American Standard Standard 4271 User manual

by
COLLECTION
™
THE
Plumbers' Putty or CaulkingAdjustable WrenchChannel Locks
TOOLS REQUIRED
1
M9684 3
INSTALL FAUCET and SPRAY
INSTALL FAUCET
INSTALL SPRAY
4271
Certified to comply with ASME A 2. 8. M
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read
these instructions carefully before you begin.
Installation
Instructions
Top Mount Kit hen Fau et
Place FAUCET ( ) in postion on sink or mounting surface.
Assemble and tighten LOCKNUTS (2) from underside of
sink or mounting surface. Hand tighten to secure FAUCET ( ).
FAUCET ( ) can be installed with or without HAND
SPRAY (3). To install FAUCET ( ) with HANDSPRAY (3)
thread PIPE CAP (4) counter-clockwise and remove.
Place the HOLDER (5) into the appropriate mounting
hole. Assemble the SPRAY HOLDER WING NUT (6)
onto the shank of SPRAY HOLDER (5) from below
and tighten.
Feed SPRAY HOSE (7) through HOLDER (4) so SPRAY (3)
sits in HOLDER (5).
From underneath sink, attach COUPLING NUT (8) of SPRAY
HOSE (7) to HOSE SHANK (9). Tighten COUPLING NUT (8)
firmly.
Turn off hot and old water supplies before beginning.
CAUTION
Basin Wrench Tubing Cutter
1
2
SINK OR
MOUNTING
SURFACE
(HAND TIGHTEN)
7
6
3
4
5
9
28

M9684 3
3TEST INSTALLED FITTING
With HANDLES ( ) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate both HANDLES to flush water lines thoroughly.
Rotate SPOUT (4) in both directions.
Replace AERATOR (3).
Direct SPRAY (5) into sink and activate. Check hose
connections for leaks.
Connect water supply to FAUCET ( ) with /2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3 ).
Use adjustable wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply when bending.
Use tubing cutter to cut to proper length.
MAKE WATER SUPPLY CONNECTIONS
2
FERRULE
COUPLING NUT
1
2
1
3
2
4
5
1
1
3
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
5CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.
41
2
4
5
6
SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP ( ) and remove HANDLE SCREW (2).
Pull off HANDLE (3).
Pull off STEM ADAPTER (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (6) and STEM ADAPTER (4).
Reinstall HANDLE ASSEMBLY ( ,2 & 3).
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
3
90°

M9684 3
Replace the "YYY" with appropriate finish code
002
295
CHROME
SATIN
M953040-YYY0A
SPRAY HOLDER
M953667-YYY0A
HANDSPRAY & HOSE
M923052-0070A
PUTTY PLATE
994053-0070A
VALVE
M918049-0070A
ADAPTER
66070-YYY0A
AERATOR
M962265-YYY0A
SPOUT KIT
A918572-0070A
HANDLE SCREW
M962243-0070A
HANDLE ASSEMBLY
M961162-0070A
INDEX BUTTON (HOT)
M961163-0070A
INDEX BUTTON (COLD)
923012-0070A
SPOUT CLIP
073542-0070A
O-RING
060464-0070A
DIVERTER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
-800 442- 902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA -800-387-0369 (TORONTO -905-306- 093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
4271
TOP MOUNT
KITCHEN FAUCET
by
COLLECTION
™
“”
THE
065800-0070A
ATTACHMENT NUT
024220-0070A
SUPPLY NUT