AMP Lighting Solarium ASAL-1026-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Solar Landscape Lighting
AMP® Solarium Solar Motion Sensing Spotlight
ASAL-1026-B-BZ

AMP®Solarium Solar Motion Sensing Spotlight
ASAL-1026-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
Package Contents
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
5. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
A. (1) Fixture

[email protected] • 813.978.3900
Product Dimensions
–3–
1
2.5”
5.25”
6”
4.25”
11.25”
6.5”
Test Solar Light
Place the solar light on a non-
abrasive surface with the solar panel
face down. Press the ON/OFF switch
on the back of the xture body. Wave
your hand in front of the sensor to
test the xture.
Now you can proceed to the next
steps of installation.
Non-Abrasive Surface
Solar
Panel
1
2
3
Sensor
Push On/Off Switch

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP®Solarium Solar Motion Sensing Spotlight
ASAL-1026-B-BZ
Install Stake
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Stake
Install Fixture Body to Stake
Thread the xture body on to the
stake. Hand tighten until snug.
Make sure the sensor is facing the
desired area to be monitored during
installation.
NOTE: The light will illuminate for 15
seconds after the sensor trips. The sensor
distance is 23ft with 1200 detection angle.
Fixture Body
Ground
Soil
Stake
Sensor

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®Solarium Solar Motion Sensing Spotlight
ASAL-1026-B-BZ
Adjust Luminaire Direction
Adjust the sensor by using the
lock screw.
Adjust the luminaire angle by
using the knuckle.
Luminaire
Knuckle
Lock Screw
1
2
2
1
Adjust Solar Panel Direction
Solar Panel
Adjust the solar panel piece
forward and backwards by using
the hand screw.
You can also take the solar panel
piece itself and rotate it in any
direction you need to face the sun.
Hand Screw

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP®Solarium Solar Motion Sensing Spotlight
ASAL-1026-B-BZ
Replace Sensor
If necessary, remove the cover to
replace the sensor. Always install the
cover back to protect the sensor.
Sensor

–6––6–
[email protected] • 813.978.3900
–7–

IS-ASAL-1026-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com