AND AD-4412-CW User manual

Weighing Indicator
1WMPD4003953A

WARNING DEFINITIONS
The warnings described in this manual have the following meanings:
WARNING A potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
A
potentially hazardous situation which, if not avoided, may result
in minor or moderate injury or damage to the instrument.
This symbol indicates caution against electrical shock. Do not
touch the part where the symbol is placed.
This symbol indicates the ground terminal.
This symbol indicates that an operation is prohibited.
Note Information or cautions to use the device correctly.
2019 A&D Company, Limited. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, or
translated into any language in any form by any means without the written
permission of A&D Company, Limited.
The contents of this manual and the specifications of the instrument covered by
this manual are subject to change for improvement without notice.
Windows is registered trademarks of Microsoft Corporation.
Modbus protocol is is registered trademarks of Modicon Inc.
Other trademarks and trade names are those of their respective owners.

AD-4412-CW, AD-4413-CW 1
Contents
1. Introduction ..................................................................................................................................... 7
1.1. Features ...................................................................................................................................... 7
1.2. Safety Precautions ..................................................................................................................... 8
1.3. Compliance................................................................................................................................. 9
2. Parts Names................................................................................................................................. 10
2.1. Front Panel................................................................................................................................ 10
2.2. Rear Panel .................................................................................................................................11
3. Installing the Weighing Indicator.................................................................................................. 12
3.1. USB Flash Drive ....................................................................................................................... 12
3.1.1. Connecting USB Flash Drive ............................................................................................... 12
3.1.2. Removing USB Flash Drive ................................................................................................. 12
3.2. Installing Option board.............................................................................................................. 13
3.3. Mounting the Weighing Indicator on Panel............................................................................. 13
3.3.1. Panel Mount Kit ( AD-4412-10 )......................................................................................... 14
3.3.2. Attachment Kit ( AD-4412-11 ) for Indicator Stand ( AD-4402-25 ) ............................... 15
3.4. Connecting Load Cell Cables.................................................................................................. 16
3.5. Connecting Power Lines.......................................................................................................... 17
4. Operation Window ....................................................................................................................... 18
4.1. Icon ............................................................................................................................................ 18
4.2. Numerical Input......................................................................................................................... 18
4.3. Pull Down Menu ....................................................................................................................... 19
4.4. IP Address................................................................................................................................. 19
4.5. Alphanumeric Input .................................................................................................................. 20
4.6. Password Input......................................................................................................................... 20
5. Basic Operations.......................................................................................................................... 21
5.1. Operation Outline...................................................................................................................... 21
5.2. Turning on the Power ............................................................................................................... 22
5.3. Turning off the Power ............................................................................................................... 22
5.4. Weighing Operations................................................................................................................ 23
5.4.1. Changing the Indication of weighing Value ......................................................................... 23
5.4.2. Adjusting Zero point (to Display Zero) ................................................................................. 24
5.4.3. Starting and Stopping the Weighing Operation .................................................................. 24
5.5. Managing User level for Logging in......................................................................................... 25
5.5.1. Management level of User ................................................................................................... 25
5.5.2. Changing User...................................................................................................................... 26
5.5.3. Registering User ................................................................................................................... 27
5.5.4. Changing User Information .................................................................................................. 28
5.5.5. Deleting User......................................................................................................................... 29
5.6. Selection of Products and Detection Function........................................................................ 31
5.6.1. Registering Products ............................................................................................................ 31
5.6.2. Settings of Threshold Values ( Target, HiHi Limit, Hi Limit, Lo Limit, LoLo Limit )............. 33
5.6.3. Setting Product Length and Velocity.................................................................................... 34
5.6.4. Setting the Digital Output (DO) ............................................................................................ 35
5.6.5. Setting the Delay Time and Holding Time........................................................................... 36

2 AD-4412-CW, AD-4413-CW
5.6.6. DO Test Function .................................................................................................................. 37
5.6.7. Setting a Tare Value.............................................................................................................. 37
5.6.8. The Selection of Weighing Product ..................................................................................... 38
5.6.9. The Registration of Product Image...................................................................................... 38
5.6.10. Creating a Copy of Product Settings ................................................................................... 39
5.6.11. Deleting Product Settings..................................................................................................... 40
5.7. Summary of Weighing Result.................................................................................................. 41
5.7.1. Weighing History ................................................................................................................... 41
5.7.2. All Summary.......................................................................................................................... 42
5.7.3. OK Summary ........................................................................................................................ 42
5.7.4. Number of Samples Summary ............................................................................................ 43
5.7.5. Number of OK Samples Summary ..................................................................................... 44
5.7.6. Histogram .............................................................................................................................. 45
5.7.7. Control Chart .................................................................................................................. 46
5.7.8. Control Chart.................................................................................................................... 47
6. Adjustment Operations for the Indicator ..................................................................................... 48
6.1. Calibrating the Indicator using a Weight.................................................................................. 48
6.2. Settings for Date and Time ...................................................................................................... 50
6.3. Setting up LAN interface .......................................................................................................... 51
7. Output of Weighing Results and Summary................................................................................ 52
7.1. Output to USB Flash Drive....................................................................................................... 52
7.1.1. Output of Weighing History .................................................................................................. 52
7.1.2. Example: Output File of Weighing History .......................................................................... 53
7.1.3. PDF output of Histogram, Control Chart and Summary .................................................... 54
7.2. Output to the Postscript Printer................................................................................................ 55
7.2.1. Output to Postscript Printer .................................................................................................. 55
7.2.2. Printing Sample of Histogram .............................................................................................. 56
7.2.3. Print Sample of Control Chart .............................................................................................. 57
7.2.4. Print Sample of Summary .................................................................................................... 58
7.3. Output to the Dump Printer...................................................................................................... 59
7.3.1. Output to the Dump Printer .................................................................................................. 59
7.3.2. Print Samples........................................................................................................................ 60
8. Peripherals.................................................................................................................................... 64
8.1. Format of USB Flash Drive...................................................................................................... 64
8.2. Connecting the LAN interface.................................................................................................. 65
8.2.1. How to Connect to Network Using Wired LAN................................................................... 65
8.2.2. How to Connect to Network Using Wireless LAN .............................................................. 65
8.3. Connecting the PostScript Printer ........................................................................................... 66
8.4. Remote Monitor........................................................................................................................ 66
8.5. Replacing Product Using Serial Communication ................................................................... 67
9. The Details of Settings................................................................................................................. 68
9.1. Product Name and Product Code........................................................................................... 72
9.1.1. Product Name ....................................................................................................................... 72
9.1.2. Product Code ........................................................................................................................ 72
9.2. Detect Basis .............................................................................................................................. 72
9.2.1. Reject Stage ( Count of Separation )................................................................................... 72

AD-4412-CW, AD-4413-CW 3
9.2.2. Target ..................................................................................................................................... 72
9.2.3. HiHi Limit................................................................................................................................ 72
9.2.4. Hi Limit ................................................................................................................................... 72
9.2.5. Lo Limit .................................................................................................................................. 73
9.2.6. LoLo Limit .............................................................................................................................. 73
9.2.7. Over Weight Exception......................................................................................................... 73
9.2.8. Consecutive Fail Stop........................................................................................................... 73
9.2.9. Consecutive Fail Num .......................................................................................................... 73
9.3. Detect Parameter ..................................................................................................................... 74
9.3.1. Product Length...................................................................................................................... 74
9.3.2. Speed .................................................................................................................................... 74
9.3.3. Weighing Mode ..................................................................................................................... 74
9.3.4. Conveyor Stop Timer............................................................................................................ 74
9.3.5. Product Detection ................................................................................................................. 75
9.3.6. Near Zero Range.................................................................................................................. 75
9.3.7. Auto Mode ( to Set Parameters).......................................................................................... 75
9.4. DO Map (Digital Output Map)............................................................................................... 76
9.4.1. DO Map Reference .............................................................................................................. 76
9.4.2. Output Definition of DO Map................................................................................................ 76
9.5. Control I/O (Part of Digital Output)........................................................................................ 79
9.5.1. DO Behavior.......................................................................................................................... 79
9.5.2. Delay Time ............................................................................................................................ 79
9.5.3. Hold Time .............................................................................................................................. 79
9.5.4. Polarity ................................................................................................................................... 79
9.6. Statistics .................................................................................................................................... 80
9.6.1. Num of Samples ................................................................................................................... 80
9.6.2. Sub Samples......................................................................................................................... 80
9.6.3. ........................................................................................................................................... 80
9.6.4. ........................................................................................................................................... 80
9.6.5. Width of Section .................................................................................................................... 80
9.7. Ta r e ............................................................................................................................................ 81
9.8. Auto Zero................................................................................................................................... 81
9.8.1. Auto Zero Range .................................................................................................................. 81
9.8.2. Dead Zone Timer.................................................................................................................. 81
9.8.3. Observation Timer................................................................................................................. 82
9.8.4. Averaging Time ..................................................................................................................... 82
9.8.5. Auto Zero Sample................................................................................................................. 82
9.8.6. Coe (Coefficient)................................................................................................................. 82
9.9. D. Comp. Value......................................................................................................................... 82
9.10. Feedback Control (FC)............................................................................................................. 83
9.10.1. Feedback Control Target ...................................................................................................... 84
9.10.2. Feedback Control Range ..................................................................................................... 84
9.10.3. Feedback Control Step : [g/sec.] or [sec./g] ........................................................................ 84
9.10.4. Feedback Control Sample ................................................................................................... 84
9.10.5. Feedback Control Waiting Time........................................................................................... 84
9.11. Step Control .............................................................................................................................. 85
9.11.1. Control Target........................................................................................................................ 85
9.11.2. Zone 1 to 4 of 10 Stage Control........................................................................................... 86

4 AD-4412-CW, AD-4413-CW
9.11.3. 10 C Sample ......................................................................................................................... 86
9.11.4. 10 C Wait Time...................................................................................................................... 86
9.12. Weighing ................................................................................................................................... 87
9.12.1. Unit......................................................................................................................................... 87
9.12.2. Decimal Point........................................................................................................................ 87
9.12.3. Division .................................................................................................................................. 87
9.12.4. Capacity................................................................................................................................. 87
9.12.5. Digital Filter ............................................................................................................................ 87
9.12.6. Zero Point Range.................................................................................................................. 87
9.12.7. Power on Auto Zero Range.................................................................................................. 87
9.12.8. Zero Tracking Time ............................................................................................................... 88
9.12.9. Zero Tracking Weight............................................................................................................ 88
9.12.10. Stability Time ......................................................................................................................... 88
9.12.11. Stability Weight...................................................................................................................... 88
9.13. Cal (Calibration) ..................................................................................................................... 89
9.13.1. Weight.................................................................................................................................... 89
9.13.2. Zero Point .............................................................................................................................. 89
9.13.3. Span....................................................................................................................................... 89
9.14. Main Unit ................................................................................................................................... 90
9.14.1. Identification Name ............................................................................................................... 90
9.14.2. Start up User Level ............................................................................................................... 90
9.14.3. Conveyor Length .................................................................................................................. 90
9.14.4. Unsplit Range........................................................................................................................ 90
9.14.5. Conveyor Mode .................................................................................................................... 90
9.14.6. Connect Device Priority ........................................................................................................ 90
9.14.7. Curb Chattering..................................................................................................................... 91
9.14.8. Photo Eye Sensor Polarity ................................................................................................... 91
9.14.9. Photo Eye Sensor Timeout .................................................................................................. 91
9.14.10. Random Check (To input data previously).......................................................................... 91
9.15. Display....................................................................................................................................... 92
9.15.1. Language .............................................................................................................................. 92
9.15.2. Display Mode ........................................................................................................................ 92
9.15.3. Negative Weight.................................................................................................................... 92
9.15.4. Display Data .......................................................................................................................... 92
9.15.5. Standby Mode....................................................................................................................... 92
9.15.6. Brightness.............................................................................................................................. 92
9.16. Connection................................................................................................................................ 92
9.16.1. Printer IP Address ................................................................................................................. 92
9.17. DI Map (Digital Input Map) .................................................................................................... 93
9.18. Control I/O (Part of Digital Input)........................................................................................... 93
9.18.1. Input Trigger .......................................................................................................................... 94
9.18.2. Configuration ......................................................................................................................... 96
9.18.3. Delay Time ............................................................................................................................ 99
9.18.4. Chattering .............................................................................................................................. 99
9.19. DI Indicator .............................................................................................................................. 100
9.20. Analog Out .............................................................................................................................. 101
9.20.1. Data Types .......................................................................................................................... 101
9.20.2. Output Format..................................................................................................................... 101

AD-4412-CW, AD-4413-CW 5
9.20.3. Low Voltage Standard ........................................................................................................ 101
9.20.4. High Voltage Standard........................................................................................................ 101
9.20.5. Low Voltage Output ............................................................................................................ 101
9.20.6.High Voltage Output............................................................................................................ 101
9.20.7. Low Current Standard ........................................................................................................ 101
9.20.8. High Current Standard........................................................................................................ 101
9.20.9. Low Current Output ............................................................................................................ 101
9.20.10. High Current Output............................................................................................................ 101
9.21. Device...................................................................................................................................... 102
9.21.1. Model Name........................................................................................................................ 102
9.21.2. Serial Number ..................................................................................................................... 102
9.21.3. GUI Software Version ......................................................................................................... 102
9.21.4. Weighing Software Version................................................................................................ 102
9.21.5. Option Port 1 and 2............................................................................................................. 102
9.22. Date / Time.............................................................................................................................. 102
9.22.1. Date Set............................................................................................................................... 102
9.22.2. Time Set .............................................................................................................................. 102
9.23. USB Flash Drive ..................................................................................................................... 102
9.23.1. USB Operation History ....................................................................................................... 102
9.23.2. USB Weighing History........................................................................................................ 102
9.24. Modbus ................................................................................................................................... 103
9.24.1. Modbus................................................................................................................................ 103
9.24.2. Slave Address ..................................................................................................................... 103
9.25. Output Format......................................................................................................................... 104
9.26. RS-232C ................................................................................................................................ 106
9.26.1. RS-232C Port..................................................................................................................... 106
9.26.2. Output Mode ....................................................................................................................... 106
9.26.3. Baud Rate ........................................................................................................................... 106
9.26.4. Parity.................................................................................................................................... 106
9.26.5. Stop Bit ................................................................................................................................ 106
9.26.6. Data Bit ................................................................................................................................ 107
9.27. RS-485 ................................................................................................................................... 107
9.27.1. RS-485 Port ....................................................................................................................... 107
9.27.2. Output Mode ....................................................................................................................... 107
9.27.3. Baud Rate ........................................................................................................................... 107
9.27.4. Parity.................................................................................................................................... 107
9.27.5. Stop Bit ................................................................................................................................ 107
9.27.6. Data Bit ................................................................................................................................ 107
9.28. LAN.......................................................................................................................................... 108
9.28.1. CL IP Address ..................................................................................................................... 108
9.28.2. CL Subnet Mask ................................................................................................................. 108
9.28.3. CL Default Gateway............................................................................................................ 108
9.28.4. WL Port ................................................................................................................................ 108
9.28.5. WL IP Address..................................................................................................................... 108
9.28.6. WL Password...................................................................................................................... 108
9.29. Monitor..................................................................................................................................... 109
9.29.1. RS-232C............................................................................................................................. 109
9.29.2. RS-485 ............................................................................................................................... 110

6 AD-4412-CW, AD-4413-CW
9.29.3. Control I/O ........................................................................................................................... 110
9.29.4. OP-02 Relay Output ...........................................................................................................111
9.29.5. OP-05 Parallel I/O...............................................................................................................111
9.29.6. OP-07 Analog Output ........................................................................................................ 112
10. Modbus Communication ........................................................................................................... 113
10.1. Using Modbus RTU................................................................................................................ 114
10.2. Using Modbus TCP................................................................................................................ 114
10.3. Communication Command of Modbus................................................................................. 115
10.3.1. Example of Reading Input Register................................................................................... 115
10.3.2. Example of Writing Holding Register................................................................................. 116
10.3.3. Example of Exception Response ...................................................................................... 117
10.4. Reference Number................................................................................................................. 118
10.5. Address ................................................................................................................................... 118
10.6. Communication Command of Modbus TCP........................................................................ 142
10.6.1. Protocol Layout ................................................................................................................... 142
10.6.2. Example of Reading Input Register................................................................................... 142
11. Interface ...................................................................................................................................... 143
11.1. Control I/O............................................................................................................................... 143
11.1.1. Connection of Control I/O................................................................................................... 143
11.2. RS-232C ................................................................................................................................ 144
11.2.1. Connection of RS-232C .................................................................................................... 144
11.3. RS-485 ................................................................................................................................... 145
11.3.1. Connection of RS-485....................................................................................................... 145
11.4. Photo Eye Sensor .................................................................................................................. 146
11.4.1. Connection of Photo Eye Sensor ...................................................................................... 146
11.5. OP-02 Relay Output.............................................................................................................. 146
11.6. OP-05 Parallel Input / Output................................................................................................ 148
11.7. OP-07 Analog Output............................................................................................................ 150
11.7.1. The Way to Set Output Current ......................................................................................... 151
11.8. OP-17 Additional Analog Output Module............................................................................. 151
12. Maintenance............................................................................................................................... 152
12.1. Error Messages of Indicator................................................................................................... 152
12.1.1. Error Message Table........................................................................................................... 152
12.2. Backup of System Data ......................................................................................................... 153
12.3. Restoring System Data .......................................................................................................... 154
12.4. Initialization to Factory Settings.............................................................................................. 156
13. Specifications.............................................................................................................................. 157
13.1. Dimensions ............................................................................................................................. 158
13.1.1. AD-4412-CW .................................................................................................................... 158
13.1.2. AD-4413-CW .................................................................................................................... 159

AD-4412-CW, AD-4413-CW 7
1.
Introduction
1.1.
Features
Note
This instruction manual is described both weighing indicators of the AD-4412-CW and AD-
4413-CW. Explanation of common part in this manual expediently uses the AD-4412-CW.
Therefor if you use the AD-4413-CW, read and replace product name appropriately.
The AD-4412-CW and AD-4413-CW are the indicator designed for classifying the weighing
product on conveyor.
Stainless steel is used to the front panel of the AD-4413-CW.
Display Unit
The indicator equips 7-inch sensitive touch screen considered with operability.
The indicator realizes easy readability and operability using the touch screen.
Dustproof & waterproof structure
The indicator equips waterproof construction complying with IP65 when mounting on panel.
Functions
The indicator can store 1000 products (100 products for each 10 group) in maximum.
The indicator can read picture from USB flash drive and display it on touch screen.
User data can be stored, classified and managed properly using management level.
Therefore, operator can perform with safety operation of weighing system.
The indicator can perform serial communication and communicate with peripherals to support
modbus using TCP/IP communication and no program.
Output & input Interface
General input, rejecter output, alarm output, RS-232C / RS-485 input / output and TCP/IP are
equipped as standard model.

8 AD-4412-CW, AD-4413-CW
1.2.
Safety Precautions
Read the following precautions to use the indicator safely before use surely.
Caution
Hazard of rotating object
Keep hands and fingers away from the rotating part while the indicator is running.
If product has stayed on conveyor, fell over or spilled, stop the indicator immediately, turn the
power off and take necessary actions.
Hazard of electrical shock
Be sure to turn the power off before removing the display cover or control box cover for
inspection.
Keep the power turned off during the inspection.
Turn the power on after the installation has been complete.
Precautions for installation
Install the indicator on a solid surface away from sources of vibration.
Install the indicator in a place that does not exposed to direct sunlight.
Install the indicator in an area where it is not subject to direct flow from the window, electric
fan or air conditioner.
Grounding
Be sure to ground the indicator to avoid electrical shock, fire or malfunction.
Precautions for use
Do not apply shock or excessive external force to the weighing conveyors.
Do not apply a load exceeding the weighing capacity to the weighing conveyor.
Do not modify or disassemble the indicator and conveyor. Do not change the parts.
Install the weighing conveyor to horizontal level.
Keep feeding of product with a constant interval.
Cooling the Indicator
To avoid overheating of the indicator, make enough clearance from other devices. If the
temperature surrounding the indicator exceeds the operating temperature range, use fan for
forced cooling to the indicator so as not to effect to weighing.

AD-4412-CW, AD-4413-CW 9
1.3.
Compliance
Adaptation for local laws
The indicator has been tested and complies with Subpart J of Part 15 of FCC rules.
(FCC = Federal Communications Commission in the U.S.A.)
The indicator equips a licensed wireless communication unit used 2.4 GHz band that specifies
2AC7Z-ESPWROOM02 to FCC ID. This license area is Japan and U.S.A. If you use other area,
ask concerning of approval to local authority.
Cautions of wireless LAN (WiFi)
If the communication function of this scale is used near a wireless device that communicates in
the 2.4 GHz range, the processing speed of both devices may decrease.
The wireless band using the scale is used by microwave oven, industry, science, medical
device, mobile identifier in factory and licensed radio station and radio station of no license.
Confirm that there is no these radio stations and mobile identifier around the weighing
indicator.
If radio interference by the indicator is occurred to radio station of mobile identifier, change
the frequency or stop transmission of radio wave. (Example: Use of partition. Installation to
other place etc.)
2.4 ：Wireless equipment of 2.4 GHz band.
DS ：Modulation method is direct-sequence spread spectrum (DS-SS).
4 ：The distance to occur radio interference is 4 m or shorter.
：The whole range is used and it cannot avoid band of mobile identifier.
2.4 DS 4

10 AD-4412-CW, AD-4413-CW
2. Parts Names
This section is described for name of each part.
2.1. Front Panel
1. Touch screen for
indication and operation
2. Start button
3. Stop button
4. USB terminal cover
Drawing 1Front panel of AD-4412-CW
1. Touch screen for
indication and operation
2. Start button
3. Stop button
Screw (M4)
Screw (M3) 5. CAL cover
Drawing 2Front panel of AD-4413-CW
Table 1Names and functions of front panel
No.
Name
Description and Function
1.
Touch screen
The indication and settings of weighing can be displayed and operated.
2.
Start button
Weighing can start and conveyor can run.
3.
Stop button
Weighing and conveyor can stop.
4. USB terminal cover
Waterproof cover for the USB terminal.
A USB terminal is equipped on AD-4412-CW.
5. CAL cover
The cover to prevent unnecessary operation of the calibration switch on
AD-4413-CW.

AD-4412-CW, AD-4413-CW 11
2.2. Rear Panel
1. Optional ports 6. I/F terminals
3. Input terminals of load cell 7. Power switch
8. Power cord terminals
4. RS-232C
5. Control I/O 9. LAN connector
Drawing 3Rear panel of AD-4412-CW
1. Optional ports 6. I/F terminals
2. USB terminal
7. Power switch
3. Input terminals of load cell 8. Power cord terminals
4. RS-232C
5. Control I/O 9. LAN connector
Drawing 4Rear panel of AD-4413-CW
Table 2Names and functions of rear panel
No.
Name
Description and Function
1.
Optional ports
Two optional boards can be installed in maximum.
2.
USB terminal
Terminal to connect USB device on AD-4413-CW.
3.
Input terminals of load cells
Four 350 Ωload cells can be connected in maximum.
4.
RS-232C
It is used to communicate printer, barcode reader and computer.
5. Control I/O
It is used to control peripherals.
Input :11 points. Output :11 points.
6. I/F terminals
RS-485 and photo eye sensor terminals.
It is used for stream mode and communication with PLC using
Modbus RTU. It uses as power source of photo eye sensor.
7.
Power switch
It is the main power supply switch for the indicator.
8.
Power cord terminals
Power supply range :100-240 V ~
9. LAN connector
It is used communication using Modbus TCP and a PDF output
to the printer on network.

12 AD-4412-CW, AD-4413-CW
3.
Installing the Weighing Indicator
Procedures of installing the indicator and connecting power line are described in this chapter.
3.1.
USB Flash Drive
3.1.1.
Connecting USB Flash Drive
The terminal are used when product image data is registered and output data is stored into
USB flash drive.
If you use USB flash drive, open the cover and connect USB flash drive to the USB terminal.
When USB flash drive is identified by the indicator, USB mark is displayed at right-upper side of
the screen.
Caution
Use USB flash drive formatted in FAT32.
If USB flash drive of other format is used, format it in FAT32 before use.
If USB mark is not displayed after connecting USB flash drive, it may be incompatible to file
system of operation system.
USB memory means USB flash drive.
Refer to "8.1 Format of USB Flash Drive" and format USB flash drive.
AD-4412-CW AD-4413-CW
USB flash drive USB terminal cover USB flash drive
Drawing 5USB Flash Drive
3.1.2.
Removing USB Flash Drive
Caution
If USB flash drive is removed using method without the following procedure, it may cause a
failure concerning storing data file.
Step 1. Press and hold the USB mark at right-upper side of the screen when removing USB flash
drive.
Step 2. After the USB mark hides, remove the USB flash drive.

AD-4412-CW, AD-4413-CW 13
3.2. Installing Option board
In first, install the option board. Next, operate them.
An option board can install to an arbitrary slot of either two slots.
Danger
Turn off power switch and remove power lines when removing cover of option board.
Warning
Do not touch the inside of the indicator immediately after turning off the power. It may cause
catch electrical shock. Wait for 10 seconds and operate them.
Caution
Fix screws securely and do not leave loosen screw. If a loosen screw is left, electrical circuit
may short during use. It may cause malfunction due to noise.
Drawing 6Installing option bard
3.3. Mounting the Weighing Indicator on Panel
The installation of the indicator is the panel mounting
using slide rails. When sealing gasket for the panel
mounting is used, the front panel is waterproof
structure complied with IP-65.
Front panel
Sealing gasket Panel
Drawing 7Mounting weighing indicator on panel

14 AD-4412-CW, AD-4413-CW
+0.3
0
+0.3
0
3.3.1. Panel Mount Kit ( AD-4412-10 )
Step 1. Attach the sealing gasket to the indicator with its correct direction.
Step 2. Mount the indicator on the panel so as not to be kinked sealing gasket.
Step 3. Slide attachment parts on trenches of both side. Fix the indicator using attachment parts
and screws (two M4x12) to be able to protect from water.
Step 4. Check the installation.
Step 1..Indicator Step 2..Indicator
Step 1..Step 2..
Panel
Sealing gasket
Step 3..
Step 3..
Step 4..
M4x12 screw Attachment part
190
Panel cutout dimensions
182
4-R15
Drawing 8Panel Mount Kit ( AD-4412-10 )

AD-4412-CW, AD-4413-CW 15
3.3.2. Attachment Kit ( AD-4412-11 ) for Indicator Stand ( AD-4402-25 )
Step 1. Remove two M3x8 screws and two M4x15 screws on the rear panel on the indicator.
Step 2. Attach guide plates on the rear panel.
Interpose guide plates between the rear panel and screws of step 1.
Fix these screws and guide plates.
Step 3. Slide the indicator along slide rails on the indicator stand.
Step 4. Fix the indicator using two M4x8 screws included in accessory of attachment kit.
Step 5. The angle of the indicator can arrange using two knobs.
Indicator
Step 2.
Step 1.
M4x15 screw Step 5.
M3x8 screw Guide plate Knob
Indicator stand
Step 3.
Slide rail
Step 3.
Step 4.
Indicator stand
M4x8 screw
Step 4.
M4x8 screw Knob
Drawing 9Panel Mount Kit ( AD-4412-11 )

16 AD-4412-CW, AD-4413-CW
3.4. Connecting Load Cell Cables
We recommend that you use the 6-wire shielded cable to prevent loss of weighing precision.
If long load cell cables or summing box is used, use 6-wire shielded cable to prevent drift of
weighing value due to temperature change. The 4-wire shielded cable (that is shorted EXC+&
SEN+and shorted EXC-& SEN-) is able to use, but it may cause weighing error when the
summing box is used for plural load cells or long cable is used.
AD-4421-CW 6-wire shielded load cell cable Load cell
1 EXC+Positive power supply to load cell EXC+
2 SEN+Positive sense input
3 SEN-Negative sense input
4 EXC-Negative power supply to load cell EXC-
5 SIG+Positive input from load cell SIG+
6 SIG- Negative input from load cell SIG-
7 SHLD Shield
Drawing 10 Connecting load cell cable (6-wire)
Compensating Voltage Output at Zero Point
When the zero calibration is performed, if the output voltage of the load cell at the zero point is
too large (the message "CERR2" is displayed) and it is too small (the message "CERR3" is
displayed), the output voltage can be adjusted by adding a correction resistor as Drawing 11.
Use the correction resistor of low (good) temperature coefficient.
In Case of Too Large Offset of Zero Point
Positive power supply to load cell
Positive sense input Correction resistor
Negative sense input
Negative power supply to load cell
Positive input from load cell
Negative input from load cell
Load cell
In Case of Too Small Offset of Zero Point
Positive power supply to load cell
Positive sense input Correction resistor
Negative sense input
Negative power supply to load cell
Positive input from load cell
Negative input from load cell
Load cell
Drawing 11 Adjusting voltage output at zero point
Adaptable Compression Terminal Parts (M3)
1.25 1.0
3.2 3.2

AD-4412-CW, AD-4413-CW 17
3.5. Connecting Power Lines
The Indicator can connect to power line of 100-240 V ~ .
Do not share the power cord with an electric power device to avoid operation errors.
Ground the indicator certainly.
Do not use an unstable power source.
Do not share the ground wire with an electrical device that generates noise.
Warning
Ground the indicator to avoid an electric shock or operation error. If the indicator is not
grounded, it may cause an electric shock or malfunction due to discharge of static electricity.
Live terminal
Neutral terminal 100-240 V ~ , 50Hz or 60Hz
Noiseless stable single phase power source
PE terminal
Ground
Drawing 12 Connecting Power Lines
Adaptable Compression Terminal Parts (M4)
1.25 1.0
4.3 4.3

18 AD-4412-CW, AD-4413-CW
4.
Operation Window
Basic operations of the touch screen equipped in the indicator is described in this chapter.
4.1.
Icon
This section describes the function of the common icon.
Other icons describes at each operation.
Icon
Name
Description and Function
Home key The key to return to weighing display.
Return key
The key to back to last window. If you touch the key plural times, the
indicator backs to weighing display.
Left arrow key
The key to move the cursor position of product selection, setting
menu and plural pages on the display.
Right arrow key
Up arrow key
Down arrow key
4.2.
Numerical Input
When numerical input is performs, the numerical dialog box is displayed.
1. The "BS" key to delete a numeric character input last. The cursor proceeds back one character.
2. The "CLR" key to delete all numeric characters.
3. When the "ESC" key is touched, the current input value is canceled and the dialog box is closed.
4. When the "ENT" key is touched, the current input value is stored and the dialog box is closed.
If an input value is out of range, it does not stored.
1. "BS" key
2. "CLR" key
3. "ESC" key
4. "ENT" key
Drawing 13 The numerical dialog box
Display
Input keys