American Standard Corner Minette 0451.001 User manual

M17
© 2008 AS America Inc. Revised 2/08
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen
❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies with Stop:
❏ 1-1/4" Trap:
❏ Nipple:
* See faucet section for additional models available
CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
CORNER MINETTE™ WALL-HUNG LAVATORY
• Wall-hung corner sink
• Vitreous china
• Front overow
• Supplied with 2 wall hangers
• Faucet ledge
Shown with 2000.101 Ceramix faucet
(not included)
❏ 0451.021 Faucet holes on 102mm (4") centers
❏ 0451.001 Single center faucet hole
Nominal Dimensions:
279 x 425mm
(11" x 16-3/4")
Bowl sizes:
311mm (12-1/4") wide,
219mm (8-5/8") front to back,
133mm (5-1/4") deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixture
SEE REVERSE FOR ROUGHING-IN DIMENSIONS

M18
© 2008 AS America Inc.
CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
FINISHED
FLOOR
SUPPLIES
AS REQ'D.
464mm
(18-1/4)
*
178mm
(7-1/2)
165mm
(6-1/2)
279mm
(11)
165mm
(6-1/2)
152mm
(6)
127mm
(5)
102mm
(4)
127mm
(5)
425mm
(16-3/4)
C/L OF C.W. SUPPLY
C/L OF WASTE
C/L OF HANGER
FINISHED WALL
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
HANGER
260mm
(10-1/4)
*
178mm
(7)
178mm
(7) 787mm
(31)
108mm
(4-1/4)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
C/L OF HANGER
C/L OF H.W. SUPPLY
FINISHED
FLOOR
SUPPLIES
AS REQ'D.
464mm
(18-1/4)
*
178mm
(7-1/2)
165mm
(6-1/2)
279mm
(11)
165mm
(6-1/2)
152mm
(6)
127mm
(5)
425mm
(16-3/4)
C/L OF C.W. SUPPLY
C/L OF WASTE
C/L OF HANGER
FINISHED WALL
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
HANGER
260mm
(10-1/4)
*
178mm
(7)
178mm
(7) 787mm
(31)
108mm
(4-1/4)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
C/L OF HANGER
C/L OF H.W. SUPPLY
0451.021 4" CENTER FAUCET HOLES
0451.001 CENTER HOLE FAUCET
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P” TRAP
ARE SUGGESTED.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
Revised 2/08