AMP Lighting ONE HydraPro AWL-5010IR-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ

AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ
Important: Please Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
!
www.amplighting.com
–2–
Important Safety Instructions
!
This xture is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions
may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3 me-
ters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
7. IR dimmability with our Design-Master™ Remote Control.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
–3–
Package Contents
Product Dimensions
A. (1) Fixture body
Parts Required (sold separately)
A. Mounting Accessory
2”
4”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ
Install Stake
1
Install Fixture to Stake
2
Determine the desired location
for mounting the xture. Ham-
mer the stake into the ground
until ange of stake is ush to
grade. To avoid damage to the
stake, place a board on top of
the stake while hammering.
NOTE: If the ground is hard and
the stake is dicult to install,
make a crosscut in the ground
using a at shovel.
Board
Stake
Soil
Ground
Clear away an area in the
ground for the stake. Lay
the luminaire pigtail into the
cleared area and screw the
xture onto the stake. Tight-
en until snug.
Ground
Fixture
Pigtail
Soil
Stake

[email protected] • 813.978.3900
–5–
Wire Connections
3
Install/Replace Glare Guard
Remove Faceplate
1
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold seperately), connect the leads from the luminaire to the main
supply cable.
Main Supply
Cable
Pigtail
Wire Connectors
Loosen the screws and remove the
faceplate from the xture.
Screw
Faceplate
Fixture

–6–
www.amplighting.com
–6–
INSTALLATION & MAINTENANCE GUIDE
AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ
Install Glare Guard
2
Remove Faceplate and Lens
1
Attach the glare guard onto the
xture and secure it with the
screws previously removed.
Now you can power on the
system, the light is 2700K
and the optic is 60 degrees as
default.
Fixture
Screw
Glare Guard
Install/Replace Opc
Loosen all screws on the faceplate.
Remove the faceplate and lens from
the xture.
xture
Screw
Faceplate
Lens

–6––6–
[email protected] • 813.978.3900
–7–
Replace Optic
2
IR Remote (Oponal)
An IR Remote is optional for this xture. The IR remote requires two AAA
batteries.
Reinstall Lens and Faceplate
3
xture
Screw
Loosen the screws and remove
the optic from the xture.
Install the new optic in the
xture. Make sure that you have
the optic properly aligned over
the LED board before tightening
down. Improper alignment when
tightening the screws can cause
the optic to break.
Optic
Place the lens and faceplate back
onto the xture. Secure them with
previously removed screws. Tighten
with a screwdriver.
xture
Screw
Faceplate
Lens
Remove the Battery Compartment Cover
1
1
2
3
Press the tab and rotate the battery
compartment cover to remove it
from the IR Remote.
Ta b
Cover
Backing
IR Remote

–8–
www.amplighting.com
–8– –9–
INSTALLATION & MAINTENANCE GUIDE
AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ
Install Two AAA Batteries
2
+
-
+-
Place two AAA batteries into the
battery compartment properly.
AAA Battery Battery
Compartment
Backing
IR Remote
Install the Battery Compartment Cover
3
1
2Place the battery compartment
cover back onto the IR Remote.
Ta b
Cover
Backing
IR Remote

[email protected] • 813.978.3900
–9–
IR Remote Functions
4
OFF ON
R B
W
G
FLASH
FADE
SMOOTH
STROBE
2
3
4
1
5
6
7
8
1. On
2. O
3. Brightness Control
4. 16 color selections
5. Flash
A. Mode 1: Repeats Red,
Green, Blue + color cycle for
1 second duration of each of
the seven colors within this
mode.
A. Mode 2: Hit ash a second
time and this mode slowly
blends the same seven col-
ors from mode one, mixing
them together.
6. Strobe
A. Mode 1: Pick any color on the remote, then press strobe and that
color will strobe every second alternating between on and o.
A. Mode 2: Hit strobe a second time and this mode will strobe a
blended white color at the same speed as before.
7. Fade
A. Mode 1: Pick any color on the remote, then press fade and that
color will slowly fade on and o every second.
A. Mode 2: Hit fade a second time and it will fade a blended white
color on and o at the same speed as before.
8. Smooth
A. Mode 1: Repeats a ash cycle of Red, Green, and Blue only.
A. Mode 2: Hit smooth a second time and this mode slowly blends
Red, Green, and Blue only; on and o at the same speed.

–10–
www.amplighting.com
–10–
INSTALLATION & MAINTENANCE GUIDE
AMP®ONE RGBW HydraPro™ Single Source LED In-Grade Light (Dimmable)
AWL-5010IR-B-BZ

[email protected] • 813.978.3900
–11–

Specications and product details subject to change without notice.
© Copyright 2022, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com