Amphenol RJSMLAC 8MG CAPS User manual

8MG – CLI UM rev. 2.2 Page 1 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
Amphenol
RJ-Switch
IP67 rugged Ethernet Managed Switch
- CLI U er Manual -
CLI U er Manual
This manual applies to the following products:
•RJSMLAC 8MG CAPS (options)
•RJSMLAC 8MG CAPS VAC (NAV)(options)
•RESMLAC 8MG CAPS (options)
Rugged IP67/68 Managed Gigabit Ethernet Switch
Revision
Date Modifications
1 April 04, 2012 Initial document
2 December 11,2013 Updated screen shots
2.1 December 07, 2016 Added P/N RJSMLAC-8MG-CAPS-VAC (NAV)
/ No change in the content /
2.2 May 09, 2018 Removed RES-SCE-8MG

8MG – CLI UM rev. 2.2 Page 2 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
TABLE OF CONTENTS
Table of Contents............................................................................................................................................................................... 2
Command Line Interface.......................................................................................................................................................................... 4
Command Line Overview ........................................................................................................................................................................ 4
Detailed Command Description ............................................................................................................................................................... 7
System Commands ................................................................................................................................................................................... 8
System Configuration........................................................................................................................................................................... 8
System Restore Default ........................................................................................................................................................................ 8
System Name ........................................................................................................................................................................................ 8
System Reboot ...................................................................................................................................................................................... 8
System SNMP ....................................................................................................................................................................................... 9
System Trap.......................................................................................................................................................................................... 9
System Readcommunity........................................................................................................................................................................ 9
System Writecommunity ....................................................................................................................................................................... 9
System Trapcommunity ........................................................................................................................................................................ 9
Console Commands................................................................................................................................................................................ 10
Console Configuration....................................................................................................................................................................... 10
Console Password.............................................................................................................................................................................. 10
Console Timeout................................................................................................................................................................................. 10
Console Prompt.................................................................................................................................................................................. 10
Port Commands...................................................................................................................................................................................... 11
Port Configuration............................................................................................................................................................................. 11
Port Mode .......................................................................................................................................................................................... 11
Port Flow Control.............................................................................................................................................................................. 11
Port State ........................................................................................................................................................................................... 12
Port MaxFrame.................................................................................................................................................................................. 12
Port Statistics ..................................................................................................................................................................................... 12
port VeriPHY...................................................................................................................................................................................... 13
MAC Table Commands ......................................................................................................................................................................... 13
MAC Configuration ........................................................................................................................................................................... 13
MAC Add............................................................................................................................................................................................ 13
MAC Delete........................................................................................................................................................................................ 14
MAC Lookup ...................................................................................................................................................................................... 14
MAC Table ......................................................................................................................................................................................... 14
MAC Flush ......................................................................................................................................................................................... 15
MAC Age Time ................................................................................................................................................................................... 15
VLAN Commands.................................................................................................................................................................................. 15
VLAN Configuration .......................................................................................................................................................................... 15
VLAN Add .......................................................................................................................................................................................... 15
VLAN Delete ...................................................................................................................................................................................... 16
VLAN Lookup..................................................................................................................................................................................... 16
VLAN Aware....................................................................................................................................................................................... 16
VLAN PVID........................................................................................................................................................................................ 16
VLAN Frame Type.............................................................................................................................................................................. 17
Aggregation/trunking Commands .......................................................................................................................................................... 17
aggregation Configuration ................................................................................................................................................................ 17
Aggregation Add ................................................................................................................................................................................ 17
Aggregation Delete ............................................................................................................................................................................ 17
Aggregation Lookup........................................................................................................................................................................... 18
Aggregation Mode.............................................................................................................................................................................. 18
Lacp Commands..................................................................................................................................................................................... 18
LACP Configuration .......................................................................................................................................................................... 18
LACP Mode........................................................................................................................................................................................ 19
LACP Key........................................................................................................................................................................................... 19
RSTP Commands ................................................................................................................................................................................... 19
RSTP Configuration........................................................................................................................................................................... 19

8MG – CLI UM rev. 2.2 Page 3 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
RSTP Sysprio ..................................................................................................................................................................................... 19
RSTP Hellotime.................................................................................................................................................................................. 20
RSTP Maxage..................................................................................................................................................................................... 20
RSTP Fwddelay.................................................................................................................................................................................. 20
RSTP Version ..................................................................................................................................................................................... 21
RSTP Mode ........................................................................................................................................................................................ 21
RSTP Aggr ......................................................................................................................................................................................... 21
RSTP Edge ......................................................................................................................................................................................... 21
RSTP Pathcost ................................................................................................................................................................................... 22
RSTP Mcheck ..................................................................................................................................................................................... 23
RSTP Status........................................................................................................................................................................................ 23
RSTP Statistics ................................................................................................................................................................................... 23
User Group Commands.......................................................................................................................................................................... 23
User Group Configuration ................................................................................................................................................................. 23
User Group Add ................................................................................................................................................................................. 24
User Group Delete ............................................................................................................................................................................. 24
User Group Lookup ........................................................................................................................................................................... 24
QoS Commands ..................................................................................................................................................................................... 24
QoS Configuration ............................................................................................................................................................................. 25
QoS Mode .......................................................................................................................................................................................... 25
QoS Default........................................................................................................................................................................................ 25
QoS Tagprio ....................................................................................................................................................................................... 25
QoS DiffServ ...................................................................................................................................................................................... 26
QoS Userprio ..................................................................................................................................................................................... 26
Mirror Commands.................................................................................................................................................................................. 26
IGMP snooping commands.................................................................................................................................................................... 27
Debug Commands.................................................................................................................................................................................. 29
IP Commands......................................................................................................................................................................................... 29
Dot1X Commands.................................................................................................................................................................................. 31
Filter Commands.................................................................................................................................................................................... 33
Examples.................................................................................................................................................................................................... 35
FACTORY DEFAULT CONFIGURATION ............................................................................................................................................... 37
WEB INTERFACE ..................................................................................................................................................................................... 38
WEB INTERFACE CONFIGURATION..................................................................................................................................................... 39

8MG – CLI UM rev. 2.2 Page 4 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
C OMMAND L INE I NTERFACE
The Ethernet switch Command Line Interface (CLI) is used for out-of-band control of the Ethernet
switch. It provides the ability to customize confi urations and status monitorin .
C OMMAND L INE O VERVIEW
? Help Up Exit
System Confi uration [all]
System Restore Default [keepIP] System Name
[<name>]
System Reboot
System SNMP [enable|disable] System Trap
[<IP Address>]
System Readcommunity [<community strin >]
System Writecommunity [<community strin >] System
Trapcommunity [<community strin >] Console Confi uration
Console Password [<password>] Console
Timeout [<timeout>]
Port Confi uration [<portlist>]
Port Mode [<portlist>] [<speed>]
Port Flow Control [<portlist>] [enable|disable] Port State
[<portlist>] [enable/disable]
Port MaxFrame [<portlist>] [<framesize>|reset]Port Statistics [<portlist>]
[clear]
Port VeriPHY [<portlist>] [full|anomaly|termination] MAC Confi uration
MAC Add <macaddress> <portlist>|none [<vid>] MAC Delete
<macaddress> [<vid>]
MAC Lookup <macaddress> [<vid>] MAC table
<vidlist>
MAC Flush
MAC A etime [<a etime>]
VLAN Confi uration [<portlist>] VLAN Add
<vidlist> [<portlist>] VLAN Delete <vidlist>
VLAN Lookup <vidlist>
VLAN Aware [<portlist>] [enable|disable]
VLAN PVID [<portlist>] [<vid>|none]
VLAN Frame Type [<portlist>] [all|ta ed] A r
Confi uration
A r Add <portlist> A r Delete
<portlist> A r Lookup <portlist>
A r Mode [smac|dmac|xor]

8MG – CLI UM rev. 2.2 Page 5 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
Lacp Confi uration [<portlist>]
Lacp Mode [<portlist>] [enable|disable] Lacp Key
[<portlist>] [<key>|auto]
Lacp Status
Lacp Statistics
Rstp Confi uration [<portlist>] Rstp sysprio
[<sysprio>]
Rstp hellotime [<secs>]
Rstp maxa e [<hops>] Rstp
fwddelay [<secs>]
Rstp version [normal|compat]
Rstp Mode [<portlist>] [enable|disable] Rstp A r
[enable|disable]
Rstp Ed e [<portlist>] [enable|disable]
Rstp Pathcost [<portlist>] [<pathcost>|auto] Rstp mcheck
<portlist>
Rstp Status
Rstp Statistics
User Group Confi uration
User Group Add < rouplist> [<portlist>] User Group
Delete < rouplist>
User Group Lookup < rouplist> QoS
Confi uration [<portlist>]
QoS Mode [<portlist>] [ta |iptos|port|diffserv|L4] QoS Default
[<portlist>] [low|hi h]
QoS Ta prio [<portlist>] [<ta priolist>] [<class>]
QoS Tosprecedence [<portlist>] [<tosprecedencelist>] [<class>] QoS DiffServ
[<portlist>] [<dscplist>] [low|hi h]
QoS L4 Default [<portlist>] [<class>]
QoS L4 Match [<portlist>] [<class>]
QoS L4 Add [<portlist>] <UDP/TCP portlist>
QoS L4 Delete [<portlist>] <UDP/TCP portlist>
QoS L4 List [<portlist>]
QoS Userprio [<portlist>] [<ta prio>]
QoS Shaper [<portlist>] [enable|disable] [<rate>] QoS Policer
[<portlist>] [enable|disable] [<rate>]
QoS Storm Control [<portlist>] [enable|disable] [<rate>]
Mirror Confi uration
Mirror Port [<port>]
Mirror Source [<portlist>] [enable|disable] IP Confi uration
IP Setup [<ipaddress> [<ipmask> [<ip ateway>]]] [<vid>] IP Mode
[enable|disable]
IP ARP

8MG – CLI UM rev. 2.2 Page 6 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
IP DHCP [enable|disable] Dot1x
Confi uration
Dot1x Mode [enable|disable]
Dot1x State [<portlist>] [Auto|ForceAuthorized|ForceUnauthorized] Dot1x Server [<IP
Address>]
Dot1x UDP Port [<value>]
Dot1x Secret [<Shared Secret>] Dot1x
Statistics [<portlist>]
Dot1x Reauthenticate [<portlist>] [now] Dot1x
Parameters [<parameter>] [<value>]
Debu Loopback [int|ext]
IGMP Confi uration
IGMP Status
IGMP Groups <vidlist>
IGMP Mode [enable|disable]
IGMP State <vidlist> [enable|disable] IGMP Querier
<vidlist> [enable|disable]
IGMP Router ports [<portlist>] [enable|disable] IGMP Unre istered
Flood [enable|disable]

8MG – CLI UM rev. 2.2 Page 7 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
D ETAILED C OMMAND D ESCRIPTION
Some of the commands have optional parameters. If the optional parameter is omitted, a default value
may be used
or the command may display the current settin (i.e. function as a et command).
Example 1, omitted parameter interpreted as display command:
Syntax:
System Name [<name>]
>system name <enter>
System Name: RJSMLAC-8MG-CAPS
Example 2, omitted parameter interpreted as default value (VLAN
ID 1):
Syntax:
MAC Add <macaddress> <portlist> [<vid>]
>mac add 010203ABCDEF 16 <enter>
The followin sections list the individual commands by showin the syntax and a description of each
command.

8MG – CLI UM rev. 2.2 Page 8 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
S YSTEM C OMMANDS
System Configuration
Syntax:
System Confi uration [all] Description:
Show system name, software version, hardware version and mana ement MAC
address. Optionally show the full confi uration
[all]: Show the total switch confi uration (default: System confi uration only).
System Restore Default
Syntax:
System Restore Default [keepIP]
Description:
Restore factory default confi uration.
[keepIP]: Preserve IP confi uration (default: Not preserved).
System Name
Syntax:
System Name [<name>]
Description:
Set or show the system name. The empty strin (“”) clears the system name.
[<name>]: Strin of up to 16 characters (default: Show system name).
System Reboot
Syntax:
System Reboot
Description:
Reboot the switch.

8MG – CLI UM rev. 2.2 Page 9 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
System SNMP
Syntax:
System SNMP [enable|disable]
Description:
Activate or deactivate SNMP.
[enable|disable]: Enable/disable SNMP (default: Show SNMP mode).
System Trap
Syntax:
System Trap [<IP Address>]
Description:
Set or show SNMP traps destination.
[<IP Address>]: IP address to send traps to. 0.0.0.0 disables traps (default: Show trap destination).
System Readcommunity
Syntax:
Readcommunity [<community strin >]
Description:
Set or show SNMP read community strin .
[<community strin >]: New community strin . (default: Show current value).
System Writecommunity
Syntax:
Writecommunity [<community strin >]
Description:
Set or show SNMP write community strin .
[<community strin >]: New community strin . (default: Show current value).
System Trapcommunity
Syntax:

8MG – CLI UM rev. 2.2 Page 10 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
Trapcommunity [<community strin >]
Description:
Set or show SNMP trap community strin .
[<community strin >]: New community strin . (default: Show current value).
C ONSOLE C OMMANDS
Console Configuration
Syntax:
Console Confi uration
Description:
Show confi ured console password and timeout.
Console Password
Syntax:
Console Password [<password>]
Description:
Set or show the console password. The empty strin (“”) disables the password check.
[<password>]: Password strin of up to 16 characters.
Console Timeout
Syntax:
Console Timeout [<timeout>]
Description:
Set or show the console inactivity timeout in seconds. The value zero disables timeout.
[<timeout>]: Timeout value in seconds, 0, 60-10000.
Console Prompt
Syntax:
Console Prompt [<prompt_strin >]

8MG – CLI UM rev. 2.2 Page 11 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
Description:
Set or show the console prompt strin . The empty strin (“”) clears the prompt strin .
[<prompt_strin >]: Command prompt strin of up to 10 characters.
P ORT C OMMANDS
Port Configuration
Syntax:
Port Confi uration [<portlist>]
Description:
Show the confi ured and current speed, duplex mode, flow control mode and state for the port.
<portlist>: Port list (Default: All ports).
Port Mode
Syntax:
Port Mode [<portlist>] [<mode>]
Description:
Set or show the speed and duplex mode for the port.
<portlist>: Port list (Default: All ports).
<mode> : Port speed and duplex mode (Default: Show confi ured and current mode).
10hdx : 10 Mbit/s, half duplex.
10fdx : 10 Mbit/s, full duplex.
100hdx : 100 Mbit/s, half duplex.
100fdx : 100 Mbit/s, full duplex.
1000fdx: 1 Gbit/s, full duplex.
auto : Auto ne otiation of speed and duplex.
Port Flow Control
Syntax:
Port Flow Control [<portlist>] [enable|disable]
Description:

8MG – CLI UM rev. 2.2 Page 12 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
Set or show flow control mode for the port.
<portlist> : Port list (default: All ports).
[enable|disable]: Enable/disable flow control (default: Show flow control mode).
Port State
Syntax:
Port State [<portlist>] [enable/disable]
Description:
Set or show the state for the port.
<portlist> : Port list (default: All ports).
[enable|disable]: Enable or disable port state (default: Show state).
Port MaxFrame
Syntax:
Port MaxFrame [<portlist>] [<framesize>|reset]
Description:
Set or show the maximum frame size in bytes (includin FCS) for frames
received on the port. Ta ed frames are allowed to be 4 bytes lon er than the
maximum frame size. Use the reset option to return to the default settin .
[<portlist>] : Port list (default: All ports).
[<framesize>|reset]: Maximum frame size or reset to 1518 bytes (default: Show maximum frame
size).
Port Statistics
Syntax:
Port Statistics [<portlist>] [clear]
Description:
Show or clear statistics for the port.

8MG – CLI UM rev. 2.2 Page 13 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
<portlist>: Port list (default: All ports).
[clear] : Clear port statistics (default: Show statistics).
port VeriPHY
Syntax:
Port VeriPHY [<portlist>] [full|anomaly|termination]
Description:
Perform VeriPHY cable dia nostics on the specified port(s).
<portlist>: Port list (default: All ports).
[full|anomaly|termination]:
Type of dia nostics. Full comprises cable len th and full anomaly check, anomaly comprises full anomaly
check and termination comprises anomaly check without check for couplin between pairs (default: full).
MAC T ABLE C OMMANDS
MAC Configuration
Syntax:
MAC Confi uration
Description:
Show the permanently stored MAC table and the MAC a ein timer.
MAC Add
Syntax:
MAC Add <macaddress> <portlist>|none [<vid>] Description:
Add a static MAC address table entry and VLAN ID on ports.
<macaddress>: MAC address, 12-di it hex strin , optionally separated with dashes or colons (e. .
010203ABCDEF or 01-02-03-AB-CD-EF or

8MG – CLI UM rev. 2.2 Page 14 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
01:02:03:AB:CD:EF).
<portlist> : Port list. Use ”none” to specify no ports.
[<vid>] : VLAN ID, 1-4095 (default: 1).
MAC Delete
Syntax:
MAC Delete <macaddress> [<vid>]
Description:
Delete MAC address and VLAN ID.
<macaddress>: MAC address, 12-di it hex strin , optionally separated with dashes or colons (e. .
010203ABCDEF or 01-02-03-AB-CD-EF or
01:02:03:AB:CD:EF).
[<vid>] : VLAN ID (default: 1).
MAC Lookup
Syntax:
MAC Lookup <macaddress> [<vid>]
Description:
Lookup MAC address and VLAN ID.
<macaddress>: MAC address, 12-di it hex strin , optionally separated with dashes or colons (e. .
010203ABCDEF or 01-02-03-AB-CD-EF or
01:02:03:AB:CD:EF).
[<vid>] : VLAN ID, 1-4095 (default: 1).
MAC Table
Syntax:
MAC Table <vidlist>
Description:
Show MAC table for the VLAN Ids specified. Since the list can be very lon , only the first 20 entries are
shown.
<vidlist> : VLAN ID list.

8MG – CLI UM rev. 2.2 Page 15 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
MAC Flush
Syntax: MAC Flush
Description:
Removes non-static MAC address table entries.
MAC Age Time
Syntax:
MAC A etime [<a etime>]
Description:
Set or show the MAC a e timer in seconds. The value zero disables a ein .
[<a etime>]: A e timer in seconds, 0 or 10-65535 (default: Show timer)
VLAN C OMMANDS
VLAN Configuration
Syntax:
VLAN Confi uration [<portlist>]
Description:
Show the VLAN aware mode, port VLAN ID and accepted frame type for the port and the permanently
stored VLAN table.
[<portlist>]: Port list (default: All ports).
VLAN Add
Syntax:
VLAN Add <vidlist> [<portlist>]
Description:
Add VLAN entry and include ports in member set.
<vidlist> : VLAN ID list.
[<portlist>]: Port list (default: All ports).

8MG – CLI UM rev. 2.2 Page 16 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
VLAN Delete
Syntax:
VLAN Delete <vidlist>
Description:
Delete VLAN entry (all ports excluded from member set).
<vidlist> : VLAN ID list.
VLAN Lookup
Syntax:
VLAN Lookup <vidlist>
Description:
Lookup VLAN entry and show port list.
<vidlist> : VLAN ID list.
VLAN Aware
Syntax:
VLAN Aware [<portlist>] [enable|disable]
Description:
Set or show the VLAN awareness mode for the port. VLAN aware ports will strip the VLAN ta from
received frames and insert the ta in transmitted frames (except PVID). VLAN unaware ports will not strip
the ta from received frames
or insert the ta in transmitted frames.
[<portlist>]: Port list (default: All ports).
[enable|disable]: Enable/disable VLAN awareness (default: Show awareness).
VLAN PVID
Syntax:
VLAN PVID [<portlist>] [<vid>|none]
Description:
Set or show the port VLAN ID. Unta ed frames received on the port will be classified to this VLAN
ID. Frames classified to this VLAN ID will be sent unta ed on the port.
[<portlist>]: Port list (default: All ports).
[<vid>|none]: Port VLAN ID, 1-4095 (default: Show PVID).
The ’none’ option can be used for trunk links.

8MG – CLI UM rev. 2.2 Page 17 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
VLAN Frame Type
Syntax:
VLAN Frame Type [<portlist>] [all|ta ed]
Description:
Set or show the accepted frame type for the port.
[<portlist>]: Port list (default: All ports).
[all|ta ed]: Accept all or only ta ed (default: Show frame type).
A GGREGATION / TRUNKING C OMMANDS
aggregation Configuration
Syntax:
A r Confi uration
Description:
Shows the a re ation roups and the a re ation mode.
Aggregation Add
Syntax:
A r Add <portlist>
Description:
Add link a re ation roup includin ports.
<portlist>: A re ation port list.
Aggregation Delete
Syntax:

8MG – CLI UM rev. 2.2 Page 18 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
A r Delete <portlist>
Description:
Delete link a re ation roup.
<portlist>: Port list. A re ations includin any of the ports will be deleted.
Aggregation Lookup
Syntax:
A r Lookup <portlist>
Description:
Lookup and display link a re ation roup.
<portlist>: Port list. A re ations includin any of the ports will be shown.
Aggregation Mode
Syntax:
A r Mode [smac|dmac|xor]
Description:
Set or show link a re ation traffic distribution mode.
[smac|dmac|xor]: A re ation mode, SMAC, DMAC or XOR (default: Show mode).
L ACP C OMMANDS
Lacp (IEEE 802.3ad Link A re ation Protocol) provides a way to set up a re ation automatically
between switches.
LACP Configuration
Syntax:
LACP Confi uration [<portlist>]
Description:
Show the confi uration of LACP on all or some ports.

8MG – CLI UM rev. 2.2 Page 19 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
<portlist>: Port list. Default is all ports.
LACP Mode
Syntax:
LACP mode [portlist] [enable|disable]
Description:
Enable or disable LACP on all or some ports.
<portlist>: List of ports to enable or disable LACP. Default is all ports. Enable|disable: Enable or
disable LACP on the ports.
LACP Key
Syntax:
LACP key [<portlist>] [<key>|auto]
Description:
The key determines which ports potentially can a re ate to ether.
RSTP C OMMANDS
RSTP is a protocol that prevents loops in the network and dynamically reconfi ures which physical links in
a switch should forward frames.
RSTP Configuration
Syntax:
RSTP Confi uration [<portlist>]
Description:
Show the RSTP Confi uration.
RSTP Sysprio
Syntax:

8MG – CLI UM rev. 2.2 Page 20 of 67 Last Rev: 09-May-2018
Amphenol – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – www.rjswitch.com
RSTP Sysprio [<sysprio>]
Description:
Set or show the RSTP system priority.
<sysprio>: Number between 0 and 61440 in increments of 4096. This provides for
16 distinct values: 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768,
36864, 40960, 45056, 49152, 53248, 57344 and 61440.
The lower the system priority the more likely the switch is to become root in
Spannin tree.
RSTP Hellotime
Syntax:
RSTP Hellotime [<secs>]
Description:
Set or show the RSTP Hellotime value.
<secs>: Number between 1 - 10 (default is 2)
RSTP Maxage
Syntax:
RSTP Maxa e [<secs>]
Description:
Set or show the RSTP MaxA e value.
<secs>: Number between 6 - 40 (default is 20)
RSTP Fwddelay
Syntax:
RSTP Fwddelay [<secs>]
Description:
Set or show the RSTP Forward Delay value.