AMP CDR1 User manual

For Technical Support, Contact AMP
at [phone] (9 am - 5 pm PST)
or [e-mail]
Advanced Microwave Products
PO Box 1437
2465 Old Highway 40 West, Suite 200
Verdi, NV 89439
Connect antennas to SMA connectors
Connect video monitor/recorder to BNC connector
Connect audio/data outputs to 3.5mm stereo jack
and/or the MDM-9S connector (if applicable)
Set Conguration *see reverse side
STEP
STEP
STEP
STEP
STEP
STEP
Connect power/communications inputs to the
MDM-9P connector *see reverse side
Check RSSI meters to conrm a signal is being received
Note When setting up your system, the transmit and receive
antennas should be greater than 25 feet apart to
prevent serious damage to or destruction of the
receiver’s front end
CDR1 Receiver Quick Start Guide

AQS-CDR1-D
How to Set Your Receiver Conguration
Wiring Your CDR1 Receiver
(Audio/Data Connections are Dependent on Conguration )
BNC Female
Video Output (Connect to Monitor)
3.5mm Stereo Jack
Audio Out
SMA Female
RF Input (Connect to Antenna)
SMA Female
RF Input
(Connect to Antenna)
Ground
Audio (L)
Audio (R)
MDM-9P
Power & Programming
1:
2:
3:
4:
5:
6:
7:
8:
9:
+11 to 16 VDC Input
Ground
Ground
Ground
12VDC Out
NC/TX Comm-
TX Comm+
RX Comm+
NC/RX Comm-
1 5
6 9
MDM-9S
Audio/Data Input
1:
2:
3:
4:
5:
6:
7:
8:
9:
Audio 1 -10dBV
Audio 1 +4dBu
Ground
Audio 2 -10dBV
Audio 2 +4dBu
Ground
TTL Data
RS232 Data
Ground
15
69
NC = No Connection
Front
Back
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 8 MHz QPSK 1/2 1/4 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
2 8 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
3 8 MHz QPSK 5/6 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
4 8 MHz 16QAM 2/3 1/4 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
5 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz 16QAM 5/6 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 7/8 1/16 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 2.5 MHz QPSK 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
2 2.5 MHz QPSK 1/3 1/16 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
3 2.5 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
4 2.5 MHz QPSK 2/3 1/16 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
5 2.5 MHz 16QAM 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz QPSK 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
Config Bandwidth Modulation FEC Guard Video (per Default) Audio Data Input Data Rate
1 1.25 MHz QPSK 1/3 1/8 NTSC (15 fps) or PAL (12.5 fps) 8 kHz, 16-Bit, Stereo Same as Comms 9600
2 1.25 MHz QPSK 2/3 1/16 NTSC (30 fps) or PAL (25 fps) 8 kHz, 16-Bit, Stereo Same as Comms 9600
3 2.5 MHz QPSK 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
4 2.5 MHz QPSK 2/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
5 2.5 MHz 16QAM 1/3 1/8 NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms 9600
6 8 MHz QPSK 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
7 8 MHz 16QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
8 8 MHz 64QAM 3/4 1/8 NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms 9600
6/7/8 DVB-T Bandwidth
Narrowband Bandwidth
Ultra-Narrowband Bandwidth
The CDR1 Receiver has two modes for conguring the unit: Local Mode and Remote Mode . Local Mode
utilizes 5 buttons for conguration settings and frequency selection. To change the frequency or conguration
preset, press the enter button then select the digit you want to change by using the left/right
buttons the digit will ash when selected. Use the up/down arrows to change the selected digit.
When you are done press the enter button to save and activate the settings.
The CONFIG allows you to select one of 8 conguration presets as
shown in the tables below. The CDR1 can only be programmed when it
is set to conguration“0”which is programming mode. “Pr0G” is
displayed on the 4, seven segment displays to the left when in
programming mode.