AMP Lighting AAL-1019-4 Series Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® EscherPro MR16 Spotlight
AAL-1019-4-B-BZ

AMP® EscherPro MR16 Spotlight
AAL-1019-4-X-XX
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
A. (1) Fixture
B. (1) Stake
Install Stake
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
harmmering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP® EscherPro MR16 Spotlight
AAL-1019-4-X-XX
Install Fixture to Stake
Wire Connection
Clear away an area in the
ground at the wireway slot on
top of the stake. Lay the xture
pigtail into the wireway slot
and attach the xture onto the
stake. Tighten until snug.
Fixture
Ground
Supply Wires
Wireway Slot
Soil
Stake
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP® EscherPro MR16 Spotlight
AAL-1019-4-X-XX
Remove Glare Guard
Remove Lens
Loosen the set screw and remove
the glare guard from the xture.
REMOVE
Fixture
Set Screw
Glare Guard
Rotate the lens to remove it
from the xture.
REMOVE
ROTATE
Fixture
Lens

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP® EscherPro MR16 Spotlight
AAL-1019-4-X-XX
Install MR16 Bulb
ROTATE
Insert MR16 bulb with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR16 Bulb
Socket
Place the lens back onto the
xture and rotate it until it is
secured properly.
Fixture
Lens
7
Install MR16 Bulb

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Bulb
8
Install Glare Guard
Install the glare guard back
onto the xture and
secure with previously
removed set screw.
Fixture
Set Screw
Glare Guard
9
Adjust Lamp Direction
Using the provided Allen wrench,
loosen the knuckle and adjust the
xture to your desired direction.
Once your desired direction is
achieved, tighten the knuckle
into place.
Fixture
Allen Wrench
Screw
Remove the glare guard and the lens to expose the MR16 bulb and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the lens and the glare guard.
IMPORTANT: MR16 bulb must be protected from moisture and dust at all
times. Always reinstall the lens and the glare guard when removed.

IS-AAL-1019-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com