AMSAN AM-PSPL6 User manual

PLEASE READ THE PRODUCT MANUAL ENTIRELY BEFORE INSTALLING OR
OPERATING THE LIFT.

Single Post Lift AM-PSPL6
2
IMPORTANT INFORMATION
•The shipment should be thoroughly inspected as soon as it is received. Any freight
damage or missing items must be noted on the freight bill before signing and reported
to the freight carrier with a freight claim established. Buyer should claim the
compensation from the freight carrier if any damage happens to the equipment during
shipping. Please refer to our website for detailed shipping policies and procedures.
•Make sure you have additional help or heavy-duty lifting equipment when unloading and
assembling the lift.
•Read and understand this installation and operation manual entirety before attempting
to install or operate the lift. Keep this manual near the product for future references.
Make sure all operators read this manual.
•The lift should only be operated by authorized personnel. Keep children and untrained
personnel away from the lift.
•Do not make any modifications to the Lift; this voids the warranty and increases the
chances of injury or property damage. •
•Do not use the lift while tired or under the influence of drugs, alcohol, or medication
•Manufacturer or distributor assumes no responsibility for loss or damage of any kind,
expressed or implied, resulting from improper installation or use of this lift. Always use
professional installation companies.
•All persons using the equipment must be responsible, qualified, and carefully follow the
operation and safety guidelines contained in this manual.
•A level floor is required for proper lift installation and operation.
•The lift must be placed on flat and hard ground, which is made of cement or bricks, with
the load at the position of vertical post of 3t/m2.
•DO NOT install this lift on an upper floor without written authorization from your building
engineer. Should only be installed on a ground floor without a basement.
•DO NOT attempt to lift only part of a vehicle. This lift is intended to raise the entire body
of a vehicle only. This will bend the arms and void the warranty.
•NEVER lift any persons or vehicles containing persons. This lift is designed to lift empty
vehicles only.
•Any vehicle whose weight is above 6,000lb is not allowed to be raised on this machine.
•All wiring must be performed by a licensed, certified Electrician.
•Do not perform any maintenance until main electrical power has been disconnected
from the lift and cannot be re-energized until all procedures are complete.
•All information in this manual is believed to be correct at time of publication. The design,
material and specifications are subject to change without notice.

Single Post Lift AM-PSPL6
3
TABLE OF CONTENTS
Contents
TABLE OF CONTENTS................................................................................................................................. 3
SAFETY INSTRUCTIONS AND CAUTIONS........................................................................................................... 4
CAUTION SIGNS....................................................................................................................................... 4
LIFTING CAPACITY ................................................................................................................................... 5
SAFETY CHECK POINTS FOR OPERATION ..................................................................................................... 5
LIFT COMPONENTS....................................................................................................................................... 7
LIFT DIMENSIOINS ....................................................................................................................................... 8
TECHANICAL SPECIFICATIONS....................................................................................................................... 9
INSTALLATION........................................................................................................................................... 10
SPACE REQUIREMENTS ........................................................................................................................... 10
FOUNDATION REQUIREMENTS .................................................................................................................. 10
TOOLS RECOMMENDED ........................................................................................................................... 10
INSTALLATION INSTRUCTIONS ................................................................................................................. 11
OPERATION........................................................................................................................................... 12
MAINTENANCE ....................................................................................................................................... 16
DAILY INSPECTION................................................................................................................................. 16
MONTHLY INSPECTION............................................................................................................................ 17
EVERY 6 MONTH INSPECTION .................................................................................................................. 17
TROUBLE SHOOTING .................................................................................................................................. 18
HYDRAULIC DRAWING................................................................................................................................ 20
CIRCUIT DIAGRAM .................................................................................................................................... 21
EXPLODED DRAWING.................................................................................................................................. 22
MAINTENANCE LOG .................................................................................................................................... 24

Single Post Lift AM-PSPL6
4
SAFETY INSTRUCTIONS AND CAUTIONS
CAUTION SIGNS
Danger! Pay special attention to this symbol as it
means unsafe or hazards practices which can lead
to severe personal injury or death or damage to the
lift or property.
Caution! Read and follow the instructions next to
this symbol to avoid big casualty and heavy
damage to the lift.
Attention! The section besides this signal lists the
notice points and security requirements during
the process of normally using, maintenance and
care of the lift.

Single Post Lift AM-PSPL6
5
LIFTING CAPACITY
Rated Load
AM-PSPL6
6,000LB
SAFETY CHECK POINTS FOR OPERATION
•Operators should read the manual carefully to avoid accidents.
•Operators should be familiar with all functions and operating methods
of the lift.
•Check before operating and regular check must be carried out too.
•If there is any abnormal sound during rising and lowering, stop to use
the lift.
•Never use the lift to raise the vehicle whose weight is above 6,000lb.
•Read the operating manual.
•Lift operation by authorized personnel over 18 years only.
•Always keep the lift and lift area clean and free of tools, parts, debris
etc.
•Once the disk adapters contact the lift points, check arm restraints for
engagement.
•After raising the vehicle briefly, stop and check the disk adapters for
secure contact.
•Always lift the vehicle using all four adapters.
•Make sure the vehicle doors are closed during raising and lowering

Single Post Lift AM-PSPL6
6
cycles.
•Closely watch the vehicle and the lift during raising and lowering cycles.
•Do not allow anyone to stay in lift area during raising and lowering
cycles.
•Do not allow anyone on lift or inside raised vehicle.
•Only use the lift for its intended purpose.
•Comply with the applicable accident prevention regulations.
•Do not overload the lift. The rated load capacity is indicated on the lift
nameplate.
•Only use the vehicle manufacturer’s recommended lift points.
•After positioning the vehicle apply the parking brake.
•Use caution when removing or installing heavy components (center-of-
gravity
•displacement).
•The main switch serves as emergency switch. In case of emergency
turn to OFF
•position.
•Protect all parts of the electrical equipment from humidity and moisture.
•Protect the lift against unauthorized usage by padlocking the main
switch.
SAFETY CHECK POINTS FOR SERVICING
•Maintenance or repair work by authorized service personnel only.
•Turn off and padlock the main switch before doing any maintenance, or
repair work.
•Work on pulse generators or proximity switches by authorized service
personnel only.

Single Post Lift AM-PSPL6
7
•Work on the electrical equipment by certified electricians only.
•Ensure that ecologically harmful substances are disposed of only in
accordance with
•the appropriate regulations.
•Do not use high pressure/steam jet cleaners orcaustic cleaning agents.
•Do not replace or override the safety devices.
LIFT COMPONENTS

Single Post Lift AM-PSPL6
8
LIFT DIMENSIOINS

Single Post Lift AM-PSPL6
9
TECHANICAL SPECIFICATIONS
Overall Height
2522MM (99.29")
Maximum Lifting Height
1800MM (70.87")
Adjusting Range of Arm
R500 - 685mm (19.69”- 26.97”) and R630 -
945mm (24.80” –37.20”)
Overall Length
2300MM (90.55")
Power Unit
110 VAC / 1PH / 60HZ
Noise Level
≤70dB(A)
Overall Width
1200MM (47.24”)
The design, material and specifications are subject to change without notice.

Single Post Lift AM-PSPL6
10
INSTALLATION
SPACE REQUIREMENTS
•The area where the lift will be located should be free of overhead obstructions
such as heaters, building supports, electrical wires and so on. Also make there
is enough clearance around the lift for driving vehicles getting on or off the lift.
Please refer below for exact measurements.
•There should be ＞about 1,000mm space around the vehicle lifted, and the net
height indoor is about 3600mm.
FOUNDATION REQUIREMENTS
•Visually inspect the site where the lift is to be installed and check for cracked
or defective concrete
•DO NOT install or use this lift on expansion seams or on cracked or defective
concrete.
•DO NOT install or use this lift on any asphalt surface or any surface other than
concrete.
•Lift is designed for INDOOR INSTALLATION ONLY.
•This lift must be installed on a solid level concrete floor with no more than 3-
degrees of slope.
•Lift buyers are responsible for any special regional structural and/or seismic
anchoring requirements specified by any other agencies and/or codes such as
the Uniform Building Code (UBC) and/or International Building Code (IBC).
•All models MUST be installed on 3000 PSI concrete and have a minimum of 12”
thickness with steel or fiber mesh. New concrete must be adequately cured by
at least 30 days minimum.
TOOLS RECOMMENDED
⚫Chalk Line
⚫
⚫4 Foot Level
⚫Set of Metric Wrenches/Sockets
⚫
⚫Flat Screwdriver
⚫Adjustable Wrench
⚫
⚫Hex-Key / Allen Wrench Set
⚫Locking Pliers
⚫
⚫Needle Nose Pliers
⚫Tape Measure
⚫
⚫Rotary Hammer Drill
⚫Step Ladder
⚫
⚫3/4" Masonry Bit
⚫Hammer
⚫
⚫3 Gallons of Hydraulic Oil*
⚫Crow Bar
⚫Forklift
⚫
*Recommended Oil: ISO 32, ISO 46 Hydraulic Oil or Dexron III ATF

Single Post Lift AM-PSPL6
11
INSTALLATION INSTRUCTIONS
ONLY TRAINED INSTALLERS SHOULD PERFORM LIFT INSTALLATION
WORK.
90% components were pre-assembled before shipment and packed with blister
packing in steel frame. Arms, adapters, and rubber pads were put in the lift. Power unit
was packed in carton box separately, power unit stand was packed and fixed on above
the lifts.
Because of the limitation of transportation, lift shall be disassembled to pack. The
users should assemble the lift according to the following figure:
Assemble movable single column lift Overall assembly as follows:

Single Post Lift AM-PSPL6
12
OPERATION
Please read the operation manual carefully before operating the lift.
Only authorized technician should be operating the lift.
•Clear the area immediately, if Vehicle on lift suspected of falling.
•Do not operate a lift that is damaged or in need of repair.
Operation Rules for mechanism System
•The movable single column lift is provided with separate traveling mechanism.
Shake the hauling handle of the steering rear wheel forwards and backwards to
make the vertical column off the ground, then you can push or pull the lift. On
arriving the working site, press the valve handle to retract the wheel, then the
vertical column lands on the ground steadily.
•The lift must only be pushed into the vehicle if in line with it. Insert the pallet
under the vehicle beam and the pallet must be in line with the beam.
•Retract the rear wheel of vertical post to land the vertical post steadily before
the lift lifts load, and make sure there is no foreign article such as hand tools,
bolts, screw caps, small stones. No lifting during moving!
Operating Steps for Electrical Control System
•New machine is operated for commissioning without load before its first use.
The electrical box is provided with “0-1” main power switch, which should be
turned off after the machine use finished.
Operation Flow:
•Vehicle stops in the service position with engine off
•Turn the handle for hydraulic movable wheel to lift the vertical post base a bit
•Push the lift into the underside of vehicle
•Make sure there is no foreign articles under the base and the ground is level
•Grasp the valve handle to make the base lowered to ground
•Align 4 pallets on the lifting arm respectively to the supported positions on the
vehicle underside
•Press the “green” button to raise the vehicle by 10～15 centimeters
•Stop the vehicle raising and check for safe and secure four high points of the
pallet.
•Check if the main lifting arm touches the vehicle bottom plate, which should
not occur during normal lifting.

Single Post Lift AM-PSPL6
13
•Pull the safety unlock handle to make the fliting platform unlocked.
•To adjust lifting pad, turn it anticlockwise to make it rise (adjustment distance
of 100mm)
•Press the “green” button again and pay attention to lifting arm and the vehicle
lifted until lifting is safe and reliable.
•Raise the lift to the required height, then lower it to the lock position
•After the repair of vehicle is finished, raise the lift about 2-3cm, pull the release
cable on the column, then push the lowering handle on power unit to lower the
lift.
•Turn the handle of hydraulic pump and the lift is off the ground, pull out the
lift. 16)Drive the vehicle away.

Single Post Lift AM-PSPL6
14
Movable lift pushed into the underside of the vehicle
Vehicle driving onto the lift
Use lifting arm
Movable Lift
•According to the position under the vehicle chassis where the lifting arm is
located, the supporting arm on the lifting arm (close to the vertical post) may
be pushed and pulled up and down or to left and right:
•The supporting arm in the front of lifting arm may be turned or pushed or
pulled inward or outward, or to left and right.
•The height of pallet can be adjusted by turning it clockwise or anticlockwise.

Single Post Lift AM-PSPL6
15
Control unit
Release handle

Single Post Lift AM-PSPL6
16
MAINTENANCE
DAILY INSPECTION
Item
Maintenance Contents
Solution
1
Check if there are any damages on
the rubber pad on four arms.
Replace rubber pads.
2
Check if there is any problem on the
bolts, nuts, and cotter pin of all
spare parts. If loose or damaged
Check and tighten all the loose nuts
and bolts, clean and if needed
replace with new parts.
3
Check if the pivot chain sheave and
chain are in their position.
Add lubrication or adjust again.
4
Check Switches and wiring for
damages
Replace damaged switches and
wiring.
5
Check the connection of oil pipeline
for leakage
Find the leakage and tighten the
loose nuts and clean oil stains.
6
Check if it is time to add or change
hydraulic oil.
Add or change the oil.
7
Check for frayed cables/ cable
connections
If need replace the damaged cable
8
Check anchors, nuts, and bolt
Tighten them

Single Post Lift AM-PSPL6
17
MONTHLY INSPECTION
Item
Maintenance Contents
Solution
1
Inspect rubber pads
Replace rubber pads if required
2
Check hydraulic hoses and line for
possible lease or damage
Tighten the fittings and if needed
replace the hose
3
Check if the pivot chain sheave and
chain are in their position.
Add lubrication or adjust again.
4
Check if it is time to add or change
hydraulic oil.
Add or change the oil.
EVERY 6 MONTH INSPECTION
Item
Maintenance Contents
Solution
1
Lubricate rollers and pins
Use gear oil or equivalent
2
Check hydraulic hoses and line for
possible leak or damage
Tighten the fittings and if
needed replace the hose
3
Check if the pivot chain sheave and
chain are in their position.
Add lubrication or adjust again.
4
Check for Cable tensions
Tighten the cable nuts

Single Post Lift AM-PSPL6
18
TROUBLE SHOOTING
Problem
Reason
Solution
Motor does not
work
• Incorrect Voltage to motor
• Motor burned out
• Fuses are blown
• Start Button damaged
• Limit or Micro switch
burned out
• Check the power fuse and
reset breaker
• See if power unit wired
correctly
• Avoid extension cords
• Double check the installation
manual if any step got missed
Lift does not
raise
• Incorrect voltage to power
unit
• Internal leak to cylinder
and lowering valve
• Motor damaged
• Oil has air in it
• Dirty oil
• Hydraulic leak
• Load exceeds the
capacity of the lift
• Replace dirty oil and use
Dexron ATF
• Check oil level if low top it up to
the correct level
• See installation manual for
bleed cylinders
• Double check the voltage and
wiring
• Replace Damaged motor
• Thorough inspect lift for
leakage and fix them
• Double check the load
Capacity and make sure it’s
below the rated capacity for the
vehicle lift
Lift does not
stay up
• Oil has air in it
• Internal leak to cylinder
and lowering valve
• Motor damaged
• Fitting leaks
• Check oil level if low top it up to
the correct level
• See installation manual for
bleed cylinders
• Replace Damaged motor
Loud noise
coming from
the Lift while
raising/loweri
ng the load
• The sliding and rotational
part missing lubrication
• Damaged Sliders or
Sliders missing lubrication
• Add lubrication to sliders and
other rotational parts
• Replace Sliders
Power Unit
make noise
and does not
work.
• Capacitor is damaged.
• The voltage is too low.
• The equipment is used
overload.
• Replace the Capacitor
• Have an electrician check the
low voltage issue
Motor has
insufficient
pressure to
raise the lift
• Hydraulic leak
• Load exceeds the
capacity of the lift
• Low Fluid level
• Remove the leak
• Double check the load
Capacity and make sure its
below the rated capacity for the

Single Post Lift AM-PSPL6
19
vehicle lift
• Fill the reservoir with
manufacturing recommended
oil
When lift is
rising the speed
is slow and
high.
• There is not enough
hydraulic oil in the power
unit reservoir
• Hydraulic leakage
• Add hydraulic oil
• Fix or replace the leaky hoses
Lift Cannot be
lowered
• Safety Cable is
damaged
• Release valve is
damaged
• Oil pipeline has jammed
• See installation manual for
bleed cylinders
• Readjust the cable

Single Post Lift AM-PSPL6
20
HYDRAULIC DRAWING
No
Name
No
Name
No
Name
1
Tank
5
Start buffer valve
9
Relief valve
2
Filter
6
One-way valve
10
Anti-explosion valve
3
Oil pump
7
Release valve
11
4
Motor
8
Return oil throttle valve