Amphion Create BaseTwo25 User manual

Handmade
in Finland
create
BaseTwo25 System
Reference Manual

Table of contents
Introduction
Safety warnings
Front panel controls
Back panel connections
Connectivity diagram
Technical specications
Notes
3
4
6
8
9
10
11
BaseTwo25 delivery contains:
i
1 pc Amphion BaseTwo25 2U Amplifier & Crossover
2 pc Amphion BaseTwo25 Tower
2 pc Neutrik Speakon/Speakon (NL2FX) 2-pole
speaker cable for connecting. Length 3.5 meters
1 pc BaseTwo25 Reference manual

3
Introduction
Welcome
Thank you for choosing BaseTwo25. Making correct decisions regarding the low frequencies is
fundamental and often the hardest part of sound making. BaseTwo25 delivers clear, accurate and
dependable low frequency information for making fast, well translating decisions. The system´s
extreme resolution, speed and control make it easy to pack the maximum energy into your low-end
or spot potential problems before they turn into headaches.
Anssi Hyvönen
Founder, CEO
Amphion Loudspeakers Ltd.
The System
BaseTwo25 bass extension system consists of BaseAmp1200, and a pair of double-sided bass
extenders. Each extender has a pair of back-to-back long-throw 10” woofers at the top and matching
passive radiator below. Due to the benefits of force cancellation, the extenders remain stable even
during the most demanding bass tracks.
The rack mountable 2U enclosure of BaseAmp1200 houses 2 x 700 watt amplifier and an active
crossover with selectable discrete crossover settings of 40 Hz, 60 Hz, 80 Hz, or 100 Hz. The best
crossover-setting depends on the monitor used and listening level.
BaseTwo25 transforms your 2-way monitor into a cohesive and totally integrated 3-way full-range
system. In addition to sub bass information, the system increases the power-handling and improves
midrange resolution by reducing the intermodulation distortion of the mid-woofers. The system has a
by-pass option for those moments, when the matching monitor is used for a narrower midrange view.
The by-pass can be activated via foot-switch or a push button on the front plate of the BaseAmp1200.
The selectable crossover improves integration even when monitors are not placed on top of the
extenders. Often with large format consoles, the monitors work best when placed on the meter bridge.
Using a lower crossover point helps integration even Base extenders are placed behind a console.
BaseTwo25 works with all Amphion products, as well as with other monitors that have sufficient speed
and resolution in the critical upper-bass/lower-mid frequencies.

4
Safety warnings
1. Please read and follow these instructions before using the amplifier.
2. Do not use this apparatus near water.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings.
5. Install in accordance with the manufacturer’s instructions.
6. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
7. The unit generates heat especially during prolonged operation at intensive levels. Please do not cover or place objects on top. When
rack mounting it is recommended to leave space above the unit to allow free circulation of air.
8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Any terminals marked with the preceding symbol are HAZARDOUS LIVE and any wiring connected to these terminals must
be installed by an INSTRUCTED PERSON or with ready-made leads or cords.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. DO
NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, ARE PLACED ON THE EQUIPMENT. TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT
THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN
READILY OPERABLE.

5
Service and warranty
We make sure you can enjoy your
Amphion products for a long time
Amphion Create products come with a two-year
warranty against defects in materials and our
workmanship. For warranty or out-of-warranty service,
in the first instance please contact your original
dealer and provide a copy of the original sales
receipt. If you require additional assistance, please
contact your local sales representative or distributor.
If you have difficulty making contact with either of
the above, please contact our headquarters. Please
do not return or ship any product to Amphion
Loudspeakers Ltd. nor its resellers without prior
authorisation.
For proper unpacking, installation, positioning, and
maintenance instructions, please first check the
manual thoroughly.

6
Front panel controls
2 1
483 mm / 19”
2U
89 mm
3½”
43
1
2
Power button
Power button turns on the power of the unit. Please note that hard bypass is enabled also when power is off, and
that the unit always switches to active mode after power is switched on.
Active button
Active button switches the unit between hard bypass and active mode. The BaseTwo25 is active when the light is on.
PLEASE NOTE! If power of the amplifier switches off after a few seconds when turned on, please make sure that
you push the power button all the way in.
PLEASE NOTE! BaseTwo25 improves the headroom of the monitor connected to the system, by transforming
a 2-way monitor into a cohesive 3-way full range system. In order to prevent damage to the monitors, please
exercise caution and reduce the listening volume before engaging the by-pass function.
PLEASE NOTE! Turn on power before feeding signal into the amplifier.
!
!
!

4
3
7
Level
The volume level of the low frequency extension provided by the BaseTwo25 is adjusted with the dial on the front
panel of the BaseAmp1200. The right setting depends on your speaker model sensitivity, your room low frequency
absorption, and your personal preference and application. Unlike many other bass systems, the BaseTwo25 can
be run “hot” without it losing its footing due to its precise nature. It is therefore advisable to experiment with bass
level to gain understanding on the level, which leads to good translation.
Crossover Frequency
Crossover Frequency control allows you to choose how much of the low frequency range you want the BaseTwo25
to handle. The higher the frequency, the less heavy lifting is required from your main pair of speakers. This will help
to keep the midrange clean, especially at higher SPL levels. A lower crossover frequency setting allows a subtle
add-on of the missing lowest octave(s) to your main speaker without changing the sound character you are familiar
with. As a general rule, the smaller the main speaker, the higher the crossover frequency.
Choosing the right crossover frequency can greatly help in achieving the smoothest low frequency response in
your room. In order to achieve the purest possible signal path, the variable crossover is implemented by switching
between 4 discrete filter configurations. (40 Hz, 60 Hz, 80 Hz and 100 Hz).
Front panel controls
Tip for finding a balanced setting: Use the Active Button to switch between active and bypass mode to find
a (neutral) setting where the low frequency response is extended, but not exaggerated by the Base system.
Tweak to taste as needed.
PLEASE NOTE! The effects of the crossover setting are easily seen in the travel of the mid woofer. The lower the
setting, the more bass information is fed to the mid woofer. Higher settings decrease intermodulation distortion as
the mid woofer is freed from the frequencies it struggles most to reproduce.
!

4 5 6 87
4
5
6
7
8
8
Input +4dB (L and R)
These are the balanced inputs for your stereo signal. If you are using an unbalanced source, it is recommended
to connect XLR pin 3 to pin 1.
Main out (L and R)
These are the outputs for your main power amp and speakers. If you are using an unbalanced destination,
it is recommended to leave XLR pin 3 unconnected.
Base out
Neutrik Speakon (NL2FX) 2-pole speaker outputs for the BaseTwo25 towers.
Footswitch
Possibility of using a foot-switch in addition to the by-pass button on the front of the device. This allows using
a foot pedal to activate the by-pass model in cases, where the controller is located further away from the user.
IEC power connector
Power input, auto switching in the 100-240V range, internally fused.
Back panel connections
430 mm / 17”

9
Connectivity diagram
Rear view
Right Signal
Left Signal
Main Speaker RIGHT Main Speaker LEFT
Main Amp
BaseAmp1200
BaseTwo25 RIGHT BaseTwo25 LEFT
!

10
Technical specications
BaseTwo25
BaseAmp1200
Operating principle
Drivers
Crossover
Max SPL
Frequency Response
Weight
One way with passive radiator, stereo
4 x 25 cm / 10” aluminum driver
4 x 25 cm / 10” aluminum radiator
Active 4th-order,
selectable @ 40, 60, 80, 100 Hz
127dB
20 - 100 Hz +/-3dB (low pass)
100 Hz - 200 kHz +/-3dB (high pass)
2 x 32 kg / 2 x 93 lb
Output power
THD + noise
Dynamic range
Efciency
Weight
2 x 700W @ 1% THD, 4 Ohm
@ 10W: 0,0025%
@ 100W: 0,0015%
127dB (A)
230V / 50 Hz-700W
6 kg / 13 lb

11
Notes

Amphion Loudspeakers Ltd.
Factory & Headquarters
Vitostie 1864
70800 Kuopio
Finland
Tel. [phone]
[email protected]
amphion.fi
Reference Manual
Version: 1.0 / 01.02.2021