GASKET over BODY and thread FLANGE FULLY
onto BODY.
Tighten LOCKNUT firmly, keeping the PIVOT ROD
pointed towards the back of the SINK.
Drop STOPPER into DRAIN BODY.
Position EXTENSION ROD onto POP-UP ROD and
tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD by squeezing
ends together while sliding.
Insert PIVOT ROD into second or third hole in EXTENSION
and reassemble CLIP. (EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION and
tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
FLANGE
GASKET
WASHER
LOCKNUT
DRAIN
BODY TRAP
CLIP
THUMBSCREW
POP-UP ROD
CLIP
PIVOT
ROD
EXTENSION
ROD
TRAP
EXTENSION
ROD