Analog Devices EZ-KIT Lite ADSP-BF533 User manual

ADSP-BF533 EZ-KIT Lite®
Evaluation System Manual
Revision 1.3, April 2004
Part Number
82-000730-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106 a

Copyright Information
© 2004 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materi-
als and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, VisualDSP++, VisualDSP++ logo, Blackfin,
CROSSCORE logo, and EZ-KIT Lite are registered trademarks of Analog
Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-BF533 EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-BF533 EZ-KIT Lite evaluation system had been appended to
the Technical Construction File referenced “DSPTOOLS1” dated
December 21, 1997 and was awarded CE Certification by an appointed
European Competent Body as listed below.
Technical Certificate No: Z600ANA1.011
Issued by: Technology International (Europe) Limited
41 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TZ, UK
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electro-
static charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.

CONTENTS
iv ADSP-BF533 EZ-KIT Lite Evaluation System Manual

ADSP-BF533 EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xiv
Intended Audience ......................................................................... xiv
Manual Contents ............................................................................ xv
What’s New in This Manual ........................................................... xvi
Technical or Customer Support ...................................................... xvi
Supported Processors ..................................................................... xvii
Product Information ..................................................................... xvii
MyAnalog.com ........................................................................ xvii
DSP Product Information ....................................................... xviii
Related Documents ................................................................ xviii
Online Documentation ............................................................. xx
Printed Manuals ........................................................................ xx
VisualDSP++ Documentation Set .......................................... xx
Hardware Manuals ............................................................... xxi
Data Sheets .......................................................................... xxi
Contacting DSP Publications .................................................... xxi
Notation Conventions ................................................................... xxii

CONTENTS
vi ADSP-BF533 EZ-KIT Lite Evaluation System Manual
GETTING STARTED
Contents of EZ-KIT Lite Package ................................................. 1-1
PC Configuration ......................................................................... 1-3
Installation Tasks .......................................................................... 1-3
Installing VisualDSP++ and EZ-KIT Lite Software .................. 1-4
Installing and Registering VisualDSP++ License ....................... 1-5
Setting Up EZ-KIT Lite Hardware .......................................... 1-5
Installing EZ-KIT Lite USB Driver ......................................... 1-7
Windows 98 USB Driver .................................................... 1-8
Windows 2000 USB Driver .............................................. 1-12
Windows XP USB Driver ................................................. 1-13
Verifying Driver Installation .................................................. 1-15
Starting VisualDSP++ ........................................................... 1-16
USING EZ-KIT LITE
EZ-KIT Lite License Restrictions .................................................. 2-2
Memory Map ............................................................................... 2-2
Using SDRAM Interface ............................................................... 2-4
Using Flash Memory ..................................................................... 2-5
Flash Memory Map ................................................................. 2-6
Flash General-Purpose IO ....................................................... 2-7
Configuring Flash Memory ..................................................... 2-9
Using LEDs and Push Buttons .................................................... 2-10
Using Audio ............................................................................... 2-11

ADSP-BF533 EZ-KIT Lite Evaluation System Manual vii
CONTENTS
Using Video ................................................................................ 2-12
Example Programs ...................................................................... 2-13
Using Background Telemetry Channel ......................................... 2-13
Using EZ-KIT Lite VisualDSP++ Interface .................................. 2-13
Trace Window ....................................................................... 2-14
Enabling Trace Buffer ........................................................ 2-14
Reading Trace Buffer Data ................................................ 2-15
Performance Monitor ............................................................ 2-15
Boot Load ............................................................................. 2-16
Target Options ...................................................................... 2-17
Reset Options ................................................................... 2-17
On Emulator Exit ............................................................. 2-17
Other Options .................................................................. 2-18
Restricted Software Breakpoints ............................................. 2-19
EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 3-2
External Bus Interface Unit ...................................................... 3-3
SPORT0 Audio Interface ......................................................... 3-4
SPI Interface ........................................................................... 3-4
Programmable Flags ................................................................. 3-4
PPI Interface ........................................................................... 3-5
Video Output Mode ........................................................... 3-7
Video Input Mode .............................................................. 3-7
UART Port .............................................................................. 3-8

CONTENTS
viii ADSP-BF533 EZ-KIT Lite Evaluation System Manual
Expansion Interface ................................................................. 3-8
JTAG Emulation Port ............................................................. 3-9
Jumper and DIP Switch Settings ................................................... 3-9
Boot Mode Select Jumpers (JP2–1) ........................................ 3-10
Core Voltage Source Select Jumper (JP3) ............................... 3-10
Test DIP Switches (SW2–1) .................................................. 3-11
Video Configuration Switch (SW3) ....................................... 3-11
Push Button Enable Switch (SW9) ........................................ 3-12
LEDs and Push Buttons .............................................................. 3-13
Programmable Flag Push Buttons (SW7–4) ............................ 3-13
Reset Push Button (SW8) ...................................................... 3-14
Power LED (LED1) .............................................................. 3-14
Reset LEDs (LED3–2) .......................................................... 3-14
User LEDs (LED9–4) ........................................................... 3-15
USB Monitor LED (LED11) ................................................. 3-15
Connectors ................................................................................. 3-16
Expansion Interface (J3–1) .................................................... 3-16
Audio (J5–4) ......................................................................... 3-17
Video (J8) ............................................................................. 3-17
Power (J9) ............................................................................ 3-17
FlashLINK (P1) .................................................................... 3-18
RS232 (P2) ........................................................................... 3-19
SPORT0 (P3) ....................................................................... 3-19
JTAG (P4) ............................................................................ 3-20

ADSP-BF533 EZ-KIT Lite Evaluation System Manual ix
CONTENTS
BILL OF MATERIALS
INDEX

CONTENTS
x ADSP-BF533 EZ-KIT Lite Evaluation System Manual

ADSP-BF533 EZ-KIT Lite Evaluation System Manual xi
PREFACE
Thank you for purchasing the ADSP-BF533 EZ-KIT Lite®, Analog
Devices (ADI) evaluation system for Blackfin®embedded media
processors.
The Blackfin processors are embedded processors that support a Media
Instruction Set Computing (MISC) architecture. This architecture is the
natural merging of RISC, media functions, and digital signal processing
(DSP) characteristics towards delivering signal processing performance in
a microprocessor-like environment.
The evaluation board is designed to be used in conjunction with the Visu-
alDSP++®development environment to test the capabilities of the
ADSP-BF533 Blackfin processors. The VisualDSP++ development envi-
ronment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C and ADSP-BF533 assembly
• Load, run, step, halt, and set breakpoints in application program
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-BF533 processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-BF533 processor and the

xii ADSP-BF533 EZ-KIT Lite Evaluation System Manual
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and DSP development tools, go to
http://www.analog.com/dsp/tools/.
ADSP-BF533 EZ-KIT Lite provides example programs to demonstrate
the capabilities of the evaluation board.
LThe VisualDSP++ license provided with this EZ-KIT Lite evalua-
tion system limits the size of a user program to 20 KB of internal
memory.
The board features:
• Analog Devices ADSP-BF533 processor
DPerformance to 756 MHz
D160-pin Mini-BGA package
D27 MHz CLKIN oscillator
• Synchronous Dynamic Read Access Memory (SDRAM)
DMT48LC16M16 –32 MB (16M x 16-bits)
• Flash Memory
D2 MB (512K x 16 x 2chips)
• Analog Audio Interface
DAD1836 – Analog Devices 96 kHz audio codec
D4 input RCA phono jacks (2 channels)
D6 output RCA phono jacks (3 channels)

ADSP-BF533 EZ-KIT Lite Evaluation System Manual xiii
Preface
• Analog Video Interface
DADV7183 video decoder w/ 3 input RCA phono jacks
DADV7171 video encoder w/ 3 output RCA phono jacks
• Universal Asynchronous Receiver/Transmitter (UART)
DADM3202 RS-232 line driver/receiver
DDB9 male connector
•LEDs
D10 LEDs: 1 power (green), 1 board reset (red), 1 USB (red),
6 general purpose (amber), and 1 USB monitor (amber)
• Push Buttons
D5 push buttons with debounce logic: 1 reset,
4 programmable flags
• Expansion Interface
DPPI, SPI, EBIU, Timers2-0, UART,
programmable flags, SPORT0, SPORT1
• Other Features
DJTAG ICE 14-pin header
The EZ-KIT Lite board has two Flash memories with a total of 2 MB of
memory. The Flash memories can be used to store user-specific boot code,
allowing the board to run as a stand-alone unit. For more information, see
“Using Flash Memory” on page 2-5. The board also has 32 MB of
SDRAM, which can be used by the user at runtime.

Purpose of This Manual
xiv ADSP-BF533 EZ-KIT Lite Evaluation System Manual
SPORT0 is interfaced with the AD1836 audio codec, allowing you to create
audio signal processing applications. SPORT0 is also attached to an
off-board connector to allow communication with other serial devices. For
information about SPORT0, see “SPORT0 Audio Interface” on page 3-4.
The Parallel Peripheral Interface (PPI) of the DSP is connected to both a
video encoder and video decoder, allowing you to create video signal pro-
cessing applications.
The UART of the DSP is connected to an RS232 Line Driver and a DB9
male connector, allowing you to interface with a PC or other serial device.
Additionally, the EZ-KIT Lite board provides access to most of the pro-
cessor’s peripheral ports. Access is provided in the form of a
three-connector expansion interface. For information about the expansion
interface, see “Expansion Interface” on page 3-8.
Purpose of This Manual
The ADSP-BF533 EZ-KIT Lite Evaluation System Manual provides
instructions for using the hardware and installing the software on your
PC. This manual provides guidelines for running your own code on the
ADSP-BF533 EZ-KIT Lite. The manual also describes the operation and
configuration of the evaluation board’s components. Finally, a schematic
and a bill of materials are provided as a reference for future ADSP-BF533
board designs.
Intended Audience
This manual is a user’s guide and reference to the ADSP-BF533 EZ-KIT
Lite evaluation system. Programmers who are familiar with the Analog
Devices Blackfin processor architecture, operation, and programming are
the primary audience for this manual.

ADSP-BF533 EZ-KIT Lite Evaluation System Manual xv
Preface
Programmers who are unfamiliar with Analog Devices Blackfin processors
can use this manual in conjunction with the ADSP-BF533 Processor Hard-
ware Reference and the Blackfin Processor Instruction Set Reference, which
describe the processor architecture and instruction set. Programmers who
are unfamiliar with VisualDSP++ should refer to the VisualDSP++ online
Help and the VisualDSP++ user’s or getting started guides. For the loca-
tions of these documents, refer to “Related Documents”.
Manual Contents
The manual consists of:
• Chapter 1, “Getting Started” on page 1-1
Provides software and hardware installation procedures, PC system
requirements, and basic board information.
• Chapter 2, “Getting Started” on page 1-1
Provides information on the EZ-KIT Lite from a programmer’s
perspective and provides an easy-to-access memory map.
• Chapter 3, “EZ-KIT Lite Hardware Reference” on page 3-1
Provides information on the hardware aspects of the evaluation
system.
• Appendix A, “Bill Of Materials” on page A-1
Provides a list of components used to manufacture the EZ-KIT
Lite board.

What’s New in This Manual
xvi ADSP-BF533 EZ-KIT Lite Evaluation System Manual
• Appendix B, “Schematics” on page B-1
Provides the resources to allow EZ-KIT Lite board-level debug-
ging or to use as a reference design.
This appendix is not part of the online Help. The online Help
viewers should go the PDF version of the ADSP-BF533 EZ-KIT
Lite Evaluation System Manual located in the Docs\EZ-KIT Lite
Manuals folder on the installation CD to see the schematics.
What’s New in This Manual
This revision of the ADSP-BF533 EZ-KIT Lite Evaluation System Manual
provides the updated schematics and information on the boot mode and
core voltage source selection jumpers.
Technical or Customer Support
You can reach DSP Tools Support in the following ways.
• Visit the DSP Development Tools website at
www.analog.com/technology/dsp/developmentTools/index.html
• Email questions to
[email protected]
• Phone questions to 1-800-ANALOGD
• Contact your ADI local sales office or authorized distributor

ADSP-BF533 EZ-KIT Lite Evaluation System Manual xvii
Preface
• Send questions by mail to
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
The ADSP-BF533 EZ-KIT Lite evaluation system supports ADSP-BF533
Blackfin Analog Devices embedded processors.
Product Information
You can obtain product information from the Analog Devices website,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our website provides infor-
mation about a broad range of products—analog integrated circuits,
amplifiers, converters, and digital signal processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices website that allows
customization of a webpage to display only the latest information on
products you are interested in. You can also choose to receive weekly email
notification containing updates to the webpages that meet your interests.
MyAnalog.com provides access to books, application notes, data sheets,
code examples, and more.

Product Information
xviii ADSP-BF533 EZ-KIT Lite Evaluation System Manual
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
email address.
DSP Product Information
For information on digital signal processors, visit our website at
www.analog.com/dsp, which provides access to technical publications, data
sheets, application notes, product overviews, and product announcements.
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• Email questions or requests for information to
[email protected]
• Fax questions or requests for information to 1-781-461-3010
(North America) or [phone] (Europe)
Related Documents
For information on product related development software, see the follow-
ing publications.
Table 1. Related DSP Publications
Title Description
ADSP-BF533 Embedded Processor Datasheet General functional description, pinout, and
timing.

ADSP-BF533 EZ-KIT Lite Evaluation System Manual xix
Preface
The listed documents can be found through online Help or in the Docs
folder of your VisualDSP++ installation. Most documents are available in
printed form.
LIf you plan to use the EZ-KIT Lite board in conjunction with a
JTAG emulator, refer to the documentation that accompanies the
emulator.
ADSP-BF533 Blackfin Processor Hardware Ref-
erence
Description of internal processor architecture
and all register functions.
Blackfin Processor Instruction Set Reference Description of all allowed processor assembly
instructions.
Table 2. Related VisualDSP++ Publications
Title Description
VisualDSP++ 3.5 User’s Guide for 16-Bit Proces-
sors
Detailed description of VisualDSP++ 3.5 fea-
tures and usage.
VisualDSP++ 3.5 Assembler and Preprocessor
Manual for Blackfin Processors
Description of the assembler function and
commands for Blackfin processors.
VisualDSP++ 3.5 C/C++ Complier and Library
Manual for Blackfin Processors
Description of the complier function and com-
mands for Blackfin processors
VisualDSP++ 3.5 Linker & Utilities Manual for
16-Bit Processors
Description of the linker function and com-
mands for 16-bit processors.
VisualDSP++ 3.5 Loader Manual for 16-Bit
Processors
Description of the loader/splitter function and
commands for 16-bit processors.
Table 1. Related DSP Publications (Cont’d)
Title Description

Product Information
xx ADSP-BF533 EZ-KIT Lite Evaluation System Manual
Online Documentation
Your software installation kit includes online Help as part of the Win-
dows®interface. These help files provide information about VisualDSP++
and the ADSP-BF533 EZ-KIT Lite evaluation system.
To view VisualDSP++ Help, click on the Help menu item or go to the
Windows task bar and select Start –>Programs –>Analog Devices–>Visu-
alDSP for 16-bit Processors –>VisualDSP++ Documentation.
To view ADSP-BF533 EZ-KIT Lite Help, which now is a part of the
VisualDSP++ Help system, go the Contents tab of the Help window and
select Manuals –>Hardware Tools –>EZ-KIT Lite. Evaluation Systems.
For more documentation, please go to
http://www.analog.com/technology/dsp/library.html.
Printed Manuals
For general questions regarding literature ordering, call the Literature
Center at 1-800-ANALOGD (1-800-262-5643) and follow the prompts.
VisualDSP++ Documentation Set
Printed copies of VisualDSP++ manuals may be purchased through Ana-
log Devices Customer Service at 1-781-329-4700; ask for a Customer
Service representative. The manuals can be purchased only as a kit. For
additional information, call 1-603-883-2430.
If you do not have an account with Analog Devices, you will be referred to
Analog Devices distributors. To get information on our distributors, log
onto www.analog.com/salesdir/continent.asp.