AMG AMG4642ER User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
1
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
AMG4642ER
Instruction Manual
4 Channel Video Receive Unit with Ethernet for a
Multimode Fibre Link
The
AMG4642ER
is a rackmount four channel video receive unit designed to receive 4 video signals
and provide full duplex 100BaseT Ethernet conne
ctivity over two Multimode fibres.
The
AMG4642ER
is designed to plug into an AMG2005 or AMG2009 subrack, which in turn fits into a
19" rack system.
The
AMG4642ER
is designed to operate with
AMG4641E
or rackmount equivalent
AMG4641ER
four
channel video
transmit unit in a point to point configuration.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assume
d by AMG for its use.
Page
2
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.do
c
Contents
Introduction
3
Unit Functional Schematic
................................
................................
................................
..................
3
Optical Connection
................................
................................
................................
.............................
3
Connections
4
Video Output Connections
................................
................................
................................
..................
4
Optical Connections
................................
................................
................................
...........................
4
Power Connection
................................
................................
................................
..............................
4
Ethernet Connection
................................
................................
................................
...........................
4
Front Panel Indicators
5
Power LED
................................
................................
................................
................................
..........
5
Video Output LED’s
................................
................................
................................
............................
5
Fibre Optic LED’s
................................
................................
................................
...............................
5
Ethernet Data LED’s
................................
................................
................................
...........................
5
Ethernet Operation
6
Physical Information
7
Dimensions
................................
................................
................................
................................
.........
7
Mounting Details
................................
................................
................................
................................
.
7
Removal / replacement from / to the Case
................................
................................
.........................
7
Safety
7
Maintenance and Repair
7

AMG Systems Ltd. reserves the right to make changes to this
document without notic
e. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
3
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
Introduction
Unit Functional Schematic
The
AMG4642ER
drops off up to 4
video signals plus Ethernet data
transmitted from the
AMG4641E
.
It also transmits Ethernet data to the
AM
G4641E
.
Optical Connection
The
AMG4642ER
is connected as illustrated below when used with an
AMG4641ER
4
-
channel
transmit unit acting as a point to point system.

A
MG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
4
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
Connections
Video Output Connections
No. of channels
................................
....
4
Connectors
................................
..........
75 ohm BNC Socket
.
Output Impedance
...............................
75 ohm terminated.
Output Level
................................
........
1 Volt p
-
p nominal
Frequency Response
...........................
10Hz to 7MHz.
Optical Connections
PRIMARY OPTO OUT
Connector
................................
............
LC/PC
Primary Optical Launch Power
............
-
5dBm
Wavelength
................................
..........
1310nm
Optical Fibre
................................
........
Multimode 50/125 or 62.5/125**
PRIMARY OPTO IN
Connector
................................
............
LC/PC
Primary Optical Sensitivity
...................
-
22dBm
Wavelength
................................
..........
1310nm
Optical Fibre
................................
........
Multimode 50/125 or 62.5/125**
**Note: the transmission distance is limited by the bandwidth of the Multimode optical fibre. The optical
data rate is 1.25Gb
its/s. The maximum bandwidth specification at this data rate for Multimode fibre is
2km. although in most cases the units will operate successfully over longer fibre lengths. It is
advisable however for distances greater than 2km, to have the optical fibr
e tested.
Power Connection
Power supply
................................
.......
from plug in connection on the AMG2009 / AMG2015 subrack
Power consumption
.............................
10 Watts max.
Ethernet Connection
Ethernet Data Connector
....................
RJ45
Interface
................................
...............
Auto
-
negotiation up to 100BASE
-
TX full duplex
Ethernet Data Rat
e
..............................
Maximum 100Mb/s total Ethernet traffic on fibre

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for
its use.
Page
5
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
Front Panel Indicators
Power LED
Power
................................
..................
Green
-
unit powered
Off
-
no power applied to unit
Video Output LED’s
Video Present CH1
-
4
..........................
Green
-
video signal present on output BNC
Org
-
channel present but
no video on O/P BNC
Off
-
no video channel present
Fibre Optic LED’s
Primary Opto Sync TX
.........................
Green
-
optical channel transmitting
Off
-
optical channel not transmitting
Primary Opto Sync RX
........................
Green
-
optical channel receiving
Org
-
optical channel rece
iving but not sync.
Off
-
optical channel not transmitting
Ethernet Data LED’s
BANK A
Data Present TX (Ethernet)
.................
Green
-
data present on the Ethernet input
Off
-
no data present on the Ethernet input
This represents the Ethernet signals being
transmitted onto the optical fibre
Data Present RX (Ethernet)
................
Green
-
data present on the Ethernet input
Off
-
no data present on the Ethernet input
This represents the Ethernet signals being received from the optical fibre
BANK B
Data Present TX
................................
.
Green
-
RJ45 Ethernet port operating at 100Mbit/s
Red
-
RJ45 Ethernet port operating at 10Mbit/s
Data Present RX
................................
..
Green
-
RJ45 Ethernet port operating full duplex
Off
-
RJ45 Ethernet port operating half duplex
Note: the RJ45 Ethernet auto
-
nego
tiates up to 100Mbit/s full duplex.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The inform
ation herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
6
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
Ethernet Operation
In order for the AMG system to transmit Ethernet signals, an onboard RJ45 Ethernet interface or
X16003 Ethernet interface adaptor should be fitted to both the Transmit unit and the Receive unit.
T
he Ethernet interface can operate at either 10Mbits/s half duplex, or 100Mbit/s full duplex, and data is
transmitted from one port the other port with the minimum of delay or buffering.
The 100BaseT port does not implement MDI/MDIX; it should be connecte
d with a straight though
cable to an external switch port and with a cross over cable when connected directly to a PC or DTE.

AMG Systems Lt
d. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
7
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
Physical Information
Dimensions
Height
................................
..................
3U Plug
-
in
Width
................................
...................
14HP
Depth
................................
...................
170mm excluding connectors
Weight
................................
.................
1000grams
Mounting Detai
ls
The unit is designed to be mounted within an AMG2009 or AMG2015 Subrack on standard card
guides.
Removal / replacement from / to the Case
Note:
-
The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic
discharge
(ESD) procedures. Use properly grounded protection (for example, wrist straps) when
handling the PCB.
To remove units from the case to access the data expansion boards and the daughter boards, remove
the 2 or 4 fixing screws on the rear panel and slide t
he PCB's out of the case.
Ensure that the fibres do not snag or get trapped.
To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the
appropriate slots. Ensure that the fibre do not snag or get trapped.
Sa
fety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825
-
2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:

Do not stare with unprotected eyes or with any unapproved
collimating device at fibre
ends or connector faces, or point them at other people.

Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825
-
2:20
00 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact:
AMG Systems L
td.
at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone
[phone]
Technical Support
[phone]
Email
[e-mail]

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Pag
e
8
of
8
AMG4642ER
Instruction
Sheet
D16980
-
01.doc
This page is intentionally blank.