Amroad ID5101 User manual
AMROAD ID5101
HOME STATION
~
Installation Manual
AMROAD ID5101
i
Contents
Contents.......................................... i
Package Contents ............................1
The Size of Main Unit ...................... 2
Rear Side......................................... 3
Reset Button............................................. 3
Installing Procedures ......................4
Back Plate ................................................. 4
Wire and Cable Connection ..................... 5
Install Main Unit....................................... 6
IO Application ................................ 7
PIN Color and GPIO Connectors ...............7
Lighting Control ....................................... 8
Alarm ........................................................ 9
Magnetic Switch......................................10
CO Sensor .................................................11
Emergency Button................................... 12
Gas Detector............................................ 13
Contents
AMROAD ID5101
1
Package Contents
1. Main Unit x1
2. Back Plate x1
3. Wall Mounted Screw Pack (Self Tapping
Screw TP3-L16 x4, Wall Plug x4)
4. Screw M4-L10 x2
5. Screw for Earth Wire M3-L4 x1
6. Function Key Label & IO Label
7. H-type Terminal Connector for Power
Wire x2
8. Adapter x1
9. I/O Cable x3
10. Relay x2
11. RFID Master Card x1
12. Quick Installation Guide & Quick
Operation Guide
Package Contents
AMROAD ID5101
2
The Size of Main Unit
The Size of Main Unit
AMROAD ID5101
3
Rear Side
Reset Button
1. The device will be switched to the static IP
mode and reboot itself when the user has
pressed the reset button for 3 seconds.
2. When the button has been pressed for
more than 6 seconds, the device will be
switched to the DHCP mode and reboot
itself (the users need to restore the factory
setting).
Rear Side
AMROAD ID5101
4
Installing Procedures
Back Plate
1. Make sure that is able to let the Power
Cord, Ethernet cable, and Earth Wire
pass through the hole. The bottom of
standard wall box is height 134cm from
the floor.
2. Connect the ground wire to the Back
Plate.
3. Use Wall Mounted Screw Pack to fix
Back Plate on the wall.
Installing Procedures
Back
Plate
AMROAD ID5101
5
Wire and Cable Connection
1. Connect Ethernet Cable. (RJ-45
Connector).
2. Connect the DC power cord of DP100 to
H-type power connector. Please be
careful to connect power cord DC +12V
from wall.
3. There are 8 input ports and 5 output
ports on the rear side. More information
please follows P.3, and connection
reference IO Application P.7-13.
Installing Procedures
W
ire and Cable Connection
AMROAD ID5101
6
Install Main Unit
1. After connecting the wires and cables
properly, then screw the 2 screws
(M4-L10) that come with the package
into the front panel.
2. Please double check all the installation
procedures again, then you may power
on the general power switch to start
the configuration procedures.
Installing Procedures
Install Main Unit
AMROAD ID5101
7
IO Application
PIN Color and GPIO Connectors
Before begin to connect other devices to the
ID5101, the I/O cables and their colors for GPIO
connectors are illustrated as figure above.
IO Application
PIN Color and GPIO Connectors
AMROAD ID5101
8
Lighting Control
The illustrations show how to use first GPIO
connector and wire to connect Adapter and
two Relay Boards for Lighting Control.
IO Application
Lighting Control
AMROAD ID5101
9
Alarm
The illustrations show you how to use first
GPIO connector and wire to connect AC Power,
Adapter and Relay Board for ALARM system.
IO Application
Alarm
AMROAD ID5101
10
Magnetic Switch
Both diagram and photo show how to use
second row of the GPIO connector to connect
with Magnetic Switches, and you can connect
up to four magnetic switches accordingly based
on the diagram or photo.
IO Application
Magnetic Switch
AMROAD ID5101
11
CO Sensor
Both diagram and photo show how to use 3rd
GPIO connector to connect CO Sensor, and
connect CO Sensor based on the diagram or
photo.
IO Application
CO Sensor
AMROAD ID5101
12
Emergency Button
Both diagram and photo show how to use 3rd
GPIO connector to connect Emergency Button.
The purple wire on the third-row GPIO
connector is used to connect the NO wire.
IO Application
Emergency Button
AMROAD ID5101
13
Gas Detector
Both diagram and photo show how to use 3rd
GPIO connector to connect Gas Detector. The
gray wire on the third-row GPIO connector is
used to connect the NO wire. Besides, Gas
Detector needs to connect an external AC
Power.
IO Application
Gas Detector
Other manuals for ID5101
3
Table of contents
