American Standard 1340M Series User manual

1340M SERIES INCLUDES BELOW DECK
MIXING VALVE WITH STRAINER
1340 SERIES FOR COLD AND TEMPERED
SUPPLIES
SINGLE TAP PUSH BUTTON FAUCET
Installation
Instructions
012692D
1340 SERIES
1340M SERIES
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully
before you begin.
Certified to comply with ANSI A112.18.1M
U.S. PATENT NOS.
ASSEMBLING MOUNTING KIT
WARNING: SUPPLY INLET MUST BE FILTERED WITH A 60 MESH SCREEN.
USE AMERICAN STANDARD MIXING VALVE WITH STRAINER OR COMMERCIAL 60 MESH STRAINER.
MOUNTING FITTING
FOR 1340 SERIES ONLY
2
3
HANDLE
SPRING
LEVER
VALVE
CARTRIDGE
HANDLE
RETAINER
BODY
METERING FAUCET
Thread (3) SCREWS into LOCK RING.
SCREWS should extend half-way thru RING.
Install faucet through the ESCUTCHEON being sure the
rubber GASKET is between the FAUCET and the
ESCUTCHEON.
Install brass WASHER and turn LOCK-RING onto SHANK.
Tighten (3) SCREWS in the LOCK-RING to secure fitting.
Install RISER TUBE (not included) and tighten
SUPPLY NUT.
Connect RISER TUBE to COLD or TEMPERED water
supply.
Warning; 60 MESH STRAINER required for supply water.
AERATOR
KEY
GASKET
ESCUTCHEON KIT
(OPTIONAL)
WASHER,
BRASS
DECK
LOCK-RING
AND SCREWS
RISER TUBE
(NOT INCLUDED)
SUPPLY
NUT
PUSH
SET SCREWS
RETAINING
RING
LOCK RING
SCREWS
Turn off hot and cold water supplies before beginning.
1340M SERIES
1340 SERIES
CAUTION
1ASSEMBLING ESCUTCHEON KIT (OPTIONAL)
Peel off paper backing from PADS and stick both
PADS to underside of ESCUTCHEON about 1/4"
from ends.
Peel off paper backing from WASHER and stick
WASHER into circular groove of SUPPORT PLATE.
Place SUPPORT PLATE in center
of ESCUTCHEON with WASHER visible.
Apply a bead of PUTTY around
the inside of ESCUTCHEON edge.
Turn ESCUTCHEON over and
center it with SUPPORT
PLATE over center hole
of sink deck.
PAD
PUTTY
SUPPORT
PLATE
PAD
ESCUTCHEON
WASHER
Connect FLEXIBLE FAUCET
SUPPLIES (1/2" faucet cone
on one end, 3/8" compression
on the other) to the MIXING
VALVE INLETS and the
hot/cold wall stops.
The FLEXIBLE FAUCET
SUPPLIES are NOT
included. Turn on WALL
STOPS and check
for leaks.
MIXING
VALVE
STRAINER
MIXING
VALVE
INLETS
FLEXIBLE
FAUCET
SUPPLIES
WALL
STOPS
HOT
MIXING
VALVE
ADJUSTMENT
COLD
FOR 1340M SERIES
With WALL STOPS open
and water flowing, adjust
MIXING VALVE to temper
water.
HOTTER
COLDER
MIXING
VALVE
MIXING
STRAINER
VALVE
ASSEMBLY FILTER
SCREEN
DUCK
BILL
CHECKS

10 sec.
minimum
Lift off retaining
ring then slide
out lever
horizontally.
Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1996
C
Press down to start.
TO OPERATE
4
Cycle time is factory set but can
be changed as shown.
Stop
Automatic
TO SERVICE
5
SPRAY INSTALLATION/REMOVAL
6
TO remove HANDLE use a 3/32" ALLEN WRENCH to loosen three set screws in the HANDLE
as shown in Figure A.
Remove VALVE CARTRIDGE for cleaning or replacement, see in Figure B.
Reassemble in reverse order, Figures C & D.
ROUGHING-IN DIMENSIONS
7
All dimensions are approximate and for reference only.
Use included key to install SPRAY into spout end.
25mm
(1" MAX)
48mm
(1-55/64)
111mm
(4-3/8)
45mm
(1-3/4DIA.)
90mm
(3-9/16)
30°
53mm
(2)
012692D
Start +
-
40 sec.
Retaining
Ring
Lever
21mm
(53/64 DIA.)
1/2"-14
NPSM
THREAD
PUSH
7 sec.
Figure A Figure B Figure C
Figure D
TIGHTEN
SET SCREWS
TIGHTEN VALVE
CARTRIDGE
REMOVE
HANDLE REPLACE
VALVE
CARTRIDGE
3/32"
ALLEN
WRENCH
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)