Amtech S8187 User manual

HIGH PERFORMANCE USB RECHARGEABLE REAR BIKE LIGHT
Stock Code: S8187
LIGHT OPERATION:
1. Press the on/off power button to switch the light on
and select the constant mode.
2. The 4 static light modes can now be selected by
pressing the on/off power button in sequence:
low - standard - high - overdrive.
3. To activate the flashing modes, double press the
button. The 4 flashing modes can now be selected by
pressing the power button in sequence:
low flashing - standard flashing - high flashing - strobe.
4. Press and hold the power button for approx. 1 - 2 secs
to turn the light off.
HOW TO MOUNT THE REAR LIGHT:
The rear light can be mounted using either the standard
easy mount bracket, the saddle rail mounting bracket or
the belt clip bracket.
USING STANDARD EASY MOUNT BRACKET:
Position the bracket on the seat post and wrap the strap around the post, stretching the strap slightly to secure. Make
sure the strap is securely located on the hook. Slide the light onto the bracket until it clicks into place. The light can be
mounted either vertically or horizontally. Press and hold down the release lever on the bracket to remove the light. When
mounted on the seat post, adjust the angle of the light so it does not point directly in the view of other road users.
USING THE SADDLE RAIL BRACKET:
Loosen the screws in the saddle bracket using a hex. key and clamp the bracket on the saddle rail. Align the screw holes and
tighten the bracket. Slide the light forward onto the bracket until it clicks into place. Press down the release lever on the bracket
to remove the light. Adjust the direction of the light as required.
USING THE BELT CLIP BRACKET:
Slide the light onto the belt clip bracket until it clicks into place. Press down the release lever to remove the light.
IMPORTANT - BEAM ADJUSTMENT:
Adjust the beam to prevent it from blinding oncoming vehicles on the public road.
HOW TO CHARGE THE BATTERY:
The micro USB charging socket is located under the rubber cover at the back of the light. Plug the micro USB plug end into the
USB charging socket and plug the other end of the USB cable into a computer USB port or suitable USB charger. If using a USB
mains charger please check the voltage is not greater than 5V and the output is not greater than 1.0A. When charging is complete
replace the rubber cover securely. With the micro USB cable connected, the battery indicator LED will be blue. The blue LED will
slowly pulse when the battery is being charged and will change to constant blue when fully charged. When the battery is low
the blue LED will flash. Only use the micro USB cable supplied with the light.
Please note: If the light is not going to be used for a long period of time, it is important to recharge every three months before
storing in order to maintain the life of the battery.
REAR LIGHT LUMEN OUPUT AND APPROX. RUN TIMES:
Low: 15 lumens - up to 7.5 hours
Standard: 30 lumens - up to 3.5 hours
High: 45 lumens - up to 2 hours
Overdrive: 100 lumens - up to 1 hour
Low flashing: 10 lumens - up to 20 hours
Standard flashing: 50 lumens - up to 4 hours
High flashing: 100 lumens - up to 2 hours
Strobe flashing: 20 lumens - up to 10 hours
1.
SPECIFICATIONS:
100 Lumen high brightness COB RED LED
Rechargeable Lithium-polymer battery (3.7 800 mAh)
Low battery, charging and fully charged indicator
Automatic fully charged cut-off system
Aluminium heat sink casing
8 modes: • Low • Standard • High • Over drive • 10% flashing
• 50% flashing • 100% flashing • Strobe
Standard easy mount bracket
(suitable for diameters 20-52mm)
Saddle rail mounting bracket
Belt clip
Micro USB charging cable