Amoonsky AMS-SC359 User manual

LED Video Splicer &Processor
AMS-SC359
User Manual
LED Video Processor
户手册
User’s Manual

Safety Instructions
This symbol prompts the user; the device user manual has important operating and
maintenance instructions.
This symbol warns the user of the equipment inside the enclosure exposed to
hazardous voltages, there is the risk of electric shock.
Note
Read the manual• Read and understand all safety and operating instructions before using the
equipment.
Save the manual• the safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user
information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the
equipment manufacturer because they may be hazardous.
Warning
Power sources • this equipment should be operated only from the power source indicated on the
product.
This equipment is intended to be used with a main power system with a grounded (neutral) conductor.
The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from
the rear of the equipment, or the desktop power module (if detachable), or from the power source
receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or
pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts
inside. To prevent the risk of shock, do not attempt to service this equipment yourself because
opening or removing covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to
prevent overheating of sensitive components inside. These openings must never be blocked by other
objects.
Copyright
Copyright © 2017 The splicing processor and the video processor manufacturers all rights reserved.
Trademarks
VGA and XGA are registered trademarks of IBM Corporation.
VESA is a trademark of the Video Electronics Standards Association.
HDMI logo and High-Definition Multimedia Interface (High-Definition Multimedia Digital Interface) are
HDMI Licensing LLC. Trade marks.

Contents
Introduction................................................................................................................................................................. 1
LED Video Splicing Processor....................................................................................................................1
Panel............................................................................................................................................................................ 2
Rear Panel.......................................................................................................................................................2
Front Panel......................................................................................................................................................3
Menu System..............................................................................................................................................................5
Default Menu....................................................................................................................................................5
Main Menu........................................................................................................................................................ 5
Configuration.............................................................................................................................................................. 6
Output Resolution.......................................................................................................................................... 6
Switch Effect................................................................................................................................................... 7
Black And Freeze...........................................................................................................................................7
User Settings Save and Load..................................................................................................................... 7
VGA Correction.............................................................................................................................................. 8
Language.........................................................................................................................................................8
Lock The Button............................................................................................................................................. 8
Factory Reset................................................................................................................................................. 9
Application................................................................................................................................................................ 10
Multiple Images............................................................................................................................................ 11
Part/Full Display(FS)...................................................................................................................................12
Splicing Operation...................................................................................................................................................14
PIP Function............................................................................................................................................................. 15
Picture In Picture......................................................................................................................................... 17
Keying Color Cutout....................................................................................................................................17

1
Introduction
This manual contains information about how to use, install and configuration the LED video splicing
processor, in addition, also relates to knowledge LED video splicing processor and LED video
systems. If Use the LED video splicing processor, please read this manual carefully.
About LED Video Splicing Processor
The LED splicing processor has three powerful video processing cores, multi-graphics multi-input
smart splicing processor, which can be widely used in performing arts activities, command and control
center, video conferencing, hotels, courts and conference rooms.
The LED splicing processor has 4-channel output, 3-channel for splicing, and 1 channel for
monitoring. Can achieve 3* 1 or 1* 3 channel hybrid splicing, a single product support 7.95 million
pixel user-defined output.
The LED splicing processor can accommodate a wide range of input sources, can access up to 13
video inputs, including 2 DVI, 3 HDMI, 4 AV, 3 VGA and 3G-SDI (optional). Each channel can accept
standard resolution or high resolution video signals, the DVI and VGA can receive up to 1920 × 1200
@ 60Hz resolution input, to meet a variety of high-definition output.
The splicing processor is easy to use, using the key panel and menu system to complete the complex
settings. RS-232 can be used for remote operation. A variety of input interfaces, to meet the different
signal needs. Built-in 4 LED send card installation location to meet the installation requirements of
large-screen system.

2
Panel
Rear panel
Video Input Connector:
● AV1,AV2, AV3, AV4 —Composite video input, BNC connector, support PAL、PAL-M/N、
NTSC、SECAM.
●DVI1, DVI2 —DVI video input. DVI- I/DVI-D connector. support VESA standard video
format.
●HDMI1, HDMI2, HDMI3 —HDMI video input. HDMI - A connector. Support HDMI1.3 /
VESA standard.
●VGA1, VGA2, VGA3 —VGA video input. DB-15 connector. Support VESA standard video
format.
●SDI, SDI-LOOP —SDI video input, loop out. BNC connector.
Video Output Connector:
● CH-A/B/C —DVI video output. DVI-I connector.
● CH-M/Monitor —DVI video output. DVI-I connector. Connect to monitor screen.
RS-232 — Serial communication connector for engineering testing, program burning, PC software
control. Baud rate is 115200bps.
LED Sending Card Slot — Built-in 4 sending card slot.
AC Connector — Use IEC standard power cable，input 100-240 VAC, 50-60Hz.
AC Switcher — power on/off.
Control Connector — Net cable, USB input control.
Audio Connector — Audio output (L1 R1 GND L2 R2).

3
Front panel
LCD Display — displays the parameters and user settings.
Operating button — operate the menu system.
●OK “confirm”
●ESC “exit” or “back”
●Knob press down “OK”, turn right ”+” turn left ”-” adjust the parameters on menu.
INPUTS — including 13 input signal selections, screen testing function, VGA auto correction.
● AV1, AV2, AV3, AV4 —video input selection button.
● VGA1, VGA2, VGA3 —VGA input selection / auto correction button. Keep press
VGA1/2/3 button one more time could enable the auto correction function.
● DVI1, DVI2, HDMI1, HDMI2, HDMI3 SDI – DVI, HDMI, and SDI input selection button.
Indicator light function – the button light on when power on.
(1) Slow flicker：The interval is 1 second and keep flicker – no input signal.
(2) Fast flicker：The interval is 0.3 second – decoding the input signal.
(3) Light on：No flicker – input signal working.

4
FUNCTION — including display model, black output, preset, pip function and switch type.
●FS – part screen display function, set the parameters in SPLICE menu.
●PIP – enable/disable the PIP function, set the parameters in PIP menu.
●FN –enable synchronously switch between CH-A/CH-C, use same input signal.
●Black – output black/freeze screen, select the output in the FUNC menu.
●MODE – load the user settings, support 4 group presetting.
Hint：When PIP function is working, PART/ FREEZE/BLACK/FADE are disabled.

5
Menu System
1. Default menu
OLED will display the input source, output resolution of each channel and other parameters when the
processor startup.
2. Main menu
Main menu display the option of every operation, all the functions could be set in the menu, press
“OK” to enable the main menu when the processor is in default menu.
Option
Description
OUTPUT
Set output resolution for each channel
SPLICER
Set splicing parameters and part display, support equal/unequal splicing.
LAYER
Set PIP parameters etc.
PICTURE
Set the brightness, contrast, etc.
FUNCTION
Set language, user settings save and load
SYSTEM
Set system function, system version, factory reset etc.
Operation: press the “OK” button or Knob could enable the main menu, “ESC” is return button, turn

6
right or turn left the knob could adjust the parameters.
Configuration
1. Output Resolution
The default output resolution of the processor is 1920x1080/60Hz, user need to set the output
resolution according to the display; this is the first setup of using the processor.
(1) Set output according to standard resolution:
① ②
③ ④
(2)The processor also supports user-defined output resolution:
① ②
③ ④

7
Hints：After the user resets the output resolution, the system will reset all the parameters of
the splice menu to ensure the consistency of the data. The user-adjusted resolution can only
be smaller than the currently selected resolution. The horizontal start value and the vertical
start value cannot be adjusted when the resolution of the fine adjustment is equal to the
currently selected resolution.
2. Switch Effect
The processor support seamless switch and fade-in/fade-out switch.
① ②
3. Black And Freeze
The processor could output black screen and freeze the screen, this two functions use one button
“BLACK” on the front panel, this shortcut key could be configurated to “black” or “freeze”.
① ②
4. User Settings Save And Load
The user settings could be save in the processor to avoid reset when use same operation, the
settings could be loaded from the processor easily. 4 groups are available for the user setting.
(1) Save Mode
This function could save all the parameters which configured by users.
① ②

8
⑤ ④
There are 4 groups [1] ~ [4] in the sub menu, when the group is no data, it shows ☆, otherwise display
★The data could be overwrite by user.
(2) Load Mode
There are two different ways to load the user settings, use menu or shortcut key.
①Shortcut key, press the “1” “2” “3” “4” button on the front panel
②Load from menu:
① ②
③ ④
5. VGA Correction
The processor could correct the VGA input automatically including color, image size and position.
User also could correct the VGA input manually in two different ways.
①press “VGA/AUTO twice, the processor will correct the VGA video.
②Use the correction function in menu:
① ②

9
③auto ③manually
Hint: When the processor no VGA signal input, the function of correction is disabled, it will
be better to set different output resolution when user VGA1, VGA2, VGA3 at same time.
6. Language
The processor support two languages Chinese and English, could be changed in menu:
① ②
7. Lock the Button
The processor supports button lock to avoid miss operation. Lock in the menu:
① ②
Keep press the “ESC” button 3 seconds to unlock the button.
8. Factory Reset
The processor support factory reset if the user parameters are wrong or misses operation, set in
menu.
① ②

10
Warning: factory reset will delete all the user parameters, please be careful to use.
Application
The processor support large splicing output, the maximum width output resolution is 11520 pixels or
maximum height is 4608. Support frame synchronization.
Hints：Please make sure the output resolution of A, B and C is configured.
1. Multiple images
(1).three screen display three images.
Step: 1. Connect output CH-A to screen 1, CH-B to screen 2, CH-C to screen 3 by DVI cable.
2. Select input source for CH-A, CH-B, CH-C, for example HDMI1, VGA3, CV4.
3. Configure the output resolution in menu of led video processor.
① ②

11
③ ④Output A
④Output B ④Output C
(2). three screen display one image.
Step: 1. Connect output CH-A to screen 1, CH-B to screen 2, CH-C to screen 3 by DVI cable.
2. Select same input source for CH-A, CH-B, CH-C, for example HDMI1
3. Configure the output resolution in menu as the last example 1.
4. Configure the splicing parameters in menu.
① ②
③ ④Splice A

12
④Splice B ④Splice C
2. Part/Full display
Part/Full display is based on the splicing function, it could display part of screen for example the
user just need to display the red part as follow. Set the parameters in the menu then use the “PART”
button on the front panel to enable or disable this function.
Full display Part display
The parameters of part display area could be set automatically or configurable by user, when the
“Part Mode” is “Auto” the display area is unchangeable.
① ②
③ ④

13
Splice Wizards
The splice wizard is designed for the multiple screens splicing, make the setting easy for user.
① ②
③ ④
⑤there are 7 splice mode for selection to quickly set the parameters
No.1: 3 screen display one picture in horizontal No.2: 3 screen display two pictures in horizontal
No.3: 3 screen display three pictures in horizontal No.4: 2 screen display one picture in horizontal

14
No.5: 2 screen display three pictures in horizontal
No.6: 3 screen display one picture in vertical No.7: 3 screen display two pictures in vertical
⑥set the proportion of picture.
Two pictures Three pictures
⑦

15
PIP function
1. Picture in Picture
Picture in picture could display two different input source in the same screen. That means in the
normal displaying of the main input, inserted one or more compressed sub-screen in order to monitor
other input. When working in picture-in-picture mode, the user needs to provide at least two signal
input, and make appropriate settings for PIP. This function can also achieve the effect of POP, it is a
special application of PIP.
(1) PIP could be enabling on the front panel by press “PIP” button.
(2) Set the PIP display size and position, PIP frame and transparency in menu.
① ②
Output MAIN Output A
Output B Output C

16
Hint：The fade-in/fade-out and seamless switching will be disabled, when PIP is working.
(3) The PIP function doesn’t work between the same type signal, please check the following table
which show the conflict.
Main source
AV 1
AV2
AV3
AV4
VGA1
VGA2
DVI1
DVI2
HDMI1
HDMI2
SDI
PIP
AV1
√
×
×
×
√
√
√
√
√
√
√
AV2
×
√
×
×
√
√
√
√
√
√
√
AV3
×
×
√
×
√
√
√
√
√
√
√
AV4
×
×
×
√
√
√
√
√
√
√
√
VGA1
√
√
√
√
√
×
√
√
√
√
√
VGA2
√
√
√
√
×
√
√
√
√
√
√
DVI1
√
√
√
√
√
√
√
×
×
×
√
DVI2
√
√
√
√
√
√
×
√
×
×
√
HDMI1
√
√
√
√
√
√
×
×
√
×
√
HDMI2
√
√
√
√
√
√
×
×
×
√
√
SDI
√
√
√
√
√
√
√
√
√
√
√

17
2. Keying Color Cutout
This function could cutout the red, green, blue, black and white color from input signal in order to
achieve some simple special effects processing and superimposed subtitles. For example as follow:
PIP input Main input Output effects
① ②
③