AMP Lighting ArchPro APL-3027-4-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® ArchPro Path & Area Light (Lamp-Ready)
APL-3027-4-B-BZ
–1–

AMP®ArchPro Path & Area Light (Lamp-Ready)
APL-3027-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and in-
structions may result in serious injury, property damage and void the warran-
t y.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture
23”
9.5”
5.5”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
Remove Lens
1
AMP®ArchPro Path & Area Light (Lamp-Ready)
APL-3027-4-B-BZ
Loosen the lens and
remove it from the
xture body.
Fixture Body
Lens
Install Bulb
2
Insert bulb with correct watt-
age and type marked on xture
label and push into place.
CAUTION: Do not exceed
maximum wattage marked on
xture label.
Fixture Body
Bulb
Install Lens
3
Thread the lens back onto the
xture body and hand tighten
until snug.
Fixture Body
Lens

–5–
Install Stake
4
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on
top of the stake while hammer-
ing.
Note: If the ground is hard and
the stake is dicult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
Install Fixture Body to Stake
5
Pass the xture wire through
the center hole of the stake.
Thread the xture body on to
the stake and hand tighten until
snug.
Fixture Body
Fixture Wire
Ground
Soil
Stake

[email protected] • 813.978.3900
–6–
INSTALLATION & MAINTENANCE GUIDE
AMP®ArchPro Path & Area Light (Lamp-Ready)
APL-3027-4-B-BZ
Wire Connections
6
Strip both leads from the xture body. Using two wire connectors (sold
separately), connect leads from xture body to the main supply cable
leads.
Pigtail
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors
Adjust Shade Direction
7
NOTE: Do not rotate the shade
a full 3600. This will damage the
internal wiring.
Using the Allen wrench, loosen
the set screw on the stem and
adjust the hat to your desired
angle. Once your desired angle
is achieved, tighten the set
screw using the Allen wrench to
secure the shade direction.
Allen Wrench
Stem
ROTATE
Shade
Set Screw

–7–
Install/Replace Bulb
Reverse Step 1 - Step 3 to expose the bulb and replace it with correct watt-
age and type marked on xture label. And then reinstall the lens.
IMPORTANT: Bulb must be protected from moisture and dust at all times.
Always reinstall the lens when removed.

Specications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
–8–