AN SON ASI-8920 User manual

http://www.ansoncorp.com
4. Installation Instruction
4.1 Remove the two keys first. 4.2 Unfasten the two screws.
485 23 2
JP1
5. Communication Mode Setup
JP1
485 232 485 232
JP1
RS232 ModeRS485 Mode
Change the communication mode with computer by changing the jumper-
wire in jumper JP1
485 232
GND
12V
DAT0
DAT1
SW GND
Men C1
BEL L
BEL L
RX
TX
GND
485 +
485 -
2C
2NO
1NO
1C
1NC
Read the manual before usage and keep for
future reference.
User Manual
ASI-8920
Integrated
Access Controller
Failure to follow the instructions below may lead to the malfunction of
the system, property damage and even physical injury.
2.1 Connection and operation on any components or the controller with power on is
2.2 Connect the system according to the instructions described in this manual.
2.3 The RS232 cable connected to the computer should be no more than 15 meters.
2.4 The RS485 cable connected to the computer should be no more than 1200m.
2.5 Please use the specified power supply.
2.6 The communication mode between the controller and computer should be either
2.7 When RS485 mode is applied, a highway can connect maximally 32 controllers
strictly prohibited.
RS232 or RS485.
with identification address differs from each other.
232 4 85
JP1
232 4 85
JP1
232 4 85
JP1
232 4 85
JP1
6. Rules for Installation
6.1 Selection of exterior components may be based on installation environment.
However, the selection should be in accordance to existing National and
International Standards as well as matched with the controller. A careful study on
the instructions on exterior components selection is strongly advised.
6.2 Installation of the control unit (including microprocessor) should not be inside the
high-voltage box or near any large converter or high voltage/current devices. The
components should be installed in places easy for uninstallation in order for
convenient maintenance.
6.3 The controller board should be connected to earth independently. Please ensure
that grounding has been provided in the installation site.
6.4 When installing the box with microprocessors inside, please ensure that the screw
and lock has been fastened.
6.5 The 220V terminal power cable should be plugged in separate power supply socket
(the power cable should not share the socket with other devices) with grounding
ensured.
6.6 Do not crossover the system cables through other devices.
6.7 All components should not be installed in places with excess high/low temperature
or humidity.
3.1 Electric Parameters
Working Voltage: DC9-15V Anti-static Capability: ≥15KV
Static Current: ≤110mA Relative Humidity: 0%-95%
Input Interface: Stem joint switch input
Working Temperature:-10℃to 55℃
Drive Capability: 2 groups of Type C Relay output, DC12V/3A
Power-off Protection: Data will be preserved for 10 years when power off
3.2 Type of Card : EM card or compatible EM Card
3.3 I/O Interface: 2 groups of switch input, 1 group anti-disassemble alarm input, 1
exterior card interface, 2 groups of output interfaces, DC12/3A
3.4 Network Interface: RS232/RS485 interface
Communication Rate: 9600bps
3.5 System Capacity and Main Functions
Number of Card Holder: 3000
Number of Records: 8200 pcs Entrance/Exit Mode:
——Card alone ——Card plus Password
——Password alone ——Initial Card Open
——Multiple Card Open (2≤N≤4)
——Remote Open ——Forced Open
Multiple and programmable working modes:
——Normal Open
——Forced Close
——Identification after Card-presenting (Door will be opened only after the card
holder is identified by the control center)
——Anti-passback function
Multiple access group and working hour setup
——Every controller supports 42 access groups
——Support 20 groups of schedule
——Support 32 groups of annual holiday setup
Protection
——All inputs are equipped with advanced TVS protection
——Voltage clamp protection
——All outputs adopt spark depress circuit and absorption circuit
——Four-layer PCB structures enhances anti-EMI capability
1.1 Structure and Appearance design of Anson ASI-8930 and ASI-8920 are patented
1.2 Color: pure black, black decorated with silver
1.3 Size: L×W×H (mm): 150×88×30
and any sort/form of copy and counterfeit will be charged.
123
456
789
0 #
123
456
789
0 #
ASI- 89 30 A SI-8920
7. Instruction for Keypad Function
Sound Indication:
One sound means correct input, co ntinuous ly sound twice means err or or
Light Indication:
Blue light is for power, green for valid, yellow for Edit, yellow flash for “Waiting to input
password”, and yellow light on for “Editing sta tu s en te re d”
Keypad Edit:
Wait for 6 seconds after inputing password/card+password
7.1 Enter/Exit Edit mode
Push “*”, yellow light flashes=>input administrator password, yellow light on,
Edit status entered. (D ef au lt a dm in istrator password is “000000”.
If password is not inputted or wrongly inputted within 20s, sound twice and
exit Edit status, orange light off and blue light on).
Push “#” to exit Edit status.
7.2 Basic setup
Basic setup includes: system initiation, address setup, anti-disassemble alarm
setup, d oo r-o pe n setup.
7.2.1 System Initiation
Sys tem init iation will clea r all original setu p of the controller (includ ing pass
m od e setup, basic setup, all keyp ad -ad de d card, password etc. however,
administrator setup will not be changed).
7.2.2 Setup address
Address is applied to differentiate the controller from any other devices on the
network. An address within a single 485 ne tw or k sh ou ld b e unique.
7.2.3 Ant i- di sa ss em bl e al ar m se tu p
Anti-disassemble alarm is applied to protect controller from being disassembled
o r da ma ged.
7.2.4 Door-open Setup
exi t.
读卡器
接口1
485 232
GND
12V
DAT0
DAT1
SW
GND
MenC1
GND
BELL
BELL
RX
TX
GND
485+
485-
2C
2NO
1NO
1C
1NC
①① ②② ③③
+B-B
+12VG ND +12 GN D
AC9 0~22 0V
PWD RxD TxD
RS485
RS232
12345
AC 90~220V
Detailed installation procedure, Refer to Installation & Commissioning
Manual. Strictly follow the diagram for connection.
Any modification will be notified.
262 0
1 2 3
456
789
0 #
GND
+12V
DATA0
DATA1
NC
COM
NO
V-
V+
Access Controller
EM Lock
Alarm Light
RS485-RS232
Convertor
Computer
Interface
DB9-Hole
Computer
Interface
Door
Magnet
Exit Button
Exterior Reader
Controller Power
Controller Wiring Diagram
Doorbell
Connected with
Fail-Secure
T/R+
T/R-
GND
7.3 Pass Mode Setu
This function is used to define the mode of pass, including three modes:
car d, card plus pas sword an d password. For card+p assword and password
mod e, the door-open passw ord and card-hol der passwor d are the same
7.4 Off-line user manag em en t
his function en ab le s the user to manage car d- ho ld er s by the integrated
access controller without connecting t o co mp ut er.
Max. 1500 cards/card-holders can be mana ge d in O ff-line manage
mode. There is no con fl ic t bet we en off- li ne c ar ds a nd c ar ds r ea d by
computer. The o ff -l in e card possesses top authority and is not affected
by such functions as multiple card, i ni ti al c ar d, remote control, anti-
passback and access level.
7.4.1 Add m ul ti pl e ca rd s
A number of c ar ds c an b e re gi st er ed i n th e de vi ce , w it h a de si gn at ed
first number. The s ec on d card wi ll be assigned wi th a nu mb er n ex t to th e
number de si gn at ed to the first ca rd . Thi s continues unt il user exi ts t he
function automatically or manually.
7.4.2 Add s in gl e ca rd
Us er ca n d esi gn ate a ce rta in nu mbe r to a ca rd. O nly o ne car d can be
designated in on e time. If the number ha s been designated to other card
before, th e newly designated card will o ve rw ri te the original card (the on e
with this number before).
7.4.3 Delete one card
User can in validate a c ar d by delete th e ca rd n um be r re gi st er ed i n th e
controller. Only one card can be deleted i n on e ti me .
7.4.4 Delete Al l Ca rd s
This f un ct io n will in va li da te all th e keypad-registered c ar ds ; similarly,
initiation w il l also clear al l cards. Pl ea se b e warned fo r applying this
function.
7.5 Password management
Password m an ag em en t re fe rs t o th e management of administrator
password and card-holder password.A dm in is tr at or password i s used to
enter Ed it s ta tu s.C ar d- ho ld er password is used to o pe n the d oo r in the
password or card+password door-ope n mo de .
7.5.1 Set card-holder password
Ca rd -h ol de r password can b e a pp li ed in both t he pa ss wo rd and the
card+password door-open mode. In the “Screen Door-open
Password” mode, password only is ineffective for opening door.
7.5.2 Set administrator password
Default administrator password is 000000
If a numbe r has been de signated t o ot her car d befor e, the newly designat ed
car d will overwrite the ori ginal ca rd (t he one with this num ber before).
input 11 wait for 3 second, blue light on, exit Edit status
exit Edit, address is set as 29
exit Edit status
input 14
input Edit code(00: cancel alarm, 01 initiate alarm)
Open with card
Edit input 223 door will be opened once the card is valid
Card plus password
Edit input 234 door will be opened once the card is valid and
card-holder password is correctly inputted
Screen door-open password
Edit input 243
Door-open password
Edit input 254
input door-open password (card-holder pass-
word) can not open the door
input door-open password (card-holder pass-
word) can open the door
Edit input 31 input 4-digit initial number
(range from 0000-1499)
complete input and push # to exit read the card and device sounds
once,then read the second card
Edit input 32 input 4-digit number (range 0000-1499)
read the card and device sounds once, exit automatically
exit automatically. If sounds twice, error occurs
and password setting is ineffective. input 6-digit password again
exit automatically. If sounds twice,error
occurs and password setting is ineffective.
Edit input 33 input 4-digit number (0000-1499)
exit automatically, the card deleted is invalidated
Edit input 41
input 6-digit password, yellow light flashes
Edit input 42 input 6-digit password, yellow light flashes
input 6-digit password again
Edit input 34 Automatic exit, all off-line subscribers
will be cleared.
input 21
input door-open duration (range 00-99 second)
exit Edit
input 12 input address e.g. 29 (range 00-39)
4.3 Open the back cover and connect the
device according to the wiring diagram.
4.4 Fix the backcover on the wall and
reassemble the device. (according to
4.1, 4.2 and 4.3 in reversed order)
First open the lower
part of backcover
for around 1cm.
Please note that
open too wide may
lead to damage to
the device.
push up the back cover
to open
Sustained Effort for the Better
1 2 3
456
789
0 #
3. Product Parameters
Edit
Edit
Edit
Edit
2. Important Notices
1. Model and Appearance