Analog Devices ADSP-TS201S EZ-KIT Lite User manual

ADSP-TS201S EZ-KIT Lite®
Evaluation System Manual
Revision 3.1, April 2007
Part Number
82-000770-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106 a

Copyright Information
©2007 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materi-
als and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices icon bar and logo, TigerSHARC, TigerSHARC logo,
VisualDSP++, the CROSSCORE logo, and EZ-KIT Lite are registered
trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-TS201S EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-TS201S EZ-KIT Lite evaluation system had been appended to
Analog Devices Development Tools Technical Construction File refer-
enced “DSPTOOLS1” dated December 21, 1997 and was awarded CE
Certification by an appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD (electrostatic
discharge) sensitive devices. Electrostatic charges readily accumu-
late on the human body and equipment and can discharge without
detection. Permanent damage may occur on devices subjected to
high-energy discharges. Proper ESD precautions are recommended
to avoid performance degradation or loss of functionality. Store
unused EZ-KIT Lite boards in the protective shipping package.

ADSP-TS201S EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xii
Intended Audience ......................................................................... xii
Manual Contents ........................................................................... xii
What’s New in This Manual .......................................................... xiii
Technical or Customer Support ...................................................... xiv
Supported Processors ...................................................................... xiv
Product Information ....................................................................... xv
MyAnalog.com .......................................................................... xv
Processor Product Information ................................................... xv
Related Documents .................................................................. xvi
Online Technical Documentation ............................................ xvii
Accessing Documentation From VisualDSP++ .................... xviii
Accessing Documentation From Windows .......................... xviii
Accessing Documentation From Web ................................... xix
Printed Manuals ....................................................................... xix
VisualDSP++ Documentation Set ......................................... xix
Hardware Tools Manuals ...................................................... xix
Processor Manuals ................................................................. xx

CONTENTS
vi ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Data Sheets .......................................................................... xx
Notation Conventions ................................................................... xxi
USING ADSP-TS201S EZ-KIT LITE
Package Contents ......................................................................... 1-2
Default Configuration .................................................................. 1-3
Installation and Session Startup ..................................................... 1-5
Evaluation License Restrictions ..................................................... 1-7
Memory Map ............................................................................... 1-7
SDRAM Interface ......................................................................... 1-8
Flash Memory .............................................................................. 1-9
Programmable FLAG Pins .......................................................... 1-10
Interrupt Pins ............................................................................. 1-11
Audio Interface ........................................................................... 1-12
Processor Link Ports ................................................................... 1-12
Example Programs ...................................................................... 1-13
Flash Programmer Utility ............................................................ 1-14
ADSP-TS201S EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
External Port ........................................................................... 2-3
Expansion Interface ................................................................. 2-3
JTAG Emulation Port ............................................................. 2-4
Switch Settings ............................................................................. 2-5
Audio Amplification Selection (SW1) ...................................... 2-5

ADSP-TS201S EZ-KIT Lite Evaluation System Manual vii
CONTENTS
Processor Mode Selections (SW2) ............................................ 2-6
Processor Boot Strap Settings .............................................. 2-7
SYSCON/SDRCON Mode Settings .................................... 2-7
Interrupt Enable Settings .................................................... 2-8
Link Port Width Settings .................................................... 2-8
FLAGs and IRQs Switch Settings (SW10) ................................ 2-9
Configuration Resistors ............................................................... 2-10
Processor ID Settings ............................................................. 2-10
Clock Mode Settings ............................................................. 2-12
Control Impedance Selection ................................................. 2-14
Drive Strength Selection ........................................................ 2-15
LEDs and Push Buttons .............................................................. 2-16
Power LED (LED1) ............................................................... 2-16
Reset LED (LED8) ................................................................ 2-16
FLAG LEDs (LED3–6) ......................................................... 2-17
USB Monitor LED (ZLED3) ................................................. 2-18
Programmable FLAG Push Buttons (SW6–9) ......................... 2-18
Interrupt Push Buttons (SW4 and SW5) ................................ 2-19
Reset Push Button (SW3) ...................................................... 2-19
Connectors ................................................................................. 2-20
Audio (J9 and J10) ................................................................ 2-21
Power (J8) ............................................................................. 2-21
JTAG (ZP4) .......................................................................... 2-21
USB (ZJ1) ............................................................................. 2-22

CONTENTS
viii ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Expansion Interface (J1–3) .................................................... 2-22
Link Ports (J4–7) .................................................................. 2-23
Power Supply Specifications ........................................................ 2-23
ADSP-TS201 EZ-KIT LITE BILL OF MATERIALS
ADSP-TS201S EZ-KIT LITE SCHEMATIC
Title Page ..................................................................................... B-1
Processor A ................................................................................... B-2
Processor B ................................................................................... B-3
Processor Link Ports ..................................................................... B-4
Processor Power ............................................................................ B-5
Configuration ............................................................................... B-6
Memory ....................................................................................... B-7
Audio In ....................................................................................... B-8
Audio Out .................................................................................... B-9
Reset/PB/LED ............................................................................ B-10
Expansion Interface .................................................................... B-11
JTAG/CPLD For Audio .............................................................. B-12
Power Page 1 .............................................................................. B-13
Power Page 2 .............................................................................. B-14
Processor Bypass Caps ................................................................. B-15
INDEX

PREFACE
Thank you for purchasing the ADSP-TS201S EZ-KIT Lite®, Analog
Devices (ADI) evaluation system for TigerSHARC®floating-point
embedded processors.
The TigerSHARC processor is a static super scalar (SSS) architecture tar-
geted at software-defined radio applications. In these wireless
infrastructure applications, the TigerSHARC processor is replacing
field-programmable gate arrays (FPGAs) in the chip rate processing appli-
cations for third generation cellular. The performance, flexibility,
multiprocessing and IO capabilities of the TigerSHARC processor makes
it superior to FPGA implementations.
The evaluation board is designed to be used in conjunction with the Visu-
alDSP++®development environment to test the capabilities of the
ADSP-TS201S TigerSHARC processor. The VisualDSP++ development
environment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-TS201S assembly
• Load, run, step-in, step-out, step-over, halt, and set breakpoints in
application program
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
ADSP-TS201S EZ-KIT Lite Evaluation System Manual ix

x ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Access to the ADSP-TS201S processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-TS201S processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools/.
The ADSP-TS201S EZ-KIT Lite provides example programs to demon-
strate the capabilities of the evaluation board.
LThe ADSP-TS201S EZ-KIT Lite installation is part of the Visu-
alDSP++ installation. The EZ-KIT Lite is a licensed product that
offers an unrestricted evaluation license for the first 90 days. For
details about evaluation license restrictions after the 90 days, refer
to “Evaluation License Restrictions” on page 1-7.
Refer to the VisualDSP++ Installation Quick Reference Card for details.
The board features:
• Two Analog Devices ADSP-TS201S processors
D500 MHz core clock speed
DConfigurable core clock mode
• Analog Devices AD1871 96 kHz analog-to-digital converter
DLine-in 3.5 mm stereo jack
• Analog Devices AD1854 96 kHz digital-to-analog converter
DLine-out 3.5 mm stereo jack
• SDRAM memory
D32 MB (4 MB x 64)

ADSP-TS201S EZ-KIT Lite Evaluation System Manual xi
Preface
• Flash memory
D512K main flash memory
• USB debugging interface
• Interface connectors
D14-pin emulator connector for JTAG interface
DLow Voltage Differential Signaling (LVDS) link ports via
RJ-45 connectors
DExpansion interface connectors
• General-purpose IO
D4 push button flags (two for each processor)
D2 push button interrupts (one for each processor)
D4 LED FLAG outputs (two for each processor)
• Analog Devices ADP3331, ADP3336, ADP1864, ADP1821, and
ADP1823 voltage regulators
The EZ-KIT Lite board contains two external memories: flash memory
and SDRAM. The flash memory can be used to store user-specific boot
code. By configuring the boot mode switch (SW2) and programming the
flash memory, the board can run as a stand-alone unit. The SDRAM is
shared by both processors and can be used to store data external to the
processors. For more information, see “Memory Map” on page 1-7.
The EZ-KIT Lite board contains an audio interface, facilitating creation
of audio signal processing applications.
Additionally, the EZ-KIT Lite board provides expansion connectors,
allowing you to connect to the processor’s external port (EP).

Purpose of This Manual
xii ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Purpose of This Manual
The ADSP-TS201S EZ-KIT Lite Evaluation System Manual provides
instructions for installing the product hardware (board). The text
describes the operation and configuration of the board components and
provides guidelines for running your own code on the ADSP-TS201S
EZ-KIT Lite. Finally, a schematic and a bill of materials are provided as a
reference for future designs.
The product software installation is detailed in the VisualDSP++ Installa-
tion Quick Reference Card.
Intended Audience
The primary audience of this manual is a programmer who is familiar with
Analog Devices processors. This manual assumes that the audience has a
working knowledge of the appropriate processor architecture and instruc-
tion set. Programmers who are unfamiliar with Analog Devices processors
can use this manual but should supplement it with other texts (such as the
ADSP-TS201 TigerSHARC Processor Hardware Reference and the
ADSP-TS201 TigerSHARC Processor Programming Reference) that describe
your target architecture.
Programmers who are unfamiliar with VisualDSP++ should refer to the
VisualDSP++ online Help and user’s or getting started guides. For the
locations of these documents, see “Related Documents”.

ADSP-TS201S EZ-KIT Lite Evaluation System Manual xiii
Preface
Manual Contents
The manual consists of:
• Chapter 1, “Using ADSP-TS201S EZ-KIT Lite” on page 1-1
Provides information on the EZ-KIT Lite from a programmer’s
perspective and outlines the board’s memory map.
• Chapter 2, “ADSP-TS201S EZ-KIT Lite Hardware Reference” on
page 2-1
Provides information on the hardware aspects of the EZ-KIT Lite.
• Appendix A, “ADSP-TS201 EZ-KIT Lite Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the EZ-KIT
Lite board.
• Appendix B, “ADSP-TS201S EZ-KIT Lite Schematic” on
page B-1
Provides the resources to allow EZ-KIT Lite board-level debugging
or to use as a reference design.
LAppendix B now is part of the online Help. The PDF version of
the ADSP-TS201S EZ-KIT Lite Evaluation System Manual is
located in the Docs\EZ-KIT Lite Manuals folder on the installation
CD. Alternatively, the schematic can be found on the Analog
Devices Web site: www.analog.com/processors.
What’s New in This Manual
This edition of the ADSP-TS201S EZ-KIT Lite Evaluation System Manual
documents ADSP-TS201S EZ-KIT Lite compliance with the RoHS and
WEEE directives.

Technical or Customer Support
xiv ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
http://www.analog.com/processors/technicalSupport
• E-mail tools questions to
[e-mail]
• E-mail processor questions to
[email protected]m (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Phone questions to 1-800-ANALOGD
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
The ADSP-TS201S EZ-KIT Lite evaluation system supports the Analog
Devices ADSP-TS201S TigerSHARC embedded processors.

ADSP-TS201S EZ-KIT Lite Evaluation System Manual xv
Preface
Product Information
You can obtain product information from the Analog Devices website,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our Web site provides infor-
mation about a broad range of products—analog integrated circuits,
amplifiers, converters, and embedded processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices Web site that allows
customization of a Web page to display only the latest information on
products you are interested in. You can also choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests. MyAnalog.com provides access to books, application notes, data
sheets, code examples, and more.
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
e-mail address.
Processor Product Information
For information on embedded processors and DSPs, visit our Web site at
www.analog.com/processors, which provides access to technical publica-
tions, data sheets, application notes, product overviews, and product
announcements.

Product Information
xvi ADSP-TS201S EZ-KIT Lite Evaluation System Manual
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• E-mail questions or requests for information to
[email protected]m (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Fax questions or requests for information to
1-781-461-3010 (North America)
[phone] (Europe)
Related Documents
For information on product related development software, see the follow-
ing publications.
Table 1. Related Processor Publications
Title Description
ADSP-TS201S Embedded Processor Data
Sheet
General functional description, pinout, and timing
ADSP-TS201 TigerSHARC Processor
Hardware Reference
Description of internal processor architecture and
all register functions
ADSP-TS201 TigerSHARC Processor Pro-
gramming Reference
Description of all allowed processor assembly
instructions
Table 2. Related VisualDSP++ Publications
Title Description
VisualDSP++ User’s Guide Description of VisualDSP++ features and usage
VisualDSP++ Assembler and Preprocessor
Manual
Description of the assembler function and com-
mands
VisualDSP++ C/C++ Complier and
Library Manual for TigerSHARC Processors
Description of the complier function and com-
mands for TigerSHARC processors

ADSP-TS201S EZ-KIT Lite Evaluation System Manual xvii
Preface
All documentation is available online. Most documentation is available in
printed form.
LIf you plan to use the EZ-KIT Lite board in conjunction with a
JTAG emulator, also refer to the documentation that accompanies
the emulator.
Visit the Technical Library Web site to access all processor and tools man-
uals and data sheets:
http://www.analog.com/processors/technicalSupport/technicalLi-
brary/.
Online Technical Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, the Dinkum
Abridged C++ library, and Flexible License Manager (FlexLM) network
license manager software documentation. You can easily search across the
entire VisualDSP++ documentation set for any topic of interest. For easy
printing, supplementary .pdf files of most manuals are provided in the
Docs folder on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
If documentation is not installed on your system as part of the software
installation, you can add it from the VisualDSP++ CD at any time by run-
ning the Tools installation. Access the online documentation from the
VisualDSP++ environment, Windows®Explorer, or the Analog Devices
Web site.
VisualDSP++ Linker and Utilities Manual Description of the linker function and commands
VisualDSP++ Loader and Utilities Manual Description of the loader/splitter function and com-
mands
Table 2. Related VisualDSP++ Publications (Cont’d)
Title Description

Product Information
xviii ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Accessing Documentation From VisualDSP++
To view VisualDSP++ Help, click on the Help menu item or go to the
Windows task bar and navigate to the VisualDSP++ documentation via
the Start menu.
To view ADSP-TS201S EZ-KIT Lite Help, which is part of the Visu-
alDSP++ Help system, use the Contents or Search tab of the Help
window.
Accessing Documentation From Windows
In addition to any shortcuts you may have constructed, there are many
ways to open VisualDSP++ online Help or the supplementary documenta-
tion from Windows.
Help system files (.chm) are located in the Help folder, and .pdf files are
located in the Docs folder of your VisualDSP++ installation CD-ROM.
The Docs folder also contains the Dinkum Abridged C++ library and the
FlexLM network license manager software documentation.
Your software installation kit includes online Help as part of the Win-
dows®interface. These help files provide information about VisualDSP++
and the ADSP-TS201S EZ-KIT Lite evaluation system.
File Description
.chm Help system files and manuals in Help format
.htm or
.html
Dinkum Abridged C++ library and FlexLM network license manager software doc-
umentation. Viewing and printing the .html files requires a browser, such as
Internet Explorer 5.01 (or higher).
.pdf VisualDSP++ and processor manuals in Portable Documentation Format (PDF).
Viewing and printing the .pdf files requires a PDF reader, such as Adobe Acrobat
Reader (4.0 or higher).

ADSP-TS201S EZ-KIT Lite Evaluation System Manual xix
Preface
Accessing Documentation From Web
Download manuals at the following Web site:
http://www.analog.com/processors/technicalSupport/technicalLi-
brary/.
Select a processor family and book title. Download archive (.zip) files,
one for each manual. Use any archive management software, such as Win-
Zip, to decompress downloaded files.
Printed Manuals
For general questions regarding literature ordering, call the Literature
Center at 1-800-ANALOGD (1-800-262-5643) and follow the prompts.
VisualDSP++ Documentation Set
To purchase VisualDSP++ manuals, call 1-603-883-2430. The manuals
may be purchased only as a kit.
If you do not have an account with Analog Devices, you are referred to
Analog Devices distributors. For information on our distributors, log onto
http://www.analog.com/salesdir/continent.asp.
Hardware Tools Manuals
To purchase EZ-KIT Lite and in-circuit emulator (ICE) manuals, call
1-603-883-2430. The manuals may be ordered by title or by product
number located on the back cover of each manual.

Product Information
xx ADSP-TS201S EZ-KIT Lite Evaluation System Manual
Processor Manuals
Hardware reference and instruction set reference manuals may be ordered
through the Literature Center at 1-800-ANALOGD (1-800-262-5643),
or downloaded from the Analog Devices Web site. Manuals may be
ordered by title or by product number located on the back cover of each
manual.
Data Sheets
All data sheets (preliminary and production) may be downloaded from the
Analog Devices Web site. Only production (final) data sheets (Rev. 0, A,
B, C, and so on) can be obtained from the Literature Center at
1-800-ANALOGD (1-800-262-5643); they also can be downloaded from
the Web site.
To have a data sheet faxed to you, call the Analog Devices Faxback System
at 1-800-446-6212. Follow the prompts and a list of data sheet code
numbers will be faxed to you. If the data sheet you want is not listed,
check for it on the Web site.