AmerTac GRIPLIGHT BL-GRIP3-CP User manual

Mobile Phone Holder
Mobile phone holder is designed to t most phone sizes, including
many with a protective case (up to about 84mm or 3.3”). Simply pull
apart spring loaded jaws, place mobile phone in cradle and release
jaws. Holder will securely grip and hold your phone with soft grip
jaws. Position phone at virtually any angle by loosening locking nuts
on either end of the Angle Control Arm. Ball joints make positioning
easy and versatile with 360° rotation. Re-tighten locking nuts for a
secure installation.
CAUTIONS:
1.) Use caution when installing overhead to ensure product is
securely attached.
2.) Use only the size and type of batteries specied.
3.) Always purchase the correct size and grade of battery most
suitable for the intended use.
4.) Be sure to follow the correct polarity when installing the
batteries as indicated in the
battery compartment.
5.) Reversed batteries may cause damage to the device.
6.) Do not mix alkaline, standard (Carbon-Zinc), or rechargeable
(Nickel Cadmium) batteries.
7.) Replace all batteries of a set at the same time. Do not mix old
and new batteries.
8.) Clean the battery contacts and also those of the device prior to
battery installation.
9.) Do not dispose of batteries in re.
10.) Remove batteries if consumed or if product is to be left unused
for an extended period of time.
Where to install your GripLights
The GripLights are IP44 rated for indoor/outdoor use. It is protected
from solid objects greater than 1mm and from splashing water
from all directions. Caution: When used outdoors make sure slide
switch on Heavy Duty model is facing down. For long term outdoor
use install under eaves or other structures where GripLight is not
exposed to direct rain. When attaching to structures such as fences
or trees with Flexible Griping Tripod, be sure product is secure and
xed rmly to keep it from swaying in the wind so it will not fall on
people. With batteries installed product is heavy and serious injury
can occur.
Your GripLights may be installed on any metallic surface such as
the underside of a car hood, metal storage cabinets, metal poles,
etc. If no metal surface is available, you can also use the Metal Plate
accessory and afx that to any non-metal surface where a screw may
be used. Be sure to use proper plastic anchors in drywall or other
softer surfaces to properly secure your GripLight.
2 Motion Sensing LED Lights +
Mobile Phone Holder Owner’s Manual
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2019 AmerTac™
BO_TL_041_0320
GRIPLIGHT
GRIPLIGHTTM
Mounting Instructions Options for lights and mobile
phone holder
• Use Flexible Tripod to wrap legs around a
variety of objects or stand up on legs.
Simply attach tripod legs by screwing
into threaded hole on bottom of light or
mobile phone holder.
• Use magnets built into light or mobile
phone holder base to attach to any magnetic
metal surface or use included Metal Plate
accessory to attached to most non-metallic
surfaces. Includes a screw and plastic anchor.
Be sure Metal Plate accessory is rmly
attached to mounting surface to avoid injury or
product damage from falling.
• Position Flexible Griping Tripod legs to support product
standing independently.
Congratulations on your purchase of the Griplight portable task and worklight. It is perfect for camping, automotive, power
outage, travel, task lighting or other indoor/outdoor uses.

How to install batteries:
1.) Rotate body downward
2.) Pull battery cover by pushing the opening with thumb to
remove
3.) Insert (3) D Cell batteries(included)
4.) Push battery cover rmly to close
How to install batteries:
1.) Rotate body downward
2.) Pull battery cover by pushing the opening with thumb to remove
3.) Insert (3) AA Cell batteries(included)
4.) Push battery cover rmly to close
Heavy-Duty Griplight
Compact Griplight
Body Rotates 360°
Can be mounted with integrated magnet
Tripod Flexible legs can be wrapped around objects for mounting or used to stand and
directed where needed
Accessories Attach metal plate to any surface using with provided mounting screw
Body Rotates 360°
Can be mounted with integrated magnet
Tripod Flexible legs can be wrapped around objects for mounting or used to stand and
directed where needed
Accessories Attach metal plate to any surface using with provided mounting screw
Light Source LED
Wattage 3W
Battery (3) D Cell
Color 6000K
Battery Life
based on 20% of
original lumens
Mode 300 Lumens 175 Lumens 110 Lumens
Hours Stay ON 21 50 75
Days* 10 sec Auto 665 1300 1800
30 sec Auto 221 430 600
Motion Sensor Passive Infrared
Sensor Range 13 FT / 100°
Installation IP44 - Indoor / Outdoor
Dimensions Main Body: 4.25” x 3.70” x 5.50”, Tripod: 7.9”
Weight: 0.6 lbs (without batteries)
Light Source LED
Wattage 1W
Battery (3) AA Cell
Color 6000K
Battery Life based
on 20% of original
lumens
Mode 150 Lumens 75 Lumens
Stay ON 11 Hours
10 sec Auto 554 Days*
Motion Sensor Passive Infrared
Sensor Range 13 FT / 100°
Installation IP44 - Indoor / Outdoor
Dimensions Main Body: 3.60” x 3.15” x 3.95”, Tripod: 5.1”
Weight: 0.3 lbs (without batteries)
Three Modes of Operation:
OFF: Power is OFF
10sec: Lights turn ON when there is
no light for 10 seconds when it
senses motion
30sec: Lights turn ON when there is
no light for 10 seconds when it
senses motion
ON: Power stays ON
Two Modes of Operation:
Auto-Low / Off / High
Auto-Low: Lights turn ON when
there is no light for
10 seconds when it
senses motion
OFF: Power is OFF
HIGH: Light stays ON
Three Brightness Levels:
• 110 Lumens
• 175 Lumens
• 300 Lumens
Two Brightness Levels:
• 75 Lumens (only for AUTO-Low mode),
• 150 Lumens (only for STAY ON mode)
On/30sec/10sec/Off
Specications:
Specications:
Auto-Low / Off / High
*Based on 10 ON/OFF cycles per day
*Based on 10 ON/OFF cycles per day