AMI VAPOR-C User manual

AMI Global
6280 S. Valley View #212, Las Vegas NV, 89118
Phone [phone] Fax [phone]
Website www.amiglobal.com
DISCOVER YOUR DIGITAL POTENTIAL
VAPOR-C
MANUAL & SPECIFICATIONS
VERSION: 2.4

DISCOVER YOUR DIGITAL POTENTIAL
2
TABLE OF CONTENTS
SAFETY STATEMENTS ........................................................................................................................................3
FCC LABEL......................................................................................................................................................4
SPECIFICATIONS...............................................................................................................................................5
ASSEMBLY......................................................................................................................................................6
DIMENSIONS ..................................................................................................................................................6
MOUNTING ....................................................................................................................................................7
WIRING .........................................................................................................................................................9
BATTERIES REPLACEMENT................................................................................................................................11
Date
Document Version
Comments
By
11/18/18
2.0
Created
Ori Peled
11/26/18
2.2
Adding FCC label artwork
Ori Peled
01/15/19
3.4
Update text
Ori Peled

DISCOVER YOUR DIGITAL POTENTIAL
3
SAFETY STATEMENTS
WARNING: Changes or modifications which are not expressly approved by AMI Global LLC could void the user’s
authority to operate the equipment.
The distance between user and products should be no less than 20cm
AVERTISSEMENT: Les changements ou modifications qui ne sont pas approuvés par COMPANY XXX pourrait
annuler l'autorité de l'utilisateur de faire fonctionner l'équipement
La distance entre l'utilisateur et de produits ne devrait pas être inférieure à 20cm
ATTENTION: This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation. The distance between user and products
should be no less than 20cm.
ISED RSS-GEN statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS(s) d'Innovation,
Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
ISED RSS-102
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by
Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna
to a general bystander of xx inches (xx cm) to maintain compliance with the General Population limits.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux
limites établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale
de xx pouces (xx cm) séparant l’antenne d’une personne présente en conformité avec les limites permises
d’exposition du grand public

DISCOVER YOUR DIGITAL POTENTIAL
4
FCC LABEL (VERIZON CAT-1 MODEL)
FCC LABEL (VERIZON CAT-M MODEL)
FCC LABEL (AT&T /T-MOBILE CAT-1 MODEL)

DISCOVER YOUR DIGITAL POTENTIAL
5
SPECIFICATIONS
I/O
•Analog input x 4: 0-2.5V, 0-10V / 4-20mA (SW configurable)
•Digital input
•RS485 Half-Duplex
Communication
•4G LTE cellular cloud connectivity
•900MHz RF star-network configuration for multiple pumps
connectivity
•BLE
•GPS
Measurements
•3-Axis vibration monitoring [Inch/Sec]
•Temperature ±5° [°F]
•Battery voltage [V]
EDGE computing
•Radial velocity RMS
•Axial velocity RMS
•3-Axis velocity FFT @ Five selected frequencies
oWhere x = rotation freq. ex. 1x, 2x, 3x, 7x, 10x
•Rotation velocity [RPM]
•Operational hours
Notifications
•Axis velocity RMS threshold cross
•Radial velocity RMS threshold cross
•Velocity amplitude threshold cross in any of the FFT selected
frequencies
•Operational time threshold cross
•Temperature threshold cross
•Analog measurement threshold cross
•Digital input changes or flow frequency threshold cross
Operation modes
•Battery: 1 yr. @ 4 sample/hour and 2 cloud updates per day
•External DC power: 9..24VDC; up to 20 sample/hour and 8 cloud
updates per day
User interface
•Internet browser
•Mobile apps: IoS and Android using BLE for on-site offline device
connectivity
Dimension & build
•3.4”x3.4”x1.9”
•Robust glass filled PP enclosure IP65 comply
•Mounting screws 4x #8-32 x1 inch long
Standards
•FCC Part 15 (see label)
•RoHS comply
Environmental conditions
•Temperature: -22°F/+158°F

DISCOVER YOUR DIGITAL POTENTIAL
6
ASSEMBLY
DIMENSIONS
73.66 (2.9") Typ. x4
(3.4")
(3.4")
(1.9")

DISCOVER YOUR DIGITAL POTENTIAL
7
MOUNTING
Use the #8-32 x 1” screws to secure the VAPOR-C to the monitored equipment (9/64” Allen wrench). If the
device is used as a pump controller or communication gateway, then there is no importance to the orientation;
however, if also used for rotating equipment vibration monitoring then follow the below for the right
orientation.

DISCOVER YOUR DIGITAL POTENTIAL
8
Mounting orientation
Mounting screws
Radial X

DISCOVER YOUR DIGITAL POTENTIAL
9
WIRING
•Use the Allen wrench 5/6” (8mm) to unscrew the cover from the base.
•Open the box, so you have access to the wire’s terminal block
•Run the 6-wire cable through the cable gland in the bottom. For water resistance environment use cable
AMI part#400-0048. If other cable is used, ensure cable outer diameter of 8mm and smooth cable jacket for
proper sealing.
•Connect the wires according to the wiring diagram below

DISCOVER YOUR DIGITAL POTENTIAL
10
Digital input wiring
Signal
Signal
DIN
GND
DIN
GND
Open collector
Dry contact
4-20mA
Sensor
#1 0-10V
Sensor
#4
I/O are functional only when device is connected to external power supply

DISCOVER YOUR DIGITAL POTENTIAL
11
BATTERIES REPLACEMENT
Use Energizer L91 Ultimate Lithium 3 x AA batteries ONLY