Ameriwood HOME 2456339COM User manual

2456339COM
End Table
B342456339COM0
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Follow Ameriwood Home
Tube
You
Date of Purchase ___ / ___ / ___
Lot Number:
Do Not Return This Product!
Contact our customer service team for help first.
Call: 1-800-489-3351 (toll free)
Monday-Friday 9am - 5pm CST
Visit: www.ameriwoodhome.com
Assembly Difficulty Meter
Easy Tough
- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall (if instructed to).
- Do Not allow children to climb on unit.
- Put heavy items on lower shelves or drawers.
WARNING

Contact Us!
Helpful Hints
2
ameriwoodhome.com
Do NOT return this product!
Contact our friendly customer service team first for help.
Call us!
1-800-489-3351
Monday-Friday
9am - 5pm CST
Visit ameriwoodhome.com to view the
limited warranty valid in the U.S. and Canada.
Assembly Tips
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
Tube
You
PEOPLE NEEDED FOR ASSEMBLY: 1-2

3
ameriwoodhome.com
Before You Start
P
Quick
Tip
Assembly
P
P
P
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Parts are labeled on the surface or edge of the part
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
P
12
34
Press parts together so CAM BOLT inserts
into edge hole.
Press CAM BOLT into hole. Press CAM LOCK into hole.
End hole
Using a screwdriver, turn the CAM LOCK clockwise to
lock the CAM LOCK and CAM BOLT into their holes
and fastening parts together.
Arrow to point towards end
hole in edge of part.

4
ameriwoodhome.com
Before You Start
Quick
Assembly
Tip
Please Note:
You may need to lightly tap the wood dowels into the holes during
your assembly process.

5
ameriwoodhome.com
Board Identification
Not actual size
Shelf Rail (x2)
32456339090
End Panel (x2)
32456339010 Top
32456339020
A
Bottom
32456339030
Left Front Leg
32456339050
Right Front Leg
32456339070
Left Rear Leg
32456339060
Right Rear Leg
32456339080
E
B
DFG
Back Panel
32456339120
C
H
I
JK
L
Base Side Rail (x2)
32456339110
Base Rail (x2)
32456339100
Adjustable Shelf
32456339040
Hammer Block
(piece of wood to use
to attach legs)

6
ameriwoodhome.com
Board Identification
Not actual size
L
A
B
C
D
E
F
G
H
I
J
K
A
I
K

7
ameriwoodhome.com
Part List
Actual Size
(x8)
#A22700
cam lock
2
3
1
(x8)
#A22710
cam bolt
(x10)
#A21670
wood dowel
(x8)
#A22795
locking sleeve
4
(x12)
#A22760
quicklock
7
(x8)
#A22790
locking bolt
8
(x2)
#A23030
confirmat
6
(x4)
#A80250
shelf support
5

8
ameriwoodhome.com
STEP1
(x8)
7
E
G
F
H
7
7
7
7
7
7
7
7

9
ameriwoodhome.com
STEP2
(x8)
Press locking sleeves (8) into edge holes as shown.
8
A
x2
8
8
8
8

10
ameriwoodhome.com
STEP3
3
3
(x1)
end view
Position and insert the locking bolts (7) of left rear leg (F) into edge holes of end panel (A) as shown.
Be sure both parts are positioned as shown. Place the hammer block on top of leg in each of the 2
locking bolt locations and give a firm strike to lock together. The locking bolt (7) will snap into the
locking sleeve (8).
IMPORTANT NOTICE: Once locked together, parts cannot be separated.
Note: A rubber mallet can be used in place of a hammer and hammer block.
A
F
Hammer Block
F
A
Holes on
this surface