AMG AMG4744ER-SF User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is bel
ieved to
be accurate. No responsibility is assumed by AMG for its use.
Page
1
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
AMG4744ER
-
SF
Instruction Manual
4 Channel Video Receive Unit with Bi
-
directional Data
Channel and Ethernet for a Singlemode Fibre Link
The
AMG4744ER
-
SF
is a rackmount four channel video receive unit designed to receive 4 video
signals and tra
nsmit and receive 1 data signal plus full duplex 100BaseT Ethernet connectivity over
one Singlemode fibre.
The
AMG4744ER
-
SF
is designed to plug into an
AMG2005
or
AMG2009
subrack, which in turn fits
into a 19" rack system.
The
AMG4744ER
-
SF
is designed
to operate with
AMG4743E
-
SF
or rackmount equivalent
AMG4743ER
-
SF
four channel video transmit unit in a point to point configuration.

AMG Systems Ltd. reserves
the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
2
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Contents
Introduction
3
Unit Functional Schematic
................................
................................
................................
..................
3
Optical Connection
................................
................................
................................
.............................
3
Connections
4
Video Output Connections
................................
................................
................................
..................
4
Optical Connections
................................
................................
................................
...........................
4
Power Connection
................................
................................
................................
..............................
4
Ethernet Connection
................................
................................
................................
...........................
4
Data and Audio Channel Connections
................................
................................
...............................
4
Data and Audio Channel Configuration
5
Data and Audio Channel Configuration
................................
................................
..............................
5
Data Interface Connections Channel A
................................
................................
..............................
5
Data Channel A Configuration
................................
................................
................................
............
5
Front Panel Indicators
6
Power LED
................................
................................
................................
................................
..........
6
Video Output LED’s
................................
................................
................................
............................
6
Fibre Optic LED’s
................................
................................
................................
...............................
6
Low Speed Data LEDs
................................
................................
................................
.......................
6
Ethernet Operation
7
Physical Information
8
Dimensions
................................
................................
................................
................................
.........
8
Mounting Details
................................
................................
................................
................................
.
8
Removal / replacement from / to the Case
................................
................................
.........................
8
Safety
8
Maintenance and Repair
8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
3
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Introduction
U
nit Functional Schematic
The
AMG4744ER
-
SF
receives up to 4
video and 1 data signals from the
AMG4743E
-
SF
.
It also transmits 1 data signal to the
AMG4743E
-
SF
.
Ethernet connectivity is also provided
between the two units.
Optical Connection
The
AMG474
4ER
-
SF
is connected as illustrated below when used with an
AMG4743ER
-
SF
4
-
channel
transmit unit acting as a point to point system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is bel
ieved to
be accurate. No responsibility is assumed by AMG for its use.
Page
4
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Connections
Video Output Connections
No. of channels
................................
....
4
Connectors
................................
..........
75 ohm BNC Socket.
Output Impedance
...............................
75 ohm terminated
.
Output Level
................................
........
1 Volt p
-
p nominal
Frequency Response
...........................
10Hz to 7MHz.
Optical Connections
PRIMARY OPTO IN
Connector
................................
............
LC/PC
Optical Fibre
................................
........
One fibre
-
Singlemode
Primary Optical Launch Power
............
-
5dBm
Wavelength
................................
..........
1310nm
Primary Optical Sensitivity
...................
-
22dBm
Wavelen
gth
................................
..........
1310nm
Power Connection
Power supply
................................
.......
from plug in connection on the AMG2009 / AMG2015 subrack
Power consumption
.............................
10 Watts max.
Ethernet Connection
Ethernet Data Connector
....................
RJ45
Interface
................................
...............
Auto
-
negotiation up to 100BASE
-
TX full duplex
Ethernet Data Ra
te
..............................
Maximum 50Mbits/s total Ethernet traffic on fibre
Data and Audio Channel Connections
DATA CHANNEL A
Data Channel A
................................
...
1 channel
Data Connector
................................
....
RJ45
Channel A Interface
.............................
On Board Data Interface
–
RS232, RS422 or RS485. Selected
by slide switch above the RJ
45 connector.
RS232
–
switch position
-
high (closest to BNC connections)
RS422
–
switch position
–
middle
RS485
–
switch position
–
low (furthest from BNC connections)
DATA CHANNEL B
Data Channel B
................................
...
Not Present

AMG Systems Ltd. reserves the
right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
5
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Data and Audio Channel Configuration
Data and Audio Channel Configuration
The
AMG4744E
-
SF
and rackmount equivalent
AMG4744ER
-
SF
sends and receives data to/from
Channel A. Channel B is not available. Channel A is a single data interface selectable by the user with
the slide switch on the rear
panel.
Data Interface Connections Channel A
Channel A
RJ45 Pin
No.
RS485
[switch low]
RS422 [switch
mid]
RS232
[switch high]
Cat 5/6 Cable
Colour Code T568B
1
IN + (A)
GND
White/orange
2
IN
-
(B)
IN
Orange
3
White/green
4
Blue
5
White/blue
6
Green
7
IN/OUT + (A)
OUT + (A)
N/A
White/brown
8
IN/OUT
-
(B)
OUT
-
(B)
OUT
Brown
Note: (A) or (B) in brackets in above table refers to RS485 / RS422 data specification, not Channel A,
Channel B.
Data Cha
nnel A Configuration
Channel A is always present and allows for a RS232, RS422 (full duplex, four wire) or RS485 (half
duplex, two wire) interface depending on the position of the switch located above the RJ45 connector.
The switch signifies the presence o
f the X16004 Low Speed Data/Audio Interface Board. If there are
LED's present on the RJ45 connector then an X16003 Ethernet Interface Board is fitted.
The data input for both the RS485 and the RS422 modes detects a tri
-
state input condition by
monitoring
the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri
-
state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic zero respectively. It is impor
tant therefore to terminate the RS485 bus or
the RS422 input bus using 120Ωif a pre
-
bias is present on the RS485 or RS422 bus.
A large number of third party equipment manufacturers apply a pre
-
bias on their RS485 bus. This pre
-
bias is applied by pulling
one arm of the RS485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri
-
state condition, then these resistors should have a value above 5
kΩ. If the third party
bias resistors are less the 750Ωthe bus can be double or triple terminated as required to ensure that a
tri
-
state level is detected.
Note: The Data Channel A is shipped from the factory set up for RS485 operation unless otherwise
requested.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
6
of
8
AMG
4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Front Panel Indicators
Power LED
Power
................................
...................
Green
-
unit powered
Off
-
no power applied to unit
Video Output LED’s
Video Present CH1
-
4
...........................
Green
-
video signal present on output BNC
Org
-
channel present but no video on O/P BNC
Off
-
no video c
hannel present
Fibre Optic LED’s
Primary Opto Sync TX
.........................
Green
-
optical channel transmitting
Off
-
optical channel not transmitting
Primary Opto Sync RX
.........................
Green
-
optical channel receiving
Org
-
optical channel receiving but not sync.
Off
-
optical c
hannel not transmitting
Low Speed Data LEDs
Channel A
Data Present TX (RS485 or RS422)
...
Green
-
logic zero (+V,
-
V) present on IN+, IN
-
Red
-
logic one (
-
V,V+) present on IN+, IN
-
Off
-
tri
-
state off or no connection on IN+, IN
-
Data Present TX (RS232
)
....................
Green
-
logic zero (+V) present on input IN+
Red
-
logic transitions present on input IN+
Off
-
logic one (
-
V) present on input IN+
This represents the data signals being transmitted on the optical fibre
Data Present RX (RS485 or RS422)
...
Green
-
logi
c zero (+V,
-
V) present on OUT+, OUT
-
Red
-
logic one (
-
V,+V) present on OUT+, OUT
-
Off
-
tri
-
state off or no connection on OUT+, OUT
-
Data Present RX (RS232)
...................
Green
-
logic zero (+V) present on OUT+
Red
-
logic transitions present on OUT+
Off
-
logic
one (
-
V) present on OUT+
This represents the data signals being received on the optical fibre

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page
7
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Ethernet Operation
In order for the AMG system to transmit Ethernet signals, an onboard RJ45 Ethernet interface or
X16003 Ethernet interface adaptor should
be fitted to both the Transmit unit and the Receive unit.
The Ethernet interface can operate at either 10Mbits/s half duplex, or 100Mbit/s full duplex, and data is
transmitted from one port the other port with the minimum of delay or buffering. The maxim
um
bandwidth (at 100Mbit/s full duplex) available for transmission across the fibre link is nominally
50MBit/s.
The 100BaseT port does not implement MDI/MDIX; it should be connected with a straight though
cable to an external switch port and with a cross
over cable when connected directly to a PC or DTE.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG
for its use.
Page
8
of
8
AMG4744ER
-
SF
Instruction
Sheet
D18203
-
01.doc
Physical Information
Dimensions
Height
................................
...................
3U Plug
-
in
Width
................................
....................
14HP
Depth
................................
...................
170mm excluding connectors
Weight
................................
..................
1000grams
Mounting Details
The unit is designed to be mounted within an AMG2009 or AMG2015 Subrack
on standard card
guides.
Removal / replacement from / to the Case
Note:
-
The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist str
aps) when
handling the PCB.
To remove units from the case to access the data expansion boards and the daughter boards, remove
the 2 or 4 fixing screws on the rear panel and slide the PCB's out of the case.
Ensure that the fibres do not snag or get trapp
ed.
To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the
appropriate slots. Ensure that the fibre do not snag or get trapped.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance wi
th EN 60825
-
2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:

Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at oth
er people.

Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825
-
2:2000 or your local safety officer.
Maintenance and Repair
There are no us
er serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact:
AMG Systems Ltd.
at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG
18 8QB, UK.
Phone
[phone]
Technical Support
[phone]
Email
[e-mail]