AMERICH Airbath User manual

User Guide
INSTALLER: To be removed for use by the occupant

operating instructions
Airbath®
On/O Key
1st Press: The blower starts at 50%
2nd Press: The blower stops
System Speed
1st Press: Press and hold to increase the blower speed, release
pressure at the desired speed.
2nd Press: Press and hold to decrease the blower speed, release
pressure of the desired speed.
Wave Mode
1st Press: Wave - Speed will vary gradually from maximum to
minimum.
2nd Press: Pulse - Speed will go directly to minimum and then
straight back to maximum.
3rd Press: Returns to maximum speed.
Water Level Sensor
If water falls below water level sensor while blower is on, an automatic purge
will initiate in thirty minutes to dry the air channels.
Automatic Purge
Thirty minutes after the water falls below the water level sensor the blower
will start again for a one-minute purge cycle allowing piping
to thoroughly dry.
Always use dedicated outlets for each power supply.**
2
AIRBATH® + LIGHT
On/O Key
1st Press: The blower starts at 50%.
2nd Press: The blower stops.
While the blower functions press and hold
3 sec.: Wave - Speed will vary gradually from maximum to
minimum
6 sec.: Pulse - Speed will go directly to minimum and then
straight back to maximum.
System Speed
1st Press: Press and hold to increase the pump speed, release
pressure at the desired speed.
2nd Press: Press and hold to decrease the pump speed, release
pressure of the desired speed.
Chromotherapy
1st Press: Auxiliary equipment
ON > White
2nd Press: Slow rainbow cycle
3rd Press: Fast rainbow cycle
4th Press: Turquoise, Blue, Magenta, Red, Orange, Yellow,
Green
Return to slow rainbow cycle
Press and Hold 1 sec.: Auxiliary equipment OFF
Automatic Purge
*(only available with models equipped with Airbath
®
)
Thirty minutes after the water falls below the water level sensor the blower
will start again for a one-minute purge cycle allowing piping to thoroughly
dry.
Always use dedicated outlets for each power supply.**
**Note: Blower hose for AirBath Systems is shipped loose:
1) Remove red caps from blower and check valve.
2) Attached grey hose to blower and check valve.
3) Tighten clamp around each end.

3
operating instructions
The Builder Series whirlpool is equipped with an On/O Button (ll tub until
the highest jet is covered by at least 2”of water. Do not run pump without
water in the tub.)
1. Press the Button to start the pump.
2. Press a second time to stop the pump. The Control Box is manufactured
with a 10 minute timer that will turn o the unit automatically. To
continue your bath, simply push the Button to repeat the cycle.
Note: If OPTIONAL built in water level sensor is installed on your tub, ll the
tub with water until the water level sensor pad is covered. Now you can press
the Button to start the pump.
BUILDER SERIES
Always use dedicated outlets for each power supply.**
GFCI
outlet
control
box
clear
tube tub
on/o
buon
pump
PLATINUM SERIES O R
LUXURY SERIES + LIGHT
Starts pump Stops Pump
Always use dedicated outlets for each power supply.**
Chromotherapy
1st Press: Auxiliary equipment ON > White
2nd Press: Slow rainbow cycle
3rd Press: Fast rainbow cycle
4th Press: Turquoise, Blue, Magenta, Red,
Orange, Yellow, Green
Return to slow rainbow cycle
Press and Hold 1 sec.: Auxiliary equipment OFF
Water Level Sensor
If water falls below water level sensor while blower is
on, the system will turn OFF.
Always use dedicated outlets for each power supply.**
1. Press the Button to start the pump.
2. Press a second time to stop the pump. The Control Box is
manufactured with a 20 minute timer that will turn o the
unit automatically. To continue your bath, simply push the
Button to repeat the cycle.
Water Level Sensor
If water falls below water level sensor while pump is on, the system will
turn OFF.
LUXURY SERIES

Blower On/O
1st Press: The blower starts at 50%
2nd Press: The blower stops.
Blower System Speed
1st Press: Press and hold to increase the blower speed, release
pressure at the desired speed.
2nd Press: Press and hold to decrease the blower speed, release
pressure at the desired speed.
Blower Wave Mode
1st Press: Wave - Speed will vary gradually from maximum to
minimum.
2nd Press: Pulse - Speed will go directly to minimum and then
straight back to maximum.
3rd Press: Returns to maximum speed.
Pump On/O
The pump starts The pump stops
Chromotherapy
1st Press:
Auxiliary equipment ON > White
2nd Press: Slow rainbow cycle
3rd Press: Fast rainbow cycle
4th Press: Turquoise, Blue, Magenta, Red, Orange, Yellow, Green
Return to slow rainbow cycle
Press and Hold 1 sec.: Auxiliary equipment OFF
Water Level Sensor
The system will turn OFF if the water level falls below the water level sensor
while pump is on.
If water falls below water level sensor while blower is on, an automatic purge
will initiate in thirty minutes to dry the air channels.
Automatic Purge
Thirty minutes after the water falls below the water level sensor the blower
will start again for a one-minute purge cycle allowing piping to thoroughly
dry.
Each system will automatically stop after 20 minutes.
COMBO SERIES + LIGHT
operating instructions
Always use dedicated outlets for each power supply.**
IMPORTANT: Keep these instructions with the Americh Installation Instructions. These operating instructions are for units with systems. All installation, warnings,
warranties, and other such information can be found in the Americh Installation Instructions. Go to www.americh.com for additional copies.
listed by
in compliance with
ANSI Z124.1 - 1995 ANSI A112.19.7 - 1987
ANSI A112.19.8 - 1987
City of Los Angeles M980036 and M820132
Always check www.americh.com for the most updated installation instructions.
©10/17
**Note: Blower hose for AirBath Systems is shipped loose:
1) Remove red caps from blower and check valve.
2) Attached grey hose to blower and check valve.
3) Tighten clamp around each end.
Manufacturer recommends the use of Jet Fresh®or a similar system cleaning solution to maintain your whirlpool or Airbath®System.