Ancona PA-TM-WF01 User manual
LED Light.
Switch Paddle.
Ground
Green
White
Neutral
Red
Load (to light xture)
Black
Hot (from breaker)
Wireless Home Automation Control Device
Interchangeable Face Cover On/Off Switch
INSTALLATION INTRUCTIONS
Specifications
Voltage
Incandescent
Electronic Ballast
Standard Ballast
Resistive
Motor
Operating Temperature
Wire Strip Length
Supply Connection
Screw Torque
Protocol
Wireless Type
120VAC, 60Hz
1000W
5A
1200VA
1800W(15A)
1/2 HP
32°F~104°F (0°C~40°C)
16 mm (5/8 in.)
14 AWG wires, suitable for at least 90°C
20 lbf-in
IEEE 802.11b/g/n
2.4GHz (Type 1.B action, operating control)
Features
Perfect replacement for regular wall switch, 120VAC, 15Amp.
Manual and remote ON/OFF control of any connected lighting and other
electrical load.
You can turn your devices on or off at any time or anywhere with internet
connection, using the free Tuya App on your smartphone.
Interchangeable color face plate.
Indoor use only.
The PA-TM-WF01 ON/OFF Switch is a perfect wireless manual and remote
on/off control, replacing regular wall switch, controlling incandescent, LED,
uorescent, ballast and so on.
WARNINGS AND CAUTIONS:
Be sure to read the instructions carefully before installation, as the
manufacturer will not be responsible for any product damage
caused by not following the instructions.
1. Wet hands are strictly prohibited.
2. Must work strictly according to the rated load.
3. Do not continue to work after self-disassembly of any nature and
damage of external forces.
Installation
1.
2.
3.
4.
5.
WARNING: To avoid fire, shock, or death. High Voltage - Turn off power
at circuit breaker or fuse and test that power is off before wiring.
Remove wall plate and existing switch mounting screws.
Carefully remove the existing switch from the switch box.
Disconnect the wiring from the existing switch.
Connect the switch as shown in the wiring diagram: Black lead to hot wire,
white lead to neutral wire, red lead to load wire, green lead to ground wire.
Wiring diagram
White (Neutral)
Green (Ground)
Black (Line/Hot)
Red (Load)
PA-TM-WF01
6.
7.
8.
9.
10.
Check connections to make sure they are tight and no bare conductors are
exposed.
Insert the PA-TM-WF-01 switch into the standard outlet box carefully.
Secure the switch to the box using the supplied screws.
Attach the wall plate.
Restore power at the circuit breaker and test the system.
Operation
— 1 — — 2 — — 3 —
To replace the face
cover, just use a
at screwdriver to
pry-off the
interchangeable
plate.
Manual Control
To turn the connected lighting ON: Tap the top of the switch paddle.
To turn the connected lighting OFF: Tap the bottom of the switch paddle.
The switch paddle allows the user to turn ON/OFF the connected lighting.
Please Note: After a power failure, the on/off switch returns to OFF state.
Tuya Smart App Control
1.
Download Tuya Smart app from the App Store or Google Play.
2.
Connect mobile device to your 2.4GHz Wi-Fi network. Please note this
Smart switch can only be connected to 2.4GHz network.
a. Click the button “+”.b. Select "Wi-Fi Switch". c. Click the bottom button.
d. Enter your Wi-Fi password. e. Connect. f. Finished.
3.
Launch Tuya and follow the in-app instructions to connect the Wi-Fi switch
to your network.
MAPA-TM-WF-01-03
Operation and LED Indication
Quick blinking green: Connecting to the network.
Slow blinking green: AP mode.
Green bright after 2 seconds off: Connected to the network.
Solid green: Network working normally or in standby mode.
Solid blue: The Wi-Fi switch is switched on.
Off: The Wi-Fi switch is switched off.
Federal Communication Commission Interference
Statement
FCC Compliance Statement
— 4 — — 5 — — 6 —
Warranty Information
AMS warrants its products to be free of defects in materials and workmanship
for a period of one (1) year. There are no obligations or liabilities on the part of
AMS for consequential damages arising out of or in connection with the use
or performance of this product or other indirect damages with respect to loss
of property, revenue, or prot, or cost of removal, installation or reinstallation.
Limited Product Warranty shall be automatically void if: (i) any repair,
alteration, modication, customization, disassembling, addition or any other
work is performed on the Product by any person not authorized by AMS to do
so; (ii) any alleged material defect, including deterioration or wear, is a result
of failure to observe the manufacturer’s instructions or guidelines, abuse,
misuse, improper operation, care or maintenance, unusual physical or
electrical stress and/or power surges, brown-out, chemical abrasion or
improper chemical or environmental conditions, leaking, re, lightning, force
majeure or superior force, accident, error, negligence, or is a result of use for
nondomestic or non-residential purposes or for any purpose other than the
Product’s intended purpose; (iii) the Product is operated in conjunction with
accessories, other products, ancillaries or peripheral equipment or
substances that have not been previously approved in writing or validated by
AMS; or (iv) Purchaser fails to comply with the Warranty Claim Procedure.
20201211
4.
Once the device is added, Wi-Fi switch can be opened, closed, set
countdown and timer.
Please Note
1.
2.
While adding device, you must correctly select the router's Wi-Fi device
name and ll in the correct Wi-Fi password, otherwise the device will not be
added successfully.
This Wi-Fi switch can only be paired with one phone device. If you want
multiple phones to control the Wi-Fi switch, click the "prole" then choose
"Device Sharing".
3.
When the device fails to add the App, please try to enter the AP mode.
Before entering the AP mode, please press the top or bottom button 5 times
continuously, then press and hold at the sixth time for 5 seconds, then
release. The LED indicator is green and slowly blinks.
This equipment has been tested and found to comply with the limits for a class B
Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment uses, generates and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1.
2.
This device may not cause interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
RF Exposure: A distance of 20 cm shall be maintained between the antenna and
users, and the transmitter module may not be co-located with any other
transmitter or antenna.
Non-modification Statement
Any changes or modications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
MAPA-TM-WF-01-03
www.anconahome.com
