AMI Marine Quark-Elec QK- A034 User manual

QK-A034 Manual
V 1.1
NMEA 0183
Features

Galvanically isolated NMEA and SeaTalk input ports
Multiplexes
up to three NMEA 0183 input devices
SeaTalk to NMEA converter

NMEA 0183 to NMEA 2000 converter (converts sentences to PGNs)

Configurable NMEA 0183 baud rates (4800, 9600, 38400bps)

Multiple outputs: WiFi, USB and NMEA 2000
WiFi: Ad-
hoc mode allows up to 4 devices to connect to the internal WiFi module simultan
WiFi:
Station mode allows for the connection of the A034 to your router/ access point for greater
number of wireless users and WiFi range.
WiFi: Standby option

WiFi and USB output of combined data in NMEA 0183 sentence format
WiFi and USB additional
ly output
format)

Compatible with Android and iOS via WiFi, excluding Configuration. (Configuration must be
completed using Windows software.)

Compatible with Windows, Mac, Linux
Filtering options for
overflow reduction and additional
1 of 15
QK-
A034
NMEA 0183
x 3 & SeaTalk1 to NMEA 2000 Converter
With Filtering and
WIFI/USB Outputs
Galvanically isolated NMEA and SeaTalk input ports
up to three NMEA 0183 input devices
with one SeaTalk input
NMEA 0183 to NMEA 2000 converter (converts sentences to PGNs)
Configurable NMEA 0183 baud rates (4800, 9600, 38400bps)
Multiple outputs: WiFi, USB and NMEA 2000
hoc mode allows up to 4 devices to connect to the internal WiFi module simultan
Station mode allows for the connection of the A034 to your router/ access point for greater
number of wireless users and WiFi range.
WiFi and USB output of combined data in NMEA 0183 sentence format
ly output
of
NMEA 2000 network PGNs (in both 0183 sentence and PCDIN
Compatible with Android and iOS via WiFi, excluding Configuration. (Configuration must be
completed using Windows software.)
Compatible with Windows, Mac, Linux
overflow reduction and additional
configuration.
2019
A034
Manual
x 3 & SeaTalk1 to NMEA 2000 Converter
WIFI/USB Outputs
hoc mode allows up to 4 devices to connect to the internal WiFi module simultan
eously
Station mode allows for the connection of the A034 to your router/ access point for greater
NMEA 2000 network PGNs (in both 0183 sentence and PCDIN
Compatible with Android and iOS via WiFi, excluding Configuration. (Configuration must be

QK-A034 Manual
V 1.1
Contents
1. Introduction
................................
2. Mounting
................................
3. Connections
................................
3.1. NMEA 0183 Inputs
................................
3.2. SeaTalk1 Input
................................
3.3. NMEA 2000 Output
3.3.1.
NMEA 0183 to NMEA 2000 conversions
3.4. WiFi Output
................................
3.4.1. WiFi Ad-
hoc mode connection
3.5. USB Output
................................
3.5.1.
Will a driverneededto connect via USB?
3.5.2.
Checking the USB connection (Windows)
4. Status LED’s
................................
5. Configuration
................................
5.1.
Configuring Baud Rates
5.2. WiFi - Station mode
5.3. WiFi - Standby
................................
5.4. Filtering
................................
5.4.1.
Configuring filters
5.5. USB -
Monitoring NMEA Messages
6. Upgrading firmware
................................
7. Specification
................................
8.
Limited Warranty and Notices
9. Disclaimer
................................
10. Document History
................................
2 of 15
................................
................................................................
................................
................................
................................................................
................................
................................
................................................................
................................
................................
................................
................................
................................
................................
................................
................................................................
................................
NMEA 0183 to NMEA 2000 conversions
................................
................................
................................
................................
................................
hoc mode connection
................................
................................
................................
................................
................................
Will a driverneededto connect via USB?
................................
................................
Checking the USB connection (Windows)
................................
................................
................................................................
................................
................................
................................................................
................................
Configuring Baud Rates
................................................................
................................
................................................................
................................
................................
................................
................................
................................
................................................................
..............................
Configuring filters
................................................................
................................
Monitoring NMEA Messages
................................
................................
................................
................................
................................
................................
................................................................
................................
Limited Warranty and Notices
................................................................
................................
................................
................................................................
................................
................................
................................
................................
2019
................................
...... 3
................................
.......... 4
................................
..... 5
................................
.............. 5
................................
.................... 6
................................
............. 7
................................
7
................................
.......................... 8
................................
................. 8
................................
.......................... 9
................................
. 9
................................
............................... 9
................................
.. 10
................................
.. 11
................................
.... 11
................................
........... 12
................................
................... 12
..............................
13
................................
... 13
................................
.................. 14
................................
........................ 14
................................
... 14
................................
........ 15
................................
...... 15
................................
.......................... 15

QK-A034 Manual
V 1.1
1. Introduction
The QK-A034 NMEA0183
multiplexer combines data from mul
data input. It outputs the combined messages to WiFi,
The A034 can
be used out of the box for standard functionality or configured for additional
sophistication.
Through advanced filtering
options
data input, blocking of unwanted
The A034
multiplexer has three NMEA 0183 inputs (listener
output port, a WiFi
and USB port to
INPUTS (listener ports)
3 x NMEA 0183
1 x SeaTalk
USB (Configuration only)
The internal SeaTalk converter allows the
to NMEA 0183 messages.
Standard Functionality:
The multiplexer converts and combines data received on the listener
portsand sends this data to NMEA 2000
Filtering options:
Each input also has a flexible filter that can be configured to pass or block
specificsentences. This frees up bandwidth, significantly reducing the possibility of data overflow and
resulting loss of data.
Data from multiple instruments is availa
freedom to monitor from anywhere on board. Up to 4 iPads, iPhone, Android phones
WiFi enabled devices can connect directly to the
USB port allows a computer-
based navigation application
can also be
used for configuration of specific WiFi and NMEA ports settings.
3 of 15
multiplexer combines data from mul
tiple NMEA 0183
inputs with
data input. It outputs the combined messages to WiFi,
USB and a NMEA 2000
output
be used out of the box for standard functionality or configured for additional
options
, the A034 NMEA 0183 multiplexer
enables controlled filtering of
data and overflow reduction.
multiplexer has three NMEA 0183 inputs (listener
-ports), one SeaTalk1
input,
and USB port to
output
to host devices such as PCs, laptops or tablets.
INPUTS (listener ports)
OUTPUTS (talker ports)
3 x NMEA 0183
1 x SeaTalk
1
1 x NMEA 2000
WiFi
USB (Configuration only)
USB
The internal SeaTalk converter allows the
A034 t
o listen on the SeaTalk bus and convert SeaTalk data
The multiplexer converts and combines data received on the listener
portsand sends this data to NMEA 2000
output port, WiFi interface and USB.
Each input also has a flexible filter that can be configured to pass or block
specificsentences. This frees up bandwidth, significantly reducing the possibility of data overflow and
Data from multiple instruments is availa
ble wirelessly though WiFi connections, giving complete
freedom to monitor from anywhere on board. Up to 4 iPads, iPhone, Android phones
WiFi enabled devices can connect directly to the
A034
with no need for an additional access point.The
based navigation application
to receive sentences from the multiplexer.It
used for configuration of specific WiFi and NMEA ports settings.
Figure 1: Function diagram
2019
inputs with
SeaTalk
output
port.
be used out of the box for standard functionality or configured for additional
enables controlled filtering of
input,
oneNMEA 2000
to host devices such as PCs, laptops or tablets.
o listen on the SeaTalk bus and convert SeaTalk data
The multiplexer converts and combines data received on the listener
Each input also has a flexible filter that can be configured to pass or block
specificsentences. This frees up bandwidth, significantly reducing the possibility of data overflow and
ble wirelessly though WiFi connections, giving complete
freedom to monitor from anywhere on board. Up to 4 iPads, iPhone, Android phones
, tablets or other
with no need for an additional access point.The
to receive sentences from the multiplexer.It

QK-A034 Manual
V 1.1
2. Mounting
The A034was designed for
the small
Despite the fact that the A034
case is water
a short circuit. The A034
should be mounted in a dry place such as b
flat surface.
A034
comes with an extruded aluminium enclosure with external dimensions of 114.5 x 110 x 32 mm
Ensure there is enough space around the multiplexer to connect the wirings.
4 of 15
the small
-
commercial, leisure, fishing boat and vessel monitoring markets.
case is water
resistant
, the terminals are open and seawater can cause
should be mounted in a dry place such as b
ehind the instrument panel on a
comes with an extruded aluminium enclosure with external dimensions of 114.5 x 110 x 32 mm
Ensure there is enough space around the multiplexer to connect the wirings.
Figure 2:Dimensions
2019
commercial, leisure, fishing boat and vessel monitoring markets.
, the terminals are open and seawater can cause
ehind the instrument panel on a
comes with an extruded aluminium enclosure with external dimensions of 114.5 x 110 x 32 mm
.

QK-A034 Manual
V 1.1
3. Connections
Figure
The A034
multiplexer has the following options for connection to inputs, outputs and host devices.
3x NMEA 0183 inputs
1x SeaTalk1 input
1x NMEA 2000output
WiFi Output
USB output
LED indicators
Power off all the devices before connecting!
3.1. NMEA 0183 Inputs
A034
has three NMEA inputs called IN1 to IN3. Each input should be connected to one output device
only. Th
ese inputs are galvanically isolated from the
standard.
Each input has an internal filter which can be configured to pass or block specific sentences from the
input devices (See the Configuration section).
A034
combines these filtered NMEA 0183 inputs with the NMEA sentences converted from the
SeaTalk input into one NMEA0183 serial data stream.
Every NMEA input on the A034
is galvanically isolated (also called opto
isolated input p
revents unwanted currents flowing between the instruments and the multiplexer. These
currents can damage equipment or interfere with radio signals and should therefore be avoided.
5 of 15
Figure
3: Typical system connection
multiplexer has the following options for connection to inputs, outputs and host devices.
Figure 4: Side view drawing
Power off all the devices before connecting!
has three NMEA inputs called IN1 to IN3. Each input should be connected to one output device
ese inputs are galvanically isolated from the
A034
multiplexer, as specified by the NMEA 0183
Each input has an internal filter which can be configured to pass or block specific sentences from the
input devices (See the Configuration section).
combines these filtered NMEA 0183 inputs with the NMEA sentences converted from the
SeaTalk input into one NMEA0183 serial data stream.
is galvanically isolated (also called opto
-
isolation).A galvanically
revents unwanted currents flowing between the instruments and the multiplexer. These
currents can damage equipment or interfere with radio signals and should therefore be avoided.
2019
multiplexer has the following options for connection to inputs, outputs and host devices.
has three NMEA inputs called IN1 to IN3. Each input should be connected to one output device
multiplexer, as specified by the NMEA 0183
Each input has an internal filter which can be configured to pass or block specific sentences from the
combines these filtered NMEA 0183 inputs with the NMEA sentences converted from the
isolation).A galvanically
revents unwanted currents flowing between the instruments and the multiplexer. These
currents can damage equipment or interfere with radio signals and should therefore be avoided.

QK-A034 Manual
V 1.1
NMEA baud rates are set to the following default settings:
NMEA IN 1: 4800 bps
NMEA IN 2: 4800 bps
NMEA IN 3: 38400bps
These can be adjusted as required, using the Configuration software (see the Configuration section).
Regarding connection to external NMEA devices:Although the NMEA 0183 standard specifies signal
names, voltage
levels and connection methods clearly; in reality, this standard has been interpreted
with variation between manufacturers. To ensure the
specifications of all devices before connecting them.
Connect the + and -
terminals of the NMEA input/output on the
output/input on the instrument (e.g., wind sensor, autopilot, chart plotter). These terminals
may also be labelled
A/B, Data+/Data
3.2. SeaTalk1 Input
The built-in SeaTalk1
to NMEA converter translates SeaTalk data into NMEA sentences. The SeaTalk
port has 3-
Pin terminals for connection to the SeaTalk bus. Ensure the connection is correct before
powering up. Inaccurate connection could damage the
The SeaTalk converter converts the
message is received, A034
checks if the message is supported. When the message is recognized as
being supported,
the message is ex
unsupported datagrams are ignored. These converted NMEA messages are filtered and then combined
with NMEA data received on the other inputs.
This function allows the NMEA multiplexer to listen on the
needed as
the SeaTalk bus is a single
to NMEA converter
works in one direction only. NMEA sentences are
Supported SeaTalk Datagra
SeaTalk
NMEA
00 DBT
10 MWV
11 MWV
20 VHW
21 VLW
22 VLW
23 MTW
25 VLW
26 VHW
27 MTW
50 ---
51 ---
52 ---
53 RMC
54 ---
56 ---
58 ---
89 HDG
99 ---
The table shows that not all datagrams result in an NMEA 0183 sentence. Some datagrams are only
used to retrieve data, which is combined with other datagrams to create one NMEA 0183
6 of 15
NMEA baud rates are set to the following default settings:
These can be adjusted as required, using the Configuration software (see the Configuration section).
Regarding connection to external NMEA devices:Although the NMEA 0183 standard specifies signal
levels and connection methods clearly; in reality, this standard has been interpreted
with variation between manufacturers. To ensure the
A034
is not damaged please double
specifications of all devices before connecting them.
terminals of the NMEA input/output on the
A034
to the + and
output/input on the instrument (e.g., wind sensor, autopilot, chart plotter). These terminals
A/B, Data+/Data
-, RX+/RX-, In+/In–.
to NMEA converter translates SeaTalk data into NMEA sentences. The SeaTalk
Pin terminals for connection to the SeaTalk bus. Ensure the connection is correct before
powering up. Inaccurate connection could damage the
A034 and other d
evices on the SeaTalk Bus.
The SeaTalk converter converts the
SeaTalk
messages in the conversion table below. When a SeaTalk
checks if the message is supported. When the message is recognized as
the message is ex
tracted, stored and converted to an NMEA sentence. Any
unsupported datagrams are ignored. These converted NMEA messages are filtered and then combined
with NMEA data received on the other inputs.
This function allows the NMEA multiplexer to listen on the
SeaTalk bus. Only one SeaTalk input is
the SeaTalk bus is a single
-cable system that connects all instruments
works in one direction only. NMEA sentences are
not converted to
Supported SeaTalk Datagra
ms
NMEA
Description
Depth below transducer
Wind angle, (10 and 11 combined)
Wind speed, (10 and 11 combined)
Speed through water, includes heading when
present
Trip mileage (21 and 22 combined)
Total mileage (21 and 22 combined)
Water temperature
Total and Trip mileage
Speed through water, includes heading when
present
Water temperature
GPS latitude, value stored
GPS longitude, value stored
GPS speed over ground, value stored
Course over ground. RMC sentence is
generated from stored values from other GPS
Related datagrams.
GPS time, value stored
GPS date, value stored
GPS lat/long, values stored
Magnetic heading, including variation (99)
Magnetic variation, value stored
The table shows that not all datagrams result in an NMEA 0183 sentence. Some datagrams are only
used to retrieve data, which is combined with other datagrams to create one NMEA 0183
2019
These can be adjusted as required, using the Configuration software (see the Configuration section).
Regarding connection to external NMEA devices:Although the NMEA 0183 standard specifies signal
levels and connection methods clearly; in reality, this standard has been interpreted
is not damaged please double
-check the
to the + and
- terminals of the
output/input on the instrument (e.g., wind sensor, autopilot, chart plotter). These terminals
to NMEA converter translates SeaTalk data into NMEA sentences. The SeaTalk
Pin terminals for connection to the SeaTalk bus. Ensure the connection is correct before
evices on the SeaTalk Bus.
messages in the conversion table below. When a SeaTalk
checks if the message is supported. When the message is recognized as
tracted, stored and converted to an NMEA sentence. Any
unsupported datagrams are ignored. These converted NMEA messages are filtered and then combined
SeaTalk bus. Only one SeaTalk input is
. The A034 SeaTalk
not converted to
SeaTalk.
Speed through water, includes heading when
Speed through water, includes heading when
generated from stored values from other GPS
The table shows that not all datagrams result in an NMEA 0183 sentence. Some datagrams are only
used to retrieve data, which is combined with other datagrams to create one NMEA 0183
sentence.

QK-A034 Manual
V 1.1
3.3. NMEA 2000 Output
The A034 converter provides a 1
-
the three NMEA 0183 inputs and the SeaTalk input and then converter them to be NMEA 2000 PGNs.
With A034, NMEA 0183 and SeaTalk1 dat
capable instruments, such as NMEA 200 chart
The A034 requires power from a NMEA 2000
and terminated on both ends.
An
with two terminators
(termination resistors)
must be connected. It is not possible to simply connect two NMEA 2000devices directly together.
NMEA 2000 de
vice connects to the backbone with a T
A034 is supplied with a spurred
five
male micro-
fit connector. Simply connect the cable to the network backbone using a T
3.3.1.
NMEA 0183 to NMEA 2000 conversions
The following NMEA 0183 to NMEA 2000 conversions are currently supported.
NMEA 0183
sentence
Function
DBT
Depth Below Transducer
DPT Depth
GGA
Global Positioning System Fi
GLL
Geographic Position Latitude/Longitude
GSA
GNSS DOP and Active Satellites
GSV
GNSS Satellites in View
HDG
Heading, Deviation & Variation
HDM
Heading, Magnetic
HDT
Heading, T
MTW
Water Temperature
MWD
Wind Direction & Speed
MWV
Wind Speed and Angle (True or relative)
RMB
Recommended Minimum Navigation Information
RMC*
Recommended Minimum Specific GNSS Data
ROT
Rate Of Turn
RPM
Revolutions
RSA
Rudder Sensor Angle
VHW
Water Speed and Heading
VLW
Dual Ground/Water Distance
VTG*
Course Over Ground and Ground Speed
VWR
Relative (Apparent) Wind Spee
XTE
Cross Track Error, Measured
ZDA
Time & Date
VDM
AIS Message 1,2,3
VDM
AIS Message 4
VDM
AIS Message 5
VDM
AIS Message 9
VDM
AIS Message 14
VDM
AIS Message 18
VDM
AIS Me
VDM
AIS Message 21
VDM
AIS Message 24
*please note: some PGN sentences that are received require ad
7 of 15
-
way connection to an NMEA 2000 chart plotter.
The A034 combines
the three NMEA 0183 inputs and the SeaTalk input and then converter them to be NMEA 2000 PGNs.
With A034, NMEA 0183 and SeaTalk1 dat
a from legacy devices can be available on new NMEA 2000
capable instruments, such as NMEA 200 chart
plotters.
The A034 requires power from a NMEA 2000
backbone. An
NMEA 2000 backbone must be power
An
NMEA 2000 network must at least consist of,
a powered backbone
(termination resistors)
, to which the multiplexer and
any other NMEA 2000 devices
must be connected. It is not possible to simply connect two NMEA 2000devices directly together.
vice connects to the backbone with a T
- piece connector.
five
-
core screened cable for the NMEA 2000 connection, fitted with a
fit connector. Simply connect the cable to the network backbone using a T
NMEA 0183 to NMEA 2000 conversions
The following NMEA 0183 to NMEA 2000 conversions are currently supported.
Function
Converted to
2000 PGN
Depth Below Transducer
128267
128267
Global Positioning System Fi
x Data
126992, 129025, 129029
Geographic Position Latitude/Longitude
126992, 129025
GNSS DOP and Active Satellites
129539
GNSS Satellites in View
129540
Heading, Deviation & Variation
127250
Heading, Magnetic
127250
Heading, T
rue 127250
Water Temperature
130311
Wind Direction & Speed
130306
Wind Speed and Angle (True or relative)
130306
Recommended Minimum Navigation Information
129283,129284
Recommended Minimum Specific GNSS Data
126992, 127258, 12902
12902
Rate Of Turn
127251
Revolutions
127488
Rudder Sensor Angle
127245
Water Speed and Heading
127250, 128259
Dual Ground/Water Distance
128275
Course Over Ground and Ground Speed
129026
Relative (Apparent) Wind Spee
d and Angle 130306
Cross Track Error, Measured
129283
Time & Date
126992
AIS Message 1,2,3
129038
AIS Message 4
129793
AIS Message 5
129794
AIS Message 9
129798
AIS Message 14
129802
AIS Message 18
129039
AIS Me
ssage 19 129040
AIS Message 21
129041
AIS Message 24
129809. 129810
*please note: some PGN sentences that are received require ad
ditional data before being sent.
2019
The A034 combines
the three NMEA 0183 inputs and the SeaTalk input and then converter them to be NMEA 2000 PGNs.
a from legacy devices can be available on new NMEA 2000
NMEA 2000 backbone must be power
ed
a powered backbone
any other NMEA 2000 devices
must be connected. It is not possible to simply connect two NMEA 2000devices directly together.
Each
core screened cable for the NMEA 2000 connection, fitted with a
fit connector. Simply connect the cable to the network backbone using a T
-piece connector.
Converted to
NMEA
2000 PGN
126992, 129025, 129029
126992, 129025
129283,129284
126992, 127258, 12902
5,
127250, 128259
129809. 129810
ditional data before being sent.

QK-A034 Manual
V 1.1
3.4. WiFi Output
The A034
allows users to view their data through WiFi on a PC, tablet,
enabled device. Users can access marine network data including vessel course, speed, position, wind
speed, direction, water depth, AIS etc. These can be viewedin the chart softwar
The IEEE 802.11b/g wireless standard has two basi
and station mode (also called infrastructure mode).
The A034 supports 3 modes.
In Ad-hoc mode,
wireless devices connect directly (peer to peer)
For example, your smartph
one can connect directly to the A034 to receiver marine data.
In Station mode,
wireless devices communicate through an access point (AP) such as a router that
serves as a bridge to other networks (such as the Internet or LAN). This allows your router to ha
the data and traffic from your device. This data can then be picked up through your router anywhere
on your local area network. Increasing the WiFi range. Similar to plugging the device directly into the
router, but using
wireless technology. In this
and other AP
connections such as Internet.
WiFi can also be disabled in
Standby mode
when connecting 2 WiFi
transmitting devices.
The A034 is set to Ad-
hoc mode as a default setting, but can be easily setup to station mode or
standby mode through the configuration tool.
3.4.1. WiFi Ad-hoc mode
connection
From a Phone, Tablet or PC:
Once the A034 has powered up
,
Connect to ‘QK-A034xxxx
’ with the default
password: ‘88888888’.
In the chart software (or
chart plotter
Set the protocol to ‘TCP
’, IP address to
‘192.168.1.100’
and the port number to
With the above settings, a wireless connection
the chart software.
Note: In Ad-hoc mode,
the IP address should not be changed.
The SSID and password can be changed
The wireless connection
and data flow
checked with TCP/IP port monitoring software
as shown.
(Image: TCP/IP Net Assistant
shown as
example)
For Station m
ode WiFi or to disable
8 of 15
allows users to view their data through WiFi on a PC, tablet,
smartphone or other WiFi
enabled device. Users can access marine network data including vessel course, speed, position, wind
speed, direction, water depth, AIS etc. These can be viewedin the chart softwar
e.
The IEEE 802.11b/g wireless standard has two basi
c modes of operation; Ad-
hoc mode (peer to peer)
and station mode (also called infrastructure mode).
wireless devices connect directly (peer to peer)
without a router or access point.
one can connect directly to the A034 to receiver marine data.
wireless devices communicate through an access point (AP) such as a router that
serves as a bridge to other networks (such as the Internet or LAN). This allows your router to ha
the data and traffic from your device. This data can then be picked up through your router anywhere
on your local area network. Increasing the WiFi range. Similar to plugging the device directly into the
wireless technology. In this
way, the mobile devices receive both your marine
connections such as Internet.
Standby mode
. This reduces
power consumption
transmitting devices.
hoc mode as a default setting, but can be easily setup to station mode or
standby mode through the configuration tool.
(See Configuration section)
connection
,
scan for a WiFi network with an SSID of ‘QK-
A034xxxx’ or similar
’ with the default
chart plotter
),
’, IP address to
and the port number to
‘2000’.
With the above settings, a wireless connection
is
established and the user will receive the data through
the IP address should not be changed.
The SSID and password can be changed
. The password must be 8 to
12 characters long
and data flow
can be
checked with TCP/IP port monitoring software
shown as
ode WiFi or to disable
the WiFi function, see the
Configuration
A034 SSID
Similar to ‘QK
WiFi password
88888888
Protocol TCP
IP address
192.168.1.100
Data Port 2000
2019
smartphone or other WiFi
enabled device. Users can access marine network data including vessel course, speed, position, wind
hoc mode (peer to peer)
without a router or access point.
one can connect directly to the A034 to receiver marine data.
wireless devices communicate through an access point (AP) such as a router that
serves as a bridge to other networks (such as the Internet or LAN). This allows your router to ha
ndle
the data and traffic from your device. This data can then be picked up through your router anywhere
on your local area network. Increasing the WiFi range. Similar to plugging the device directly into the
way, the mobile devices receive both your marine
data
power consumption
and may be required
hoc mode as a default setting, but can be easily setup to station mode or
A034xxxx’ or similar
.
established and the user will receive the data through
12 characters long
.
Configuration
section.
Similar to ‘QK
-A034xxxx’
88888888
192.168.1.100

QK-A034 Manual
V 1.1
3.5. USB Output
The A034
is supplied with a type B USB connector. The connector can be linked directly to a USB port
on the PC.
The USB connector provid
es data output as standard (multiplexed information from all input
instruments will be sent to this connection). The host port is also used to configure the multiplexer and
to update its firmware.
3.5.1. Will a driver be
neededto connect via USB?
To enable the US
B data connection of A034 to other devices, related hardware drivers may be needed
dependent on your system requirements.
Mac:
No driver required.For Mac OS X, the A034 will be recognized and shown as a USB modem. The ID
can be checked with the following
1.
Plug the A03 into a USB port and launch Terminal.app.
2. Type: less /dev/*sub*
3.
The Mac system will return a list of USB devices. A034 will display as
where XYZ is a number. Nothing further needs to be done if it is listed.
Linux:
No driver required. When plugged into the computer, A034 will show up as a USB CDC device on
/dev/ttyACM0.
Windows 7,8,10:
The drivers usually install
automatically if your device is running an original Windows 10 version.
COM port will automat
ically show up in the device manager
The A034 registers itself to the computer as a virtual serial com port.
atically, it
3.5.2.
Checking the USB connection (Windows)
After the driver is installed
(if needed)
and check the COM number
(this is the number associated
with the USB port you are using.
number that Windows assigns as an input device. These can
be generated randomly by your computer
may require your COM number in order to access the data.
The port number for the A034 can be found in Windows
‘Control Panel->System-
>Device Manager’ under ‘Ports (COM
& LPT)’. Find the A034
in the list for the USB variant. To
change this number, double click the A034 and select the ‘Port
Settings’ tab. Click the ‘Advanced’ button and change the port
number to the one required.
Checking the USB data flow:
If desired, the USB data can always be checked with the
configuration tool. To do this, run the configuration tool,
connect to A034 and then click ‘Open Port’, the input data
will be shown on the display field.
(See Configuration section)
9 of 15
is supplied with a type B USB connector. The connector can be linked directly to a USB port
es data output as standard (multiplexed information from all input
instruments will be sent to this connection). The host port is also used to configure the multiplexer and
neededto connect via USB?
B data connection of A034 to other devices, related hardware drivers may be needed
dependent on your system requirements.
No driver required.For Mac OS X, the A034 will be recognized and shown as a USB modem. The ID
can be checked with the following
steps:
Plug the A03 into a USB port and launch Terminal.app.
The Mac system will return a list of USB devices. A034 will display as
-
“/dev/tty.usbmodemXYZ”
where XYZ is a number. Nothing further needs to be done if it is listed.
No driver required. When plugged into the computer, A034 will show up as a USB CDC device on
automatically if your device is running an original Windows 10 version.
ically show up in the device manager
once powered and connected via USB.
The A034 registers itself to the computer as a virtual serial com port.
If the driver does not install auto
If the driver does not install autommatically,
can be found on the included CD and
Checking the USB connection (Windows)
(if needed)
, run the Device Manager
(this is the number associated
with the USB port you are using.
The port number is the
number that Windows assigns as an input device. These can
be generated randomly by your computer
). Your chart software
may require your COM number in order to access the data.
The port number for the A034 can be found in Windows
>Device Manager’ under ‘Ports (COM
in the list for the USB variant. To
change this number, double click the A034 and select the ‘Port
Settings’ tab. Click the ‘Advanced’ button and change the port
If desired, the USB data can always be checked with the
configuration tool. To do this, run the configuration tool,
connect to A034 and then click ‘Open Port’, the input data
will be shown on the display field.
2019
is supplied with a type B USB connector. The connector can be linked directly to a USB port
es data output as standard (multiplexed information from all input
instruments will be sent to this connection). The host port is also used to configure the multiplexer and
B data connection of A034 to other devices, related hardware drivers may be needed
No driver required.For Mac OS X, the A034 will be recognized and shown as a USB modem. The ID
“/dev/tty.usbmodemXYZ”
No driver required. When plugged into the computer, A034 will show up as a USB CDC device on
automatically if your device is running an original Windows 10 version.
A new
once powered and connected via USB.
downloaded.

QK-A034 Manual
V 1.1
4. Status LED’s
A034 features eight LEDs which indicate SeaTalk in,
WIFIand Power status respectively.
The status LEDs on the panel show port activity and system status.
SeaTalk and NMEA IN1/2/3:
LEDs will flash for each valid message received.
NMEA 2000OUT
: LED will flash for each valid NMEA 2000 PGN sent out on NMEA 2000 port.
USB, WiFi：
LED will flash for each valid NMEA message sent to US
PWR (Power)
: LED light is constantly lit in red when the device is powered.
SeaTalk IN
NMEA IN 1
10 of 15
A034 features eight LEDs which indicate SeaTalk in,
NMEA IN, IN2, IN3,
NMEA2000
WIFIand Power status respectively.
The status LEDs on the panel show port activity and system status.
Figure 5:LED indications
LEDs will flash for each valid message received.
: LED will flash for each valid NMEA 2000 PGN sent out on NMEA 2000 port.
LED will flash for each valid NMEA message sent to US
B/WiFi outputs.
: LED light is constantly lit in red when the device is powered.
NMEA IN 1
NMEA IN 2 NMEA IN 3 N2K OUT USB WiFi Power
2019
NMEA2000
OUTPUT, USB,
: LED will flash for each valid NMEA 2000 PGN sent out on NMEA 2000 port.
B/WiFi outputs.

QK-A034 Manual
V 1.1
are can be found on the free CD provided with your product or at
loads/configuration
tool can be used to setup the port routing, sentence filtering, NMEA
he
ration tool must be used on a windows PC (or a Mac using
lating software) while the
The configuration tool must not be opened while another program is using the
down all applications using the
A034
Once open, click ‘Connect’.
Figure
5.1.
Configuring Baud Rates
NMEA 0183 input baud rates can be setup from dropdown menu.
NMEA 0183 devices (4800bps) or the high
be chosen.
NMEA baud rates are set to
the following default settings:
Seatalk:4800bps
NMEA IN 1: 4800bps
NMEA IN 2: 4800bps
NMEA IN 3: 38400bps
These can be adjusted as required.
11 of 15
sof our product or at
elec.com/do
Windows configuratio ce filtering, NMEA
baud rates, and WiFi settings fo
NMEA sentences
through the USB port. The confi Mac using
BootCamp or other Windows si
USB cable. The
A03
The configuration tool must not be opened while another program is using the
A034
A034
when using the configuration tool.
Figure
6:Configuration tool connection
Configuring Baud Rates
NMEA 0183 input baud rates can be setup from dropdown menu.
A034
can work with the standard
NMEA 0183 devices (4800bps) or the high
-
speed NMEA 0183 devices (38400bps), 9600bps can also
the following default settings:
These can be adjusted as required.
Figure 7:Setup the baud rate
2019
software can be found on the free CD provided with
Windows configuration tool can be used to setup the port routing, sent
nitor and se
through the USB port. The configuration tool must be used on a windows PC (or
is connected vi
5. Configuration
The A034 Configuration tool software can be found on the free CD provided with your product.
The A034 Windows configuration tool can be used to setup the port routing, sentence filtering,
NMEA baud rates, and WiFi settings forr t the A034. It can also be used to monitor and send NMEA
sentences through the USB port. The configuration tool must be used on a windows PC (or a Mac
using BootCamp or other Windows simulating software) while the A034 is connected via USB cable.
The software cannot access the A0344 via WiFi.
A034
. Please close
can work with the standard
speed NMEA 0183 devices (38400bps), 9600bps can also

QK-A034 Manual
V 1.1
When A034
is connected to a computer (Windows system) and
shown at the centre
of the bottom and the software version shows at the bottom right. Press ‘
once you have set the Baud rates for the inputs to save them to the
Then press the ‘Disconnect’
button to safel
Re-start the A034 to activate
the new settings to the device.
5.2. WiFi - Station mode
WiFi is set to ad-
hoc mode as standard. Station mode
handle the data from your device. This data
your local area network (
Similar to plugging the device directly into the router, but using wireless
technology). This
allows your mobile device to still receive Internet
To begin setup station mode the
(Mac users can use BootCamp).
1. Connect A034
to computer via Micro USB B
connection.
2.
Run the Configuration software (having closed any
other programs that wou
ld access the
check connection to the
A034
Configuration tool.
3. Change working mode to ‘
Station mode’
4. Enter your router’s SSID.
5. Enter the password
for your network.
6. Enter the IP address
assigned
normally start wit
h 192.168. The third group of digits
depends on your router’s configuration(commonly 1
or 0). The fourth group must be a unique number
between 0 and 255) This number must not be used
by any other equipment connected to your router.
7. Enter your router’s IP a
ddress
router. Leave the other settings as they are.
8. Click ‘Config’
in the bottom right hand corner and wait 60 seconds. After 60 seconds Click
‘Disconnect’.
9. Repower the A034
and it will now attem
In your chart software,
set the protocol as ‘
enter the Port number as ‘2000’.
You should now see your marine dat
and confirm the IP address
that your router has assigned the
different IP address
to a device than the one you chose to assign it during Configuration. If this is the
case,
copy the IP address from the r
If the IP address in the router’s
IP address list
everything will work in station mode.
If you are not able to view your data in station mode, the likely cause is either the
incorrectly, or the IP address is different in your chart software to that of your router.
5.3. WiFi - Standby
The WiFi module
can be disabled by selecting ‘standby’ in the WiFi menu
12 of 15
is connected to a computer (Windows system) and
powered up, ‘
A034
of the bottom and the software version shows at the bottom right. Press ‘
once you have set the Baud rates for the inputs to save them to the
A034.
button to safel
y remove the device from the PC.
the new settings to the device.
hoc mode as standard. Station mode
however,
allows your router/access point to
handle the data from your device. This data
can then be picked up through your router anywh
Similar to plugging the device directly into the router, but using wireless
allows your mobile device to still receive Internet
while view
ing your marine data
To begin setup station mode the
A034 should be connected via USB
to a computer running Wind
to computer via Micro USB B
Run the Configuration software (having closed any
ld access the
A034) and
A034
at the bottom of
Station mode’
for your network.
assigned
to the A034. This
h 192.168. The third group of digits
depends on your router’s configuration(commonly 1
or 0). The fourth group must be a unique number
between 0 and 255) This number must not be used
by any other equipment connected to your router.
ddress
in the Gateway
section. This can usually be found under the
router. Leave the other settings as they are.
in the bottom right hand corner and wait 60 seconds. After 60 seconds Click
and it will now attem
pt to connect to the router.
set the protocol as ‘
TCP’, insert the IP address
you assigned the
You should now see your marine dat
a in your chart software. If not,
check your router’s
that your router has assigned the
A034
. Occasionally, a router
to a device than the one you chose to assign it during Configuration. If this is the
copy the IP address from the r
outer into your chart software.
IP address list
matched the one inputted into
the chart software,
everything will work in station mode.
If you are not able to view your data in station mode, the likely cause is either the
incorrectly, or the IP address is different in your chart software to that of your router.
can be disabled by selecting ‘standby’ in the WiFi menu
2019
A034
connected’ will be
of the bottom and the software version shows at the bottom right. Press ‘
Config’
allows your router/access point to
can then be picked up through your router anywh
ere on
Similar to plugging the device directly into the router, but using wireless
ing your marine data
.
to a computer running Wind
ows
section. This can usually be found under the
in the bottom right hand corner and wait 60 seconds. After 60 seconds Click
you assigned the
A034and
check your router’s
IP address list
. Occasionally, a router
assigns a
to a device than the one you chose to assign it during Configuration. If this is the
the chart software,
data has been input
incorrectly, or the IP address is different in your chart software to that of your router.

QK-A034 Manual
V 1.1
5.4. Filtering
The A034 features filtering of NMEA 0183 sente
configured to pass or block specific sentences from entering the multiplexer.
NMEA sentences can be passed or blocked, specified by input
reducing the possibility o
f data overflow and resulting loss of data.
Black listed input data isfiltered
out and ignored by the A034 multiplexer, remaining desired data is then
transmitted to the outputs. As
default,
filters.
Filters can be set through the Configuration software.
Filtering allows the A034
the reduce the processing data load, by disabling these unneeded input
sentences. GPS receivers for example often
fill much of the available bandwidth of an NMEA 0183 port at 4800bps. By filtering out any unnecessary
data, bandwidth is saved for other devices’ data.
Most of Chart plotters also have their own sen
applications do not. So, using the black list to filter un
Filtering also removespotential
conflict
Users may choose
to enable this data on one input only (filtering), and to transmit to the outputs.
5.4.1. Configuring filters
Each input port’s black list can block up to 8 types
filter out an unwanted message type
details in the corresponding ‘B
lack
Simply, r
emove the ‘$’ or ‘!’ from the
sentence identifier and insert separated by
block ‘!AIVDM’ and ‘$GPAAM’ enter ‘AIVDM,GPAAM’. If blackli
SeaTalk data, use the co
rresponding NMEA message header.
SeaTalk section for a full list of converted messages).
13 of 15
The A034 features filtering of NMEA 0183 sente
nces.
Each input has a flexible filter that can be
configured to pass or block specific sentences from entering the multiplexer.
NMEA sentences can be passed or blocked, specified by input
.
This frees up bandwidth, significantly
f data overflow and resulting loss of data.
out and ignored by the A034 multiplexer, remaining desired data is then
default,
all filter lists are empty so all messages are passed through t
Filters can be set through the Configuration software.
Figure 8:Filtering
the reduce the processing data load, by disabling these unneeded input
sentences. GPS receivers for example often
transmit an abundance of sentences every second and can
fill much of the available bandwidth of an NMEA 0183 port at 4800bps. By filtering out any unnecessary
data, bandwidth is saved for other devices’ data.
Most of Chart plotters also have their own sen
tence filter, however many PC/mobile phone
applications do not. So, using the black list to filter un
-
necessary sentences is very helpful.
conflict
if
two similar NMEA devices provide the same
to enable this data on one input only (filtering), and to transmit to the outputs.
Each input port’s black list can block up to 8 types
sentences. To
filter out an unwanted message type
s from a specific input, enter the
lack
List’ in the Configuration software.
emove the ‘$’ or ‘!’ from the
5-digit NMEA talker and
sentence identifier and insert separated by
commas. For example to
block ‘!AIVDM’ and ‘$GPAAM’ enter ‘AIVDM,GPAAM’. If blackli
sting
rresponding NMEA message header.
(see
SeaTalk section for a full list of converted messages).
2019
Each input has a flexible filter that can be
This frees up bandwidth, significantly
out and ignored by the A034 multiplexer, remaining desired data is then
all filter lists are empty so all messages are passed through t
he
the reduce the processing data load, by disabling these unneeded input
transmit an abundance of sentences every second and can
fill much of the available bandwidth of an NMEA 0183 port at 4800bps. By filtering out any unnecessary
tence filter, however many PC/mobile phone
-based
necessary sentences is very helpful.
two similar NMEA devices provide the same
sentence type.
to enable this data on one input only (filtering), and to transmit to the outputs.

QK-A034 Manual
V 1.1
5.5. USB - Monitoring
NMEA Messages
Connect A034 and then click ‘Open port’, all the output sentences will be displayed in the appli
6. Upgrading firmware
The current firmware version can be
firmware version will showi
n the bottom of the Configuration software window).
To upgrade the firmware,
1.
Power up A034 and then connect it to Windows computer via USB.
2.
Run the Configuration software
3. Ensure the configuration tool
is connected to the
4.
A new Window will pop up with a drive named ‘STM32’ or s
and wait around 10 seconds to make sure the full file has been copied.
5.
Close the window and the Configuration software.
6. Re-power the A034
, then the new firmware will be
7. Specification
Item
DC supply
Average supply current (typical quiescent)
NMEA data format
NMEA input data rate
WiFi mode
Security
Operating temperature
Storage temperature
14 of 15
NMEA Messages
Connect A034 and then click ‘Open port’, all the output sentences will be displayed in the appli
Figure 9: Monitor via USB
The current firmware version can be
verified through the con
figuration tool (When connected, the
n the bottom of the Configuration software window).
Power up A034 and then connect it to Windows computer via USB.
Run the Configuration software
.
is connected to the
A034, and then click Ctrl+F7.
A new Window will pop up with a drive named ‘STM32’ or s
imilar. Copy the firmware into this drive
and wait around 10 seconds to make sure the full file has been copied.
Close the window and the Configuration software.
, then the new firmware will be
active.
Specification
NMEA 2000 network power
Average supply current (typical quiescent)
360mA
ITU/ NMEA 0183 format
4.8k to 38.4kbps, RS-
422 galvanically isolated
Ad-
hoc/Station mode on 802.11 b/g/n.
WPA/WPA2
-25°C to +80°C
-25°C to +85°C
2019
Connect A034 and then click ‘Open port’, all the output sentences will be displayed in the appli
cation.
figuration tool (When connected, the
imilar. Copy the firmware into this drive
422 galvanically isolated
hoc/Station mode on 802.11 b/g/n.

QK-A034 Manual
V 1.1
8.
Limited Warranty and
Quark-
elec warrants this product to be free from defects in materials and manufacture for one year from
the date of purchase. Quark-
elec will,
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour.
The customer is, however, responsible for any transportation costs incurred in returni
Quark-
Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized
alteration or repairs. A returns number must be given before any unit is sent back for repair.
The above does not affect the statutory rights o
9. Disclaimer
This product is designed to aid navigation and should be used to augment normal navigational
procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark
nor their distributors or
dealers accept responsibility or liability either to the products user or their estate
for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use this product.
Quark-
products may be upgraded from time to time and fu
exactly with this manual. The manufacturer of this product disclaims any liability for consequences
arising from omissions or inaccuracies in this manual and any other documentation provided with this
product.
10. Document History
Issue Date
Changes / Comments
1.0 02-01-2020
Initial release
1.1 15-01-2020
Minor edits
15 of 15
)
drant
G8 5HL
c.com
Limited Warranty and
Notices
elec warrants this product to be free from defects in materials and manufacture for one year from
elec will,
at its sole option, repair or replace any components that fail in
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour.
The customer is, however, responsible for any transportation costs incurred in returni
Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized
alteration or repairs. A returns number must be given before any unit is sent back for repair.
The above does not affect the statutory rights o
f the consumer.
This product is designed to aid navigation and should be used to augment normal navigational
procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark
dealers accept responsibility or liability either to the products user or their estate
for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use this product.
products may be upgraded from time to time and fu
ture versions may therefore not correspond
exactly with this manual. The manufacturer of this product disclaims any liability for consequences
arising from omissions or inaccuracies in this manual and any other documentation provided with this
Changes / Comments
Initial release
Minor edits
2019
elec(
Unit 7, the Q
e
[email protected]
[phone]
amimarine.com
elec warrants this product to be free from defects in materials and manufacture for one year from
at its sole option, repair or replace any components that fail in
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour.
The customer is, however, responsible for any transportation costs incurred in returni
ng the unit to
Elec. This warranty does not cover failures due to abuse, misuse, accident or unauthorized
alteration or repairs. A returns number must be given before any unit is sent back for repair.
This product is designed to aid navigation and should be used to augment normal navigational
procedures and practices. It is the user’s responsibility to use this product prudently. Neither Quark
-elec,
dealers accept responsibility or liability either to the products user or their estate
for any accident, loss, injury or damage whatsoever arising out of the use or of liability to use this product.
ture versions may therefore not correspond
exactly with this manual. The manufacturer of this product disclaims any liability for consequences
arising from omissions or inaccuracies in this manual and any other documentation provided with this