Ampetronic ATT100-T42 User manual

The ATT100-T42 is designed to interface a 100V line speaker system to a
balanced line-level input such as those found on some Ampetronic loop
drivers. The unit provides a transformer isolated attenuation of 40dB.
Restrictions on usage
The ATT100-T42 is not suitable for use with unbalanced and microphone
inputs. It should only be connected to inputs intended for balanced line-level
signals.
1. Output connection.
The ATT100-T42 is terminated in a 6.3mm 3 pole jack plug. This should be
plugged directly into the balanced line input of the Ampetronic loop driver.
Note the restrictions listed above.
Under no circumstances should the output be extended, not even using a
screened cable. The extended connection would be susceptible to
interference.
2. 100V line connection
The 100V speaker line should be connected to the 3-pin input plug as shown
below.
Plug into ATT100-T42.
Adjust Input Gain on amplifier as required.
ATT100-T42
Adapter
+
-
100V
LINE
SAFETY
EARTH
(IF FITTED)
INSIDE VIEW OF CONNECTOR
}
Safety Notice
The ATT100-T42 contains connections to speaker systems which may carry
hazardous voltages. If any damage to the unit is visible do not use the ATT100-
T42, but switch off all attached systems and disconnect the unit from them
before switching on again. Never attempt to open or modify the unit.
Warranty Information
ATT100-T42 is designed and manufactured in England by Ampetronic Ltd.
DECLARATION OF CONFORMITY
Manufacturer: Ampetronic Ltd.
Address: Northern Road, Newark,
Nottinghamshire, NG24 2ET.
United Kingdom.
Declares that the product:
Description: Input Adapter
Type Name: ATT100-T42
December 2011
This product carries a five year parts and labour warranty from date of
shipment from Ampetronic. To qualify for the five year warranty, the product
must be registered at www.ampetronic.com (products/warranty), without which
the warranty will be valid for two years only.
The warranty could be invalidated if the instructions in this handbook are not
followed correctly, or if the unit is misused in any way.
Conforms to the following Directive(s) and Norm(s):
Directive 2004/108/EC
EMC: EN55103-1 : 2009 Emission
EN55103-2 : 2009 Immunity
Directive 2006/95/EC
Safety: EN60065 : 2002
Date:
J.R. Pieters
Managing Director
Ampetronic Ltd.
UP13008-6
Ampetronic Ltd,
Northern Road, Newark,
Nottinghamshire, NG24 2ET
United Kingdom
Tel: [phone] Fax: [phone]
www.ampetronic.com Email: [email protected]

The ATT100-T42 is designed to interface a 100V line speaker system to a
balanced line-level input such as those found on some Ampetronic loop
drivers. The unit provides a transformer isolated attenuation of 40dB.
Restrictions on usage
The ATT100-T42 is not suitable for use with unbalanced and microphone
inputs. It should only be connected to inputs intended for balanced line-level
signals.
1. Output connection.
The ATT100-T42 is terminated in a 6.3mm 3 pole jack plug. This should be
plugged directly into the balanced line input of the Ampetronic loop driver.
Note the restrictions listed above.
Under no circumstances should the output be extended, not even using a
screened cable. The extended connection would be susceptible to
interference.
2. 100V line connection
The 100V speaker line should be connected to the 3-pin input plug as shown
below.
ATT100-T42
Adapter
+
-
100V
LINE
SAFETY
EARTH
(IF FITTED)
INSIDE VIEW OF CONNECTOR
}
Plug into ATT100-T42.
Adjust Input Gain on amplifier as required.
Safety Notice
The ATT100-T42 contains connections to speaker systems which may carry
hazardous voltages. If any damage to the unit is visible do not use the ATT100-
T42, but switch off all attached systems and disconnect the unit from them
before switching on again. Never attempt to open or modify the unit.
Warranty Information
ATT100-T42 is designed and manufactured in England by Ampetronic Ltd.
DECLARATION OF CONFORMITY
Manufacturer: Ampetronic Ltd.
Address: Northern Road, Newark,
Nottinghamshire, NG24 2ET.
United Kingdom.
Declares that the product:
Description: Input Adapter
Type Name: ATT100-T42
December 2011
This product carries a five year parts and labour warranty from date of
shipment from Ampetronic. To qualify for the five year warranty, the product
must be registered at www.ampetronic.com (products/warranty), without which
the warranty will be valid for two years only.
The warranty could be invalidated if the instructions in this handbook are not
followed correctly, or if the unit is misused in any way.
Conforms to the following Directive(s) and Norm(s):
Directive 2004/108/EC
EMC: EN55103-1 : 2009 Emission
EN55103-2 : 2009 Immunity
Directive 2006/95/EC
Safety: EN60065 : 2002
Date:
J.R. Pieters
Managing Director
Ampetronic Ltd.
UP13008-6
Ampetronic Ltd,
Northern Road, Newark,
Nottinghamshire, NG24 2ET
United Kingdom
Tel: [phone] Fax: [phone]
www.ampetronic.com Email: [email protected]