AMX Epica DGX 16 User manual

Instruction Manual
AutoPatch Matrix Switchers
Epica DGX 16
Epica DGX 32
Distribution Matrix
REV B1: 1/25/2011

AMX Limited Warranty and Disclaimer
This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized
Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from
the date of purchase, with the following exceptions:
• LCD Panels are warranted for three (3) years, except for the display and touch overlay components are
warranted for a period of one (1) year.
• Disk drive mechanisms, pan/tilt heads, power supplies are warranted for a period of one (1) year.
• AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting
products, as long as the AMX lighting products are under warranty. AMX also guarantees the control of
dimmable loads that are properly connected to our lighting products. The dimming performance or quality
there of is not guaranteed, due to the random combinations of dimmers, lamps and ballasts or transformers.
• AMX software is warranted for a period of ninety (90) days.
• Batteries and incandescent lamps are not covered under the warranty.
• AMX AutoPatch Epica, Modula, Modula Series 4, Modula Cat Pro Series and 8Y-3000 product models will be
free of defects in materials and manufacture at the time of sale and will remain in good working order for a
period of three (3) years following the date of the original sales invoice from AMX. The three-year warranty
period will automatically be extended to the life of the product (Limited Lifetime Warranty). The life of the
product extends until five (5) years after AMX ceases manufacturing the product model. The Limited Lifetime
Warranty applies to products in their original installation only. If a product is moved to a different installation,
the Limited Lifetime Warranty will no longer apply, and the product warranty will instead be the three (3) year
Limited Warranty.
REV G, Page 1 of 10, Effective Date 1-01-10
Note: The complete Warranty is at www.amx.com.

Contents
i
Epica DGX 16 and Epica DGX 32 Instruction Manual
Contents
ESD Warning .......................................................................................................1
Important Safety Information and Instructions....................................................2
Information et directives de sécurité importantes...............................................3
Notices ................................................................................................................4
Overview and General Specifications ..................................................................7
Applicability Notice ................................................................................................................. 7
Product Notes ......................................................................................................................... 8
Front View............................................................................................................................. 10
Rear View .............................................................................................................................. 10
Epica DGX 16 General Specifications .................................................................................... 14
Epica DGX 32 General Specifications .................................................................................... 14
Configuration Information and Control Options.................................................................... 15
System Diagnostic Options ................................................................................................... 16
Installation and Setup........................................................................................17
UL Safety Certifications, Notices, and Recommendations for Laser Products ....................... 17
Site Recommendations .......................................................................................................... 18
General Hazard Precautions .................................................................................................. 18
Unpacking.............................................................................................................................. 19
System Setup Options ........................................................................................................... 20
Rack Installation and System Setup ....................................................................................... 20
Linking Enclosures ................................................................................................................. 24
Attaching External Controllers .............................................................................................. 29
Attaching Input and Output Cables....................................................................................... 35
Applying Power and Startup ................................................................................................. 36
Redundant Power Supply (RPS) ............................................................................................. 39
Executing a Test Switch.........................................................................................................40
Technical Support.................................................................................................................. 42
Establishing an NXB-AP-1000 Connection (TCP/IP Port) ....................................................... 42
Epica DGX SC Optical Boards ...........................................................................47
Specifications Epica DGX SC Optical Boards......................................................................... 48
System Setup with DGX Modules.......................................................................................... 49
Safety Recommendations for Laser Products ........................................................................ 50
Attaching Cables ................................................................................................................... 50
Epica DGX DVI Boards ......................................................................................53
Specifications Epica DGX DVI................................................................................................ 54
Attaching Cables ................................................................................................................... 55

Contents
ii Epica DGX 16 and Epica DGX 32 Instruction Manual
Control Panel Operation................................................................................... 57
Overview ...............................................................................................................................57
Executing Switches ................................................................................................................ 61
Changing the Virtual Matrix ..................................................................................................62
Disconnecting Switches .........................................................................................................63
Verifying Signal Status...........................................................................................................64
Defining and Executing Global Presets ................................................................................. 65
Executing Local Presets .........................................................................................................67
Adjusting Audio.....................................................................................................................68
Locking and Unlocking...........................................................................................................72
Setup Options .......................................................................................................................73
System Error Codes and Troubleshooting .............................................................................77
NXB-AP-1000 Interface – Initial Setup by Network Admin............................... 79
Overview ...............................................................................................................................79
Determining IP Address for NXB-AP-1000 Interface .............................................................80
Opening the NXB-AP-1000 Interface.....................................................................................81
Navigating the NXB-AP-1000 Interface .................................................................................82
Getting a DHCP IP Address ...................................................................................................82
Setting a Static IP Address .................................................................................................... 83
Configuring a Connection to a NetLinx Master .....................................................................83
Handling Security Issues ........................................................................................................85
Executing a Test Switch with the XBar Controller .................................................................87
Customizing the XBar Controller ........................................................................................... 88
Executing and Disconnecting Switches..................................................................................89
Editing the Clock Manager Settings ......................................................................................89
DoD Security Mode ...............................................................................................................91
ICSP Support .........................................................................................................................93
NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32 .......................... 95
XBar Controller Overview......................................................................................................95
Executing and Disconnecting Switches with the XBar ...........................................................95
NXB-AP-1000 Interface – Additional Info for Network Admin ......................... 99
Upgrading Firmware..............................................................................................................99
Embedding the XBar Applet ...............................................................................................100
Changing the Proxy Setting.................................................................................................101
Epica DGX 16/32 NetLinx Programming ........................................................ 105
Overview .............................................................................................................................105
Device Numbering...............................................................................................................105
Device Ports ........................................................................................................................105
SEND_COMMANDs.............................................................................................................106

Contents
iii
Epica DGX 16 and Epica DGX 32 Instruction Manual
Appendix A – EDID Programmer.....................................................................109
EDID Overview .................................................................................................................... 109
Determining the Need for EDID Programming ................................................................... 110
Installing the EDID Programmer.......................................................................................... 110
Reading and Saving EDID Data from a Destination Device ................................................. 111
Writing EDID Data to Epica DGX 16 or 32 DVI Input Connector......................................... 112
Appendix B – Managing Configuration Files ...................................................115
Overview ............................................................................................................................. 116
Installing and Launching XNConnect ................................................................................... 117
Discovering a System .......................................................................................................... 118
Opening an .xcl Configuration File ...................................................................................... 119
Navigating the Interface...................................................................................................... 120
Modifying an .xcl Configuration File.................................................................................... 121
Loading an .xcl Configuration File ....................................................................................... 124
Device Discovery Support ................................................................................................... 125
Appendix C – APDiagnostics ...........................................................................127
Overview ............................................................................................................................. 127
System Requirements .......................................................................................................... 127
Installing APDiagnostics ...................................................................................................... 127
Modes ................................................................................................................................. 129
Main Screen and Menus ...................................................................................................... 129
Communications .................................................................................................................. 138
Appendix D – Programmer’s Interface for System Diagnostics .......................139
System Component Information.......................................................................................... 139
Using BCS to Access System Diagnostic Information .......................................................... 140
Splash Screen Examples ...................................................................................................... 141
Appendix E – Board Replacement...................................................................145
Procedure Overview............................................................................................................ 145
Safety Recommendations for Laser Products ...................................................................... 146
Replacing or Adding a Board .............................................................................................. 146
Board Troubleshooting........................................................................................................ 149

Contents
iv Epica DGX 16 and Epica DGX 32 Instruction Manual

ESD Warning
1
Epica DGX 16 and Epica DGX 32 Instruction Manual
ESD Warning
To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are
properly grounded before touching any internal materials.
When working with any equipment manufactured with electronic devices, proper ESD
grounding procedures must be followed to make sure people, products, and tools are as free of
static charges as possible. Grounding straps, conductive smocks, and conductive work mats
are specifically designed for this purpose.
Anyone performing field maintenance on AMX AutoPatch equipment should use an
appropriate ESD field service kit complete with at least a dissipative work mat with a ground
cord and a UL listed adjustable wrist strap with another ground cord. These items should not
be manufactured locally, since they are generally composed of highly resistive conductive
materials to safely drain static charges, without increasing an electrocution risk in the event of
an accident. ESD protective equipment can be obtained from 3M™, Desco®, Richmond
Technology®, Plastic Systems®, and other such vendors.

Important Safety Information and Instructions
2Epica DGX 16 and Epica DGX 32 Instruction Manual
Important Safety Information and Instructions
When using and installing your AMX AutoPatch product, adhere to the following basic safety
precautions. For more information about operating, installing, or servicing your AMX AutoPatch
product, see your product documentation.
 Read and understand all instructions before using and installing AMX AutoPatch
products.
 Use the correct voltage range for your AMX AutoPatch product.
 There are no user serviceable parts inside an AMX AutoPatch product; service
should only be done by qualified personnel.
 If you see smoke or smell a strange odor coming from your AMX AutoPatch product,
turn it off immediately and call technical support.
 For products with multiple power supplies in each unit, make sure all power supplies
are turned on simultaneously.
 Use surge protectors and/or AC line conditioners when powering AMX AutoPatch
products.
 Only use a fuse(s) with the correct fuse rating in your enclosure.
 Make sure the power outlet is close to the product and easily accessible.
 Make sure the product is on or attached to a stable surface.
 Turn off equipment before linking pieces together, unless otherwise specified in that
product’s documentation.
 For safety and signal integrity, use a grounded external power source and a grounded
power connector.
 Turn off and unplug an enclosure before adding or removing boards, unless
otherwise specified in that product’s documentation.
 To avoid shock or potential ESD (Electrostatic Discharge) damage to equipment,
make sure you are properly grounded before touching components inside an AMX
AutoPatch product.

Information et directives de sécurité importantes
3
Epica DGX 16 and Epica DGX 32 Instruction Manual
Information et directives de sécurité
importantes
Veuillez vous conformer aux directives de sécurité ci-dessous lorsque vous installez et utilisez
votre appareil AMX AutoPatch. Pour de plus amples renseignements au sujet de l’installation,
du fonctionnement ou de la réparation de votre appareil AMX AutoPatch, veuillez consulter la
documentation accompagnant l’appareil.
 Lisez attentivement toutes les directives avant d’installer et d’utiliser les appareils
AMX AutoPatch.
 Le voltage doit être approprié à l’appareil AMX AutoPatch.
 Les appareils AMX AutoPatch ne contiennent aucune pièce réparable par l’usager; la
réparation ne doit être effectuée que par du personnel qualifié.
 Si de la fumée ou une odeur étrange se dégagent d’un appareil AMX AutoPatch,
fermez-le immédiatement et appelez le Service de soutien technique.
 Veillez à ce que tous les blocs d’alimentation des appareils dotés de blocs
d’alimentation multiples dans chaque unité soient allumés simultanément.
 Servez-vous de protecteurs de surtension ou de conditionneurs de lignes à courant
alternatif lorsque vous mettez les appareils AMX AutoPatch sous tension.
 Placez uniquement des fusibles de calibre exact dans les boîtiers.
 Veillez à ce que la prise de courant soit proche de l’appareil et facile d’accès.
 Veillez à ce que votre appareil AMX AutoPatch soit installé sur une surface stable ou
qu’il
y soit fermement maintenu.
 Fermez toutes les composantes de l’équipement avant de relier des pièces, à moins
d’indication contraire fournie dans la documentation de l’appareil.
 Par mesure de sécurité et pour la qualité des signaux, servez-vous d’une source
d’alimentation externe mise à la terre et d’un connect d’alimentation mis à la terre.
 Fermez et débranchez le boîtier avant d’ajouter ou d’enlever des plaquettes, à moins
d’indication contraire fournie dans la documentation du appareil.
 Pour éviter les chocs ou les dommages éventuels causés à l’équipement par une
décharge électrostatique, veillez à ce le dispositif oit bien relié à la terre avant de
toucher les composantes se trouvant à l’intérieur d’un appareil AMX AutoPatch.

Notices
4Epica DGX 16 and Epica DGX 32 Instruction Manual
Notices
Copyright Notice
AMX©2011 (Rev B1), all rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of AMX. Copyright
protection claimed extends to AMX hardware and software and includes all forms and matters
copyrightable material and information now allowed by statutory or judicial law or herein after
granted, including without limitation, material generated from the software programs which are
displayed on the screen such as icons, screen display looks, etc. Reproduction or disassembly
of embodied computer programs or algorithms is expressly prohibited.
Liability Notice
No patent liability is assumed with respect to the use of information contained herein.
While every precaution has been taken in the preparation of this publication, AMX assumes no
responsibility for error or omissions. No liability is assumed for damages resulting from the use
of the information contained herein.
Further, this publication and features described herein are subject to change without notice.
US FCC Notice
The United States Federal Communications Commission (in 47CFR 15.838) has specified that
the following notice be brought to the attention of the users of this product.
Federal Communication Commission Radio Frequency Interference Statement:
“This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
If necessary, the user should consult the dealer or an experienced radio/television technician
for additional suggestions. The user may find the booklet, How to Identify and Resolve Radio-
TV Interference Problems, prepared by the Federal Communications Commission to be
helpful.”
This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402,
Stock N. 004-000-00345-4.
Use shielded cables. To comply with FCC Class A requirement, all external data interface
cables and adapters must be shielded.

Notices
5
Epica DGX 16 and Epica DGX 32 Instruction Manual
Trademark Notices
AMX®, AutoPatch®, NetLinx®, and SmartScale™ are trademarks of AMX.
Windows is a registered trademark of Microsoft Corporation in the United States and other
countries.
HyperTerminal®is a copyright product of Hilgraeve Inc.
3M®, Desco®, Richmond Technology®, and Plastic Systems®are registered trademarks.
Neuron®and LonTalk®are registered trademarks of Echelon.
TosLink® is a registered trademark of the Toshiba Corporation.
Ethernet®is a registered trademark of the Xerox Corporation.
ENERGY STAR®is a registered trademark of the U.S. Department of Energy and the
U.S. Environmental Protection Agency.
Other products mentioned herein may be the trademarks of their respective owners.
Lithium Batteries Notice
Switzerland requires the following notice for products equipped with lithium batteries. This
notice is not applicable for all AMX equipment.
Upon shipment of products to Switzerland, the requirements of the most up-to-date Swiss
Ordinance Annex 2.15 of SR 814.81 will be met including provision of the necessary markings,
documents, and annual reports relative to the disposal of the batteries to the Swiss Authorities.
Warnings and Cautions
This manual uses the following conventions and icons to draw attention to actions or conditions
that could potentially cause problems with equipment or lead to personal risk.
ESD Warning: The icon to the left indicates text regarding potential danger associated with the
discharge of static electricity from an outside source (such as human hands) into an integrated
circuit, often resulting in damage to the circuit.
Warning: The icon to the left indicates text that warns readers against actions or conditions that
could cause potential injury to themselves.
Caution: The icon to the left indicates text that cautions readers against actions that could cause
potential injury to the product or the possibility of serious inconvenience.

Notices
6Epica DGX 16 and Epica DGX 32 Instruction Manual

Overview and General Specifications
7
Epica DGX 16 and Epica DGX 32 Instruction Manual
Overview and General Specifications
Applicability Notice
The information in this manual applies to the following Epica DGX 16 and 32 enclosures and
Epica DGX 16 and 32 pre-engineered systems. It also applies to Epica DGX Input and Output Boards,
which can be ordered separately. These boards are compatible in both the Epica DGX 16 and 32.
Note: All Epica DGX 16 and 32 enclosures ship with a standard front control panel.
Epica DGX 16 Enclosure (4 RU)
Epica DGX 32 Enclosure (6 RU)
Epica DGX 16 Pre-Engineered Systems (DVI Only)
Note: All Epica DGX 16 pre-engineered systems contain DVI Input and Output Boards only.
Epica DGX 32 Pre-Engineered Systems (DVI Only)
Note: All Epica DGX 32 pre-engineered systems contain DVI Input and Output Boards only.
Configuration FG # Model
16x16 FG1057-16 AVS-EPDGX16-ENC
Configuration FG # Model
32x32 FG1056-32 AVS-EPDGX32-ENC
Configuration FG # Model
16x16 FGP57-1616-DD0 AVS-EPDGX16-1616-DD0
8x16 FGP57-0816-DD0 AVS-EPDGX16-0816-DD0
16x8 FGP57-1608-DD0 AVS-EPDGX16-1608-DD0
Configuration FG # Model
16x16 FGP56-1616-DD0 AVS-EPDGX32-1616-DD0
16x24 FGP56-1624-DD0 AVS-EPDGX32-1624-DD0
16x32 FGP56-1632-DD0 AVS-EPDGX32-1632-DD0
24x16 FGP56-2416-DD0 AVS-EPDGX32-2416-DD0
24x24 FGP56-2424-DD0 AVS-EPDGX32-2424-DD0
24x32 FGP56-2432-DD0 AVS-EPDGX32-2432-DD0
32x16 FGP56-3216-DD0 AVS-EPDGX32-3216-DD0
32x24 FGP56-3224-DD0 AVS-EPDGX32-3224-DD0
32x32 FGP56-3232-DD0 AVS-EPDGX32-3232-DD0

Overview and General Specifications
8Epica DGX 16 and Epica DGX 32 Instruction Manual
Epica DGX 16 and 32 Input and Output Boards
For custom systems and for upgrading pre-engineered systems, the Epica DGX 16 and 32 currently each
support two board types: SC Optical and DVI. Each board fills one slot and has four connectors. Within a
system, a source connected to any of the input boards can be routed to any destination connected to any of
the output boards.
 For general board information, see page 12 and page 35.
 For specific board information, see the applicable board chapter in this manual.
Epica DGX DVI Boards (see page 53)
Epica DGX SC Optical Boards* (see page 47)
* DGX SC Optical Boards are used in conjunction with DGX Fiber Transmitter and Receiver modules.
For model numbers of the compatible modules, see page 48. For system setup information, see page 49.
Product Notes
The Epica DGX 16 and 32 are available in both pre-engineered (DVI only) and custom systems in a
variety of input to output configuration sizes and can contain an assortment of input and output boards in a
single enclosure. The Epica DGX 16 and 32 enclosures fit in a broad range of digital and analog
environments and are controllable from a variety of sources.
Note: Because the Epica DGX 16 and 32 Distribution Matrices are available in various board
configurations, the illustrations in this manual may differ from the model(s) you purchased.
Features of the Epica DGX 16 and 32
 The available input/output range for the Epica DGX 16 is 4x4 to 16x16 and for the
Epica DGX 32 the range is 4x4 to 32x32 (both come in increments of 4 with upgrade potential).
 DGX Technology provides a common signal transport and matrix switching layer that
transcodes between analog and digital signals.
 Supports uncompressed video resolutions up to 1920x1200 @ 60 Hz, including 1080p.
 Native NetLinx®device.
 AMX Device Discovery enabled through AMX’s AutoPatch Duet module.
 Designed for use with single strand multimode fiber.
 Use in conjunction with DGX Fiber Transmitters and Receivers to send video, audio, and
one-way control over a single fiber cable up to 6,000 feet (1828.8 m) – 3,000 feet (914.4 m)
to the Epica DGX 16 or 32 and 3,000 feet after the Epica DGX 16 or 32.
 DGX SC Optical Boards support RGBHV, RGBS, RGsB, and Y/Pb/Pr (Y/Pb/Pr including
1080p) video and DVI formats, depending on the type of DGX Fiber modules used with them.
 DGX SC Optical Boards support embedded analog stereo audio signals (unbalanced stereo
@ a sample rate of 48 kHz) and digital audio signals (PCM over S/PDIF @ 32 kHz, 44.1 kHz,
48 kHz, as well as 96 kHz, which requires a minimum video resolution of 800x600 @ 60 Hz).
 DGX SC Optical Boards also support unidirectional (source to destination) serial data.
 DGX DVI Boards only – provides increased power on every output for use with external DVI
extenders.
Type FG # Model
Input FG1056-520 AVS-EPDGX32-VI-DVI
Output FG1056-530 AVS-EPDGX32-VO-DVI
Type FG # Model
Input FG1056-500 AVS-EPDGX32-OI-SC
Output FG1056-510 AVS-EPDGX32-OO-SC

Overview and General Specifications
9
Epica DGX 16 and Epica DGX 32 Instruction Manual
Features of the Epica DGX 16 and 32 (continued)
 Compatible DGX Fiber Receivers feature SmartScale™Technology which automatically
responds to the display’s declared EDID information and scales the video to the best
resolution and video parameters for that display without manual setup.
 Pre-loaded with the most common EDID settings on each matrix switcher input connector
(other than fiber connectors) to emulate display response when queried, which makes sure
transmission of the video from the source device is working.
 Custom EDID settings can be loaded on each DVI input with the included EDID Programmer.
 System self-diagnostics (power monitoring, fan control and monitoring, signal and
temperature sensing); plus ships with APDiagnostics software (monitors, displays, and
collects advanced diagnostic information).
 Virtual matrices (levels) / groupings; ships with free matrix switcher configuration software.
 RJ-45 Ethernet (Enc Link) ports support linking to AMX AutoPatch matrix switchers.
 Local presets allow quick recall of a pre-programmed set of switches with a single command;
multiple presets can exist within a system at the same time.
 Global presets allow quick recall of a comprehensive snapshot of all switches.
 Standard RS-232 (Control) port.
 USB (mini-B) port can be used as a virtual Com port for serial communication with a PC.
 Fully redundant (hot-swappable) power supplies (RPS) with independent power paths for
maximum reliability.
 Rack mounting ears integral to product design.
 AMX Limited Lifetime Warranty included (see www.amx.com or the AMX AutoPatch CD).
 24-hour technical support.
Control Features for the Epica DGX 16 and 32
In addition to the front control panel, which is used for controlling the system’s switches and system
attributes, several control options are available. Multiple control methods can be used on the same
system.
 Front control panel (standard on all enclosures)
 Compatible with a number of AMX control devices (for control programming information,
see the instruction manual for the specific interface)
 APControl 3.0.1 software (free with all systems) provides easy single-user PC control
 Control via NXB-AP-1000 interface (server connection through TCP/IP port on CPU)
 Supports AMX AutoPatch’s simple BCS* serial control protocol
 Supports AMX AutoPatch’s XNNet protocol
 Supports third-party controllers
* BCS (Basic Control Structure) is sent as ASCII characters through the RS-232 port.
Note: Features and specifications described in this document are subject to change without notice.

Overview and General Specifications
10 Epica DGX 16 and Epica DGX 32 Instruction Manual
Front View
The enclosure, which is the structural basis of the Epica DGX 16 and 32 Distribution Matrices, can be
controlled using the standard front control panel, control software, or an external controller (for
additional information on control options, see page 15 and for control panel operation, see page 57). The
Power LED indicates the status of the power supplies.
Power LED on Front of Enclosure
The Power LED indicates the power status of the redundant power system within the
Epica DGX 16 and 32 enclosure as follows:
 Green – both power supplies are powered on
 Red – one of the power supplies is not receiving power or has failed
 Off – both power supplies are not receiving power
Rear View
The enclosure’s appearance, as viewed from the rear, will vary depending on the number and types of
input and output boards present. The Epica DGX 16 enclosure in FIG. 2 is fully loaded for 16x16
switching. The Epica DGX 32 enclosure in FIG. 3 is partially loaded for 28x28 switching.
Epica DGX 16
FIG. 1 Front view of an Epica DGX 32 enclosure
FIG. 2 Rear view of a full Epica DGX 16 enclosure
LCD Power IndicatorControl Dial
Control Keys Output Keys
Input Keys
Input boards (up to 4) Output boards (up to 4)
Power supplies
Serial number CPU/Control board
Note: Empty input or output
can be used to upgrade
numbered for expansion)
system.
board slots (which are

Overview and General Specifications
11
Epica DGX 16 and Epica DGX 32 Instruction Manual
Epica DGX 32
Rear View Components
 Input and output boards (some slots may be empty, depending on the configuration)
 CPU/Control board
 Two standard redundant power supplies
 Serial number
The following sections briefly introduce the hardware on the rear of the enclosure.
CPU/Control Board
The CPU/Control board (FIG. 4) is on the left rear of the enclosure, directly below the input connectors.
Each CPU includes the following port options:
 Enc Link port (Ethernet RJ-45) – for linking to other types of enclosures (see page 24)
 Control port (DB-9, RS-232) – for attaching an external control device (see page 29)
 USB (mini-B) port – for attaching an external control device (see page 32)
 TCP/IP (RJ-45) port – for establishing an NXB-AP-1000 connection (see page 42)
Each CPU includes two main LED indicators:
 System Status indicator (between the Enc Link ports and the Control port) –for system status
 NXB-AP-1000 LED Indicator (left of TCP/IP port) – indicates an active connection
FIG. 3 Rear view of an Epica DGX 32 enclosure with room for expansion
FIG. 4 CPU/Control board
Power supplies
Serial number
Input boards (up to 8)
CPU/Control board
Output boards (up to 8)
Empty input and output
Note: Empty input or output
can be used to upgrade
numbered for expansion)
system.
board slots (which are
board slots
USB (mini-B) port
Enc Link ports (Ethernet RJ-45, 10/100), use for linking enclosures
Control (DB-9, RS-232 serial) portSystem Status indicator
TCP/IP (RJ-45) port
NXB-AP-1000
LED indicator
Epica DGX 32 rear view

Overview and General Specifications
12 Epica DGX 16 and Epica DGX 32 Instruction Manual
Power Supply Units
Each of the power supply units on the rear of the enclosure (FIG. 5) has a power receptacle that will
accept all major international standard power sources. (US power cords are included with all shipments
unless ordered otherwise.) Maximum power specifications are provided on the power supply
receptacles.
For information on applying power, see page 36.
The power supply unit has three LED indicators (in order from left to right):
 AC ( ): When the LED is green, the power is good.
 DC ( ): When the LED is green, the power is good.
 Temperature ( ): When the LED is not illuminated, the temperature is good; when the LED
is amber, the temperature is above normal.
Caution: Each power supply has a small toggle switch to the left of its LEDs that controls internal
power and must remain flipped to the right for the system to operate. Do not flip this switch to the left.
Input and Output Boards
A single enclosure can handle a combination of signals: the DVI boards support DVI-D signals, and the
SC Optical boards support DVI-D, analog video,* and digital or analog stereo audio signals. All signals
are automatically converted to the output device’s format, with DGX Fiber Modules used in the
conversion process for the DGX SC Optical boards.
* Supported analog video signals include RGBHV, RGBS, RGsB, and Y/Pb/Pr.
Epica DGX 16
Epica DGX 16 enclosures have 8 horizontal board slots (4 slots each for input and output boards with
four connectors each), allowing for a maximum configuration of 16x16.
FIG. 5 Power supply receptacles, LEDs, and switches
FIG. 6 DGX DVI and DGX SC Optical Input and Output Boards
3 Indicator LEDs
Leave switch on
(flipped right)
Input boards Output boards
DGX DVI Board
DGX SC Optical Board

Overview and General Specifications
13
Epica DGX 16 and Epica DGX 32 Instruction Manual
Epica DGX 32
Epica DGX 32 enclosures have 16 vertical board slots (8 slots each for input and output boards with four
connectors each), allowing for a maximum configuration of 32x32.
For information on the boards included in your system, including connector types, cabling directions, and
specifications, see the specific board chapter in this manual. If a system has empty board slots, the slots can
be used to upgrade the system. For information on adding or replacing boards, see “Appendix E –Board
Replacement” on page 145.
Input and Output Connectors
The connectors on the input and output boards are the attachment points for source and destination devices
that connect to the system. Viewed from the rear of the enclosure, the input connectors (for attaching
sources) are on the left, and the output connectors (for attaching destinations) are on the right.
Input and output channel numbers correspond to the connectors and are located as follows:
 Epica DGX 16 – on the vertical numbering plate (metal strip) between the input and output
connectors.
 Epica DGX 32 – on the horizontal numbering plate (metal strip) directly above the connectors.
Serial Number
The serial number is normally located on the rear of the enclosure on the left (FIG. 2 on page 10 and
FIG. 3 on page 11). Before installation, we recommend recording the serial number for each enclosure (and
for each module if applicable) in the system in an easily accessible location.
FIG. 7 DGX DVI and DGX SC Optical Input and Output Boards
DGX DVI Board
DGX SC Optical Board
Input boards Output boards
Empty input and output
be used to upgrade system
numbered for expansion) can
board slots (which are

Overview and General Specifications
14 Epica DGX 16 and Epica DGX 32 Instruction Manual
Epica DGX 16 General Specifications
Epica DGX 32 General Specifications
For individual board information and specifications, see the specific board chapter in this manual.
 DGX SC Optical Boards – see page 47
 DGX DVI Boards – see page 53
Note: Features and specifications described in this document are subject to change without notice.
Specifications
Parameter Value
Approvals CE, UL, cUL, FCC Class A, RoHS
AC Power per Supply 100 VAC to 240 VAC single phase, 50 Hz to 60 Hz
Power Consumption (max.) 785 Watts
Power Consumption (typical) 210 Watts, fully loaded enclosure
Thermal Dissipation (max.) 2679 BTU/hr.
Thermal Dissipation (typical) 717 BTU/hr, fully loaded enclosure
Operational Temperature 32° F to 113° F (0° C to 45° C)
Storage Temperature -22° F to 158° F (-30° C to 70° C)
Humidity 0 to 90% non-condensing
MTBF 170,000 hours
Dimensions 15 in. (38.1 cm) depth; 16 in. (40.64 cm) with extractors
19 in. (48.26 cm) width including integral rack mounting ears
6.84 in. (17.37 cm) height (4 RU)
Weight Approximately 34 lb. (15.4 kg) per loaded enclosure
Shipping Weight Approximately 40 lb. (18.1 kg) per loaded enclosure
Compatible Fiber Modules AMX AutoPatch DGX Fiber TX and DGX Fiber RX modules
Specifications
Parameter Value
Approvals CE, UL, cUL, FCC Class A, RoHS
AC Power per Supply 100 VAC to 240 VAC single phase, 50 Hz to 60 Hz
Power Consumption (max.) 785 Watts
Power Consumption (typical) 445 Watts, fully loaded enclosure
Thermal Dissipation (max.) 2679 BTU/hr.
Thermal Dissipation (typical) 1518 BTU/hr., fully loaded enclosure
Operational Temperature 32° F to 113° F (0° C to 45° C)
Storage Temperature -22° F to 158° F (-30° C to 70° C)
Humidity 0 to 90% non-condensing
MTBF 102,000 hours
Dimensions 20.08 in. (51 cm) depth; 21.08 in. (53.54 cm) with extractors
19 in. (48.26 cm) width including integral rack mounting ears
10.45 in. (26.54 cm) height (6 RU)
Weight Approximately 60 lb. (27.2 kg) per loaded enclosure
Shipping Weight Approximately 70 lb. (31.8 kg) per loaded enclosure
Compatible Fiber Modules AMX AutoPatch DGX Fiber TX and DGX Fiber RX modules