Analog devices Rapid-niek-v0004 User manual

RAPID-NIEK-V0004 User Guide

UG-1204

One Technology Way •P. O. Box 9106 •Norwood, MA 02062-9106, U.S.A. •Tel: 781.329.4700 •Fax: 781.461.3113 •

www.analog.com

RapID Platform Network Interface

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 7

EVALUATION KIT CONTENTS

Network interface baseboard

UART personality module

Parallel interface personality module

Ethernet personality module

Power supply with outlet adapters

Ethernet cable

USB cable

Innovasic developer portal information card

DOCUMENTS NEEDED

Protocol specific user guide

ADDITIONAL HARDWARE REQUIRED

RapID-NI-V2007, RapID-NI-V2008, RapID-NI-V2009, RapID-

NI-V2010, RapID-NI-V2011, or RapID-NI-V2012 module

ADDITIONAL SOFTWARE REQUIRED

NI_TEST_IO host processor simulator, available for download

from the Developer Portal

GENERAL DESCRIPTION

The RapID™ Platform network interface solutions are pretested,

industrial network interfaces that manage the industrial

protocol and network traffic. The unified interface of the

module allows a single host interface hardware, and the

software design supports PROFINET®, PROFINET IRT,

PROFIBUS®, EtherNet/IP, EtherNet/IP with device level ring

(DLR), EtherCAT, and ModbusTCP. Choose the type of

network interface to support the required industrial protocols.

The unified interface ensures that the host processor hardware

or software interface does not need to change, even when the

user switches or updates protocols. The network interface

connects to a host processor via a UART, 16-bit parallel

interface, or Ethernet cable.

The evaluation kit provides a quick assessment for interfacing a

host processor to the network interface module (sold separately).

When the host side communication is established, use third

party PC-based tools or vendor specific programmable logic

controllers (PLC) to evaluate the communication. The commu-

nication path between the host processor and a PLC can be

completely verified before integrating the network interface into

the end field device.

The RAPID-NIEK-V0004 evaluation kit provides an end to end

evaluation of the communication path from the host processor

to the PLC. This user guide describes how to use the evaluation

kit to set up and run a host simulator example (see the corre-

sponding protocol specific user guide for full details). The

application example demonstrates the host communication

example that ultimately leads to an end to end communication

from a host processor to a PLC. For the example described in

this user guide, the host processor is a PC and communicates to

the network interface via USB. Communication to the PLC is is

described on a protocol by protocol basis in the protocol specific

user guide.

After running the application example, the user can refer to the

protocol specific quickstart guide for an example of the network

communication. The evaluation kit and protocol specific user

guide must be used in conjuction with the Design Integration

Guide to develop field device products, available for download

from the Developer Portal.

Figure 2 shows an overview of the evaluation and development

process. For full details on the completion of a field device design

using the network interface, see the Design Integration Guide.

UG-1204 RAPID-NIEK-V0004 User Guide

Rev. 0 | Page 2 of 7

TABLE OF CONTENTS

Evaluation Kit Contents................................................................... 1

Documents Needed.......................................................................... 1

Additional Hardware Required ...................................................... 1

Additional Software Required ........................................................ 1

General Description ......................................................................... 1

Revision History ............................................................................... 2

Evaluation Kit Overview.................................................................. 3

Evaluation Board Hardware.............................................................4

Electrostatic Discharge (ESD) and Power Supply

Considerations...............................................................................4

Power Supply and Grounding .....................................................4

Evaluation Hardware Setup .........................................................4

Evaluation Board Schematics...........................................................6

REVISION HISTORY

2/2019—Revision 0:Initial Version

RAPID-NIEK-V0004 User Guide UG-1204

Rev. 0 | Page 3 of 7

EVALUATION KIT OVERVIEW

Figure 1 and Figure 2 show the contents of the evaluation kit and an overview of the evaluation development process, respectively.

Figure 1. Evaluation Kit Contents

Figure 2. Evaluation and Development Overview

16284-001

5. CONFIGURE PRODUCTION HARDWARE

A) MODULE

PROGRAM

HOST

PROCESSOR

FLASH

B) EMBEDDED DESIGN

2. SET UP AND RUN EXAMPLE

QUICK START

GUIDE

1. ORDER NETWORK INTERFACE

EVALUATION KIT AND MODULE.

KIT ORDER NUMBER: RAPID-NIEK-V0004

(MODULE SOLD SEPARATELY)

CONFIGURE

INTERFACE

SOURCE

LIBRARY

PLC

3. INTEGRATE UNIFIED INTERFACE ON HOST

4. INTEGRATE HARDWARE

MODULE

EMBEDDED DESIGN

HOST

DEVELOPMENT

ENVIRONMENT

16284-002

UG-1204 RAPID-NIEK-V0004 User Guide

Rev. 0 | Page 4 of 7

EVALUATION BOARD HARDWARE

This section describes how to connect the hardware provided in

the evaluation kit. The following steps use a PC with USB as a

host processor and a PLC with an EtherNet/IP industrial Ethernet

interface. See the Developer Portal page on the Analog Devices,

Inc., website for a full list of protocol specific user guides.

ELECTROSTATIC DISCHARGE (ESD) AND POWER

SUPPLY CONSIDERATIONS

Electrostatic Sensitive Device

Handle the hardware in this evaluation kit in accordance with

proper ESD device handling techniques. Use a grounding wrist

strap when using this evaluation board prevent accidental

damage to the hardware.

POWER SUPPLY AND GROUNDING

A wall adapter power supply is included with the evaluation

boards. This supply is 12 V, 1 A, and attaches to the power

supply barrel connector. A screw terminal to attaches a lab

benchtop power supply. For either type of power supply

connection, the input voltage to the board must be in the 9 V to

33 V range.

EVALUATION HARDWARE SETUP

The following steps detail the hardware setup process. Figure 5

shows the completed hardware setup with proper baseboard

and module connections. The evaluation kit comes with the

jumpers installed and there is no need to set any switches. The

UART interface, parallel interface, or Ethernet interface

personality modules are not used in this setup procedure.

1. Connect the module to the baseboard as shown in Figure 5.

2. Connect the USB cable from the PC to the baseboard, as

shown in Figure 3. This step creates two virtual COM ports

on the PC that are used later in the application example.

Figure 3. USB Cable Connection

3. Connect the power cable provided in the kit to the power

port, as shown in Figure 4. Plug the other end of the power

cord into a wall socket.

Figure 4. Power Cable Connection

Figure 5. Module and Baseboard Connection

16284-004

16284-005

16284-003

RAPID-NIEK-V0004 User Guide UG-1204

Rev. 0 | Page 5 of 7

4. Connect one end of the provided Ethernet cable in the kit

to either of the RJ45 jacks on the network interface module,

as shown in Figure 6. Connect the other end of the Ethernet

cable to the PLC, and then connect the PLC to the PC via

the Ethernet cable.

Figure 6. Ethernet Cable Connection

5. Apply power to the module by turning the network

interface module baseboard power switch to the on

position, as shown in Figure 7.

Figure 7. Power-On Switch Location

16284-006

16284-007

UG-1204 RAPID-NIEK-V0004 User Guide

Rev. 0 | Page 6 of 7

EVALUATION BOARD SCHEMATICS

Figure 8. Network Interface Baseboard Schematic

Figure 9. Network Interface Connectors Schematic

PJ-102AH

R-723.3 D

GND

DNP

GND

1µF

GND

+3.3V

MAX6817

GND

10kΩ

+3.3V

GND

GRN

470Ω

RED 470Ω

GND

+3.3V

GND

ZX62-AB-5PA_MICRO-USB

GND

0.1µF

50mΩ 1A

1kΩ

GND

0.1µF

GND

+3.3V

GND

GRN RX

470Ω

RED TX

RED

470Ω

+3.3V

691101710003

GND

CL2N8-G

470Ω

200Ω

SMBJ28CA

10kΩ

+3.3V

CD603-B0034

J1 1

VIN

VOUT 9

GND

VIN

VOUT 10

VOUT 11

GND

ON/OFF*

VO_ADJ 12

IN1

IN2

OUT1 6

OUT2 4

VCC 5

GND

3S2

LED1

LED4

LED5

X1C

X1S

VCCIO

VCC

USBDM

USBDP

_RESET

OSCI

OSCO

3.3VOUT

TXD 1

RXD 5

_RTS 3

_CTS 11

_DTR 2

_DSR 9

_DCD 10

_RI 6

CBUS0 23

CBUS1 22

CBUS2 13

CBUS3 14

CBUS4 12

AGND

GND

TEST

FT232RL

FB1

GND +3.3V

U5G2

U5G1

GND +3.3V

U4G2

1U4G1

4.7µF

47µF

C7 100µF

C10

LED2

LED3

LED6

R10

TP1

R11

R12

MANUAL_RESET_N

N$10

BOOTLOAD_EN_N

VCCIO

POWER SUPPLY

VIN +9V TO 24V DC

RESET

BOOTLOAD SPARE GND CONNECTORS

+3.3 VALID

POWER IN VALID

USB

FT232RL

16284-008

NI_HDR_GND

NI_HDR_GNDNI_HDR_GND

+3.3V

GND

+3.3V

NI_HDRPM_HEADER_32NI_HDRPM_HEADER_32

+3.3V

GND

GNDA

J8GNDA

A10

A11

A12

A13

A14

A15

A16

J8A

B10

B11

B12

B13

B14

B15

B16

J8B

C10

C11

C12

C13

C14

C15

C16

J8C

D10

D11

D12

D13

D14

D15

D16

J8D

A10

A11

A12

A13

A14

A15

A16

JP1A

B10

B11

B12

B13

B14

B15

B16

JP1B

C10

C11

C12

C13

C14

C15

C16

JP1C

D10

D11

D12

D13

D14

D15

D16

JP1D

D15

D15 D14D14 D13D13 D112D112 D11

D11 D10D10 D9D9 D8

D8 D7D7 D6

D6 D5

D5 D4D4 D3D3 D2D2 D1D1

C2C2 C3C3 C4

A8A8

A6 A5A5 A4A4 A3

A1A1

C6C6 A7

A7 C7C7

B10

B4 B3B3

B5 B6

B6 B7

C8C8

C5C5

RESET_OUT_NRESET_OUT_N

C11

B11B11

C12C12 C13

C13 C14

C14 C15C15

B12B12 B13B13 B14B14 B15B15

BOOTLOAD_EN_NBOOTLOAD_EN_N

16284-009

MANUAL_RESET_N

A2A2

A10

A10 A11A11 A12

A12 A13

A13 A14A14 A15A15 A16

A16 C16C16

D16

GNDA GNDA

NETWORK INTERFACE BASE BOARD

NETWORK INTERFACE

PM CONNECTORS NETWORK MODULE

CONNECTORS

RAPID-NIEK-V0004 User Guide UG-1204

Rev. 0 | Page 7 of 7

NOTES

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions

set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you

have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.

(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,

temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided

for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional

limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term

“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including

ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may

not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to

promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any

occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.

Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice

to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO

WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED

TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL

PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF

THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITEDTO THE

AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable

United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of

Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby

submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.