AND AD-4430B User manual

1WMPD4002678C
AD
AD- -4430B 4430B
with BCD Output
with BCD Output
DIN
DIN Rail Weighing Rail Weighing Module Module

This manual and Marks
All safety messages are identified by the following, “WARNING” or
“CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product
Safety Signs and Labels). The meanings are as follows:
WARNING
A potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION A potentially hazardous situation
which, if not avoided,
may result in minor or moderate injury.
This is a hazard alert mark.
This manual is subject to change without notice, at any time, to improve the
product.
The contents of the product specifications and this manual are subject to
change without any obligation on the part of the manufacturer.
Under the copyright laws, the software (program) described in this manual is
copyrighted, with all rights reserved.
The software may be installed into one computer and may not be installed
into other computers without the prior written consent of A&D Company,
Limited. Copying includes translation into another language, reproduction,
conversion, photocopy and offer or loan to another person.
2014 All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, or
translated into any language in any form by any means without the written
permission of A&D Company, Limited.

AD-4430B - 1 -
Contents
1. Compliance .................................................................................................................................4
1.1. Compliance with FCC rules ..................................................................................................4
1.2. Compliance with European Directives .................................................................................4
1.3. Precautions For Safety Use ..................................................................................................4
2. Outline and Features ..................................................................................................................6
3. Specifications ..............................................................................................................................7
3.1. Analog Part (Load cell Input, A/D Converter).......................................................................7
3.2. Display And Keys................................................................................................................... 7
3.3. General...................................................................................................................................7
3.3.1. Interface............................................................................................................................7
3.3.2. Weighing Function...........................................................................................................8
3.3.3. General.............................................................................................................................8
3.3.4. Accessories......................................................................................................................8
3.3.5. Dimensions ......................................................................................................................9
3.4. Names (The Front Panel And Rear Panel ).......................................................................10
4. Installing The Module................................................................................................................ 11
4.1. Conditions To Install The Module........................................................................................ 11
4.2. Power Supply....................................................................................................................... 11
4.3. Connecting Load Cell Cable ...............................................................................................12
4.4. Verifying Load Cell Cable ....................................................................................................13
5. Operations.................................................................................................................................14
5.1. General Functions................................................................................................................14
5.1.1. Zero Adjustment.............................................................................................................14
5.1.2. Zero Tracking .................................................................................................................14
5.1.3. The Tare Function..........................................................................................................14
5.1.4. Clearing The Tare Value And Zero Operation..............................................................15
5.1.5. Customizing The Function Of the F Key......................................................................15
5.1.6. Customizing The Function Of the x Display.................................................................16
5.1.7. Memory Backup.............................................................................................................16
5.1.8. Near-Zero Detection......................................................................................................16
5.1.9. Upper Or Lower Limit Detection Function....................................................................16
5.1.10. The Hold Function .........................................................................................................17
5.2. State Diagram And Operation Switches.............................................................................18
5.2.1. State Diagram ................................................................................................................18
5.2.2. Operation Switches .......................................................................................................19
5.3. Calibration.............................................................................................................................20
5.3.1. Outline ............................................................................................................................20
5.3.2. Calibrating With A Weight ()............................................................................21
5.3.3. Gravity Acceleration Correction ....................................................................................22
5.3.4. Digital Linearization........................................................................................................23
5.3.5. The Actual Load Linearization Function ( ).....................................................24
5.3.6. The Calibration Function ( ).............................................................................25

- 2 - AD-4430B
5.3.7. The Linearization Function ( ) .........................................................................29
5.3.8. Error Codes For The Calibration...................................................................................30
5.3.9. Adjustment Of The Loadcell Output .............................................................................30
5.4. General Functions................................................................................................................31
5.4.1. The Procedure To Store New Parameters ..................................................................31
5.4.2. The Adjustment Of The Digital Filter.............................................................................32
5.4.3. The Basics Function ( )....................................................................................33
5.4.4. The Hold Function ( ).......................................................................................34
5.4.5. The BCD Function ( ).......................................................................................35
6. Interface.....................................................................................................................................36
6.1. The Parallel BCD Output.....................................................................................................36
6.1.1. Timing Chart Of The BCD Output ................................................................................36
6.1.2. Terminals Of The BCD Output......................................................................................36
6.1.3. The State Of The BCD Output......................................................................................36
6.1.4. Positive Logic And Negative Logic ...............................................................................37
7. Maintenance..............................................................................................................................38
7.1. Error Messages....................................................................................................................38
7.2. Check Mode.........................................................................................................................38
7.2.1. Entering The Check Mode ............................................................................................38
7.2.2. Verifying The Switch Operation ....................................................................................39
7.2.3. Checking The BCD Output ...........................................................................................39
7.2.4. Monitoring The A/D Converter ( For Load cell Output)................................................39
7.2.5. Monitoring The Internal Value .......................................................................................39
7.2.6. Monitoring The Program Version..................................................................................39
7.2.7. Monitoring The Serial Number......................................................................................39
7.2.8. Monitoring The Checksum Of The Program ...............................................................39
7.2.9. Monitoring The Checksum Of An Internal FRAM........................................................39
7.2.10. Displaying Function Parameters For The Calibration ( )...............................39
7.3. Initializing Parameters..........................................................................................................40
7.3.1. Initializing Mode For RAM And Function Parameters.................................................40
7.3.2. Initializing The Whole Data............................................................................................40
7.4. Verifying The Load Cell Connections ( DIAGNOS )..........................................................41
7.4.1. Guideline To Verify The Load Cell Connections ..........................................................41
7.4.2. The Operation With The BCD Input .............................................................................41
7.4.3. Verifying Load Cell Connections with Switch Operation.............................................42
7.4.4. Display and Output of Check Results ..........................................................................42
7.5. Verifying The Load Cell Connections Using Multimeter....................................................43
7.5.1. Check List Of The Load cell Connections....................................................................43
7.6. The Parameter List For The Function List..........................................................................45
7.6.1. The Calibration Function ( ).............................................................................45
7.6.2. The Linearization Function ( ) .........................................................................47
7.6.3. The Basics Function ( )....................................................................................47
7.6.4. The Hold Function ( ).......................................................................................49
7.6.5. The BCD Function ( ).......................................................................................49

AD-4430B - 3 -
Illustrations
Illustration 1 Dimensions.....................................................................................................................................9
Illustration 2 Front panel & rear panel............................................................................................................ 10
Illustration 3 Mounting the module ................................................................................................................. 10
Illustration 4 Wiring the connectors .................................................................................................................11
Illustration 5 Load cell connection .................................................................................................................. 12
Illustration 6 Peak hold / Averaging hold ....................................................................................................... 17
Illustration 7 State diagram.............................................................................................................................. 18
Illustration 8 Gravity Acceleration Graph....................................................................................................... 23
Illustration 9 Digital linearization ...................................................................................................................... 23
Illustration 10 Load cell output adjustment ................................................................................................... 30
Illustration 11 Wire Name of Load Cell.......................................................................................................... 41
Illustration 12 Connection Check of Load Cell............................................................................................. 43

- 4 - AD-4430B
1.
Compliance
1.1.
Compliance with FCC rules
Please note that this equipment generates, uses and can radiate radio frequency energy.
This equipment has been tested and has been found to comply with the limits of a Class A
computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to
provide reasonable protection against interference when this equipment is operated in a
commercial environment. If this unit is operated in a residential area it may cause some
interference and under these circumstances the user would be required to take, at his own
expense, whatever measures are necessary to eliminate the interference.
(FCC = Federal Communications Commission in the U.S.A.)
1.2.
Compliance with European Directives
This appliance complies with the statutory EMC (Electromagnetic Compatibility) directive
2004/108/EC and the Low Voltage Directive 2006/95/EC for safety of electrical equipment
designed for certain voltages.
Note: The displayed value may be adversely affected under extreme electromagnetic influences.
1.3.
Precautions For Safety Use
Before use, confirm the following articles for safe operation.
Grounding The Module
Ground the module to the DIN rail with certainty. Separate this earth ground line from others,
like ground line of a motor, inverter or a power source. Unless the indicator is grounded, it
may result in receiving an electric shock, cause operation error or catch fire.
Proper Power Source And Power Cable
Confirm the AC voltage, frequency and power tolerance of the power cable. If the voltage
range of the cable is lower than the power line voltage, it may cause leakage or catching fire.
Use pole compression terminals to connect the power cable to the terminals.
Fuse
The fuse is installed to help prevent the module from catching fire. The module is equipped
with many safety circuits. Therefore, the fuse is not damaged in normal operation. If the fuse
is damaged, do not replace it, contact your local A&D dealer. This trouble may have been
caused by strong electric discharge.
Splashing Water
The module is not water resistant.
Flammable Gas
Do not install the module where flammable gas is present.
Heat Radiation Of The Module
Space out instruments to radiate heat sufficiently. Use a cooling fan to keep the operating
temperature of the module within specifications.
AD-4430B is covered with a protective transparent-resin cover. After the installation is
complete, take off the protective cover prior to turning on the AD-4430B. Heat damage may

AD-4430B - 5 -
be caused if you do not remove the protective cover.
The protective cover is for preventing wire chips when you will install and wire so
please do not take off the cover until complete the installing and wiring.
Protective cover
AD-4430B
Data communication with RS-485 (Modbus
RTU)
AD-4430B
Protective cover
Pull
this way
Take off the two tabs on the back of
the protective cover.
1
2
How to remove the protective cover
AD-4430B with a protective cover

- 6 - AD-4430B
2.
Outline and Features
The AD-4430B has the following features.
The AD-4430B is a weighing indicator that amplifies signals from a load cell, converts it to
digital data and displays it as a mass value.
This indicator has the following performance :
Input sensitivity :............................ 0.15 µV / d (d = minimum division)
Display resolution :........................ 99,999 d in maximum
Sampling rate :............................... 1000 times/second
Input voltage range :...................... -35 mV to +35 mV (-7 mV/V to +7 mV/V)
The calibration using gravity acceleration correction :
The function compensates for weighing error due to the difference of gravity acceleration
between the calibration place and the measurement place.
The digital linearization function :
The digital linearization function can rectify and reduce the linearity deviation using weighing
points during the zero and capacity setting. Up to four weighing points can be specified. The
high-order correction curve is used between each points.
The digital span mode :
Simplified calibration is possible using numerical input, even without an actual load.

AD-4430B - 7 -
3.
Specifications
3.1.
Analog Part (Load cell Input, A/D Converter)
Input sensitivity 0.15 µV/d or greater (d = minimum division)
Input voltage range
-
35 mV to
+
35 mV (
-
7 to
+
7 mV/V)
Zero range
-
35 mV to
+
35 mV (
-
7 to
+
7 mV/V)
Load cell excitation voltage
(Load cell drive capacity)
5 VDC ±5%, 60 mA with remote sensing capability
(Maximum 4 x 350 Ωload cells)
Temperature coefficient Zero
±
0.02 μV/°C Typ.
±
0.1 μV/°C Max.
Span
±
3 ppm/°C Typ.
±
15 ppm/°C Max.
Non-Linearity 0.005% of full scale Max.
A/D conversion method Delta-sigma method
A/D resolution count Approximately 16,000,000 counts
Display resolution 99,999 d Max. (d = minimum division)
Sampling rate 1000 times/second
3.2.
Display And Keys
Display element Measurement display 5 - digit 7-segment green LED
Status indicators 6 red LEDs
Measurement
display
Numerical display Switches between NET and GROSS
Decimal point Selectable decimal places (101, 102, 103, 104)
Overflow display All the digits turn OFF. (When the polarity is negative,
the minus sign appears at the highest-order digit.)
Status indicators : GROSS, : NET, : HOLD, : STABLE, : ZERO,
: Selectable from the function list of X display ( ).
Key switches /
ESC
, (ZERO), (TARE),
3.3.
General
3.3.1.
Interface
BCD Output MDR connector 36pins female type
BCD Output And I/O Output I/O Input
Output circuit Open collector transistor Input circuit DC contact input
Isolation Photo coupler Open voltage Approx. 5 V
Output current 50 mA Max. OFF current 0.1 mA Max.
Saturation voltage 0.5V Max. @50 mA ON current 2 mA Min.
Threshold voltage 2V
Chattering suppression time 10 msec.

- 8 - AD-4430B
3.3.2.
Weighing Function
Zero adjustment
Sets the gross weight to zero by pressing the (ZERO) key.
Selection of disable or enable for the operation when unstable.
The zero value is backup by FRAM.
Zero adjustable range : Can be set optionally in the range of 1 to 100% of the
weighing capacity.
Zero tracking
Tracks the weight drift around the zero point to maintain zero.
Zero tracking time : 0.0 to 5.0 seconds Can be set optionally within the range
Zero tracking width : 0.0 to 9.9 d Can be set optionally within the range
Tare
Sets the net weight to zero by pressing the (TARE) key.
The tare weight is backup by FRAM.
Tare range : Gross weight ≤Weighing capacity
Stability detection
Turns ON the stabilization indicator when the variables of the weight values per
sampling are within the set band in the set time.
Stability detection time : 0.0 to seconds Can be set optionally within the range
Stability detection width : 0 to 9d Can be set optionally within the range
Digital filter Cutoff frequency (
-
3 dB) range : 0.7 to 100 Hz
Zero detection Detects to place nothing on the weighing pan.
Comparator Compares the measurement with these limits and outputs the results.
Hold function Displays the measurement value held.
Select from normal hold, peak hold, averaging hold.
3.3.3.
General
Data backup
Power failure countermeasure
Zero value, tare weight, calibration, function parameters backup by
FRAM. (Approx. 10 years)
Power source DC 24 V,
+
10%,
-
15%
Power consumption Approximately 6 W Max.
Operating temperature
Operating humidity
-10 °C to +50 °C,
85 %RH or less (no condensation)
Installation method DIN rail mount
Mass Approximately 180 g
3.3.4.
Accessories
Item Quantity Model name
Power source connector 1 FMC1.5/2-ST-3.5

AD-4430B - 9 -
35.3
(2.5)
100
1.3
39.4
20°
28
110
34.5
5.5
36.1
Illustration 1Dimensions
3.3.5. Dimensions
Unit : mm
A&DCompany, Limited

- 10 - AD-4430B
3.4. Names (The Front Panel And Rear Panel )
Main display
Status indicators
Key switches
Vent
Sensor terminals
of load cell
Guide for DIN rail
BCD connector
Power supply
connector
Hook for DIN rail
Pull down it when removing.
Vent
Guide for DIN rail
DIN rail
Illustration 2Front panel & rear panel
Illustration 3Mounting the module

AD-4430B - 11 -
Illustration 4Wiring the connectors
4. Installing The Module
This section is explained for the environment to install the module and for the terminals of the
power source and load cell cable. Refer to each section of options for I/O interface.
4.1. Conditions To Install The Module
The module is a precision electronic instrument. Handle it carefully.
The operating temperature is -10°C to +50°C.
Do not install the module in direct sunlight.
4.2. Power Supply
Earth ground the module to prevent electrical shock or indicator malfunction.
If the module is not grounded, it may cause of an electric shock, or malfunction due to static electricity.
Before connecting the module to the power source, read the instruction manual thoroughly.
Do not connect the module to the power source before the installation is complete.
To avoid electrical shock, do not handle the power cable with a wet hand.
Earth ground the module. Do not share the ground line with other electrical power equipment.
The power requirement is 24 DCV, +10% to -15%.
Use a stable power source free from instantaneous power failure or noise.
To avoid a malfunction, do not share the power line with other devices.
The output voltage of a load cell is a very sensitive signal. Keep all electrical noise sources
away from the load cell and load cell cable.
Use shielded I/O cables. Connect the cable shield to the F.G. terminal or the module housing.
Ground terminal is connected internally with all connector shields.
The Conductor Specifications
Clamp range (typ.)
0.13 mm2to 1.5 mm2
AWG
AWG24 - AWG16
Solder plated wire
0.2 mm2to 1.5 mm2
Twisted wire
0.2 mm2to 1.5 mm2
Rod crimp terminal DIN 46228 Part 1
0.25 mm2to 1.5 mm2
Rod crimp terminal with cover DIN 46228 Part 4
0.25 mm2to 0.75 mm2
Lead length
8 mm
Push buttons when connecting and
removing the cables.
Rod type crimp terminal
Refer to "The Conductor Specifications".
Shielded load cell cable
Accessory connector
Power cable
Press the button to
remove & insert it.

- 12 - AD-4430B
4.3. Connecting Load Cell Cable
Shield Cable Connection
As a general rule, only connect the load cell cable's shield wire to the module's shield
terminal. This is because when there are multiple ground points, it becomes easier for noise
to occur as a result of a ground loop. However, when there are higher priorities than noise
prevention, such as explosion prevention systems or static electricity release routes, this rule
does not necessarily need to be followed.
Load Cell Terminal Connections
Two types of load cell connection are available: 6-wire connection and 4-wire connection.
For high precision and stable weighing, 6-wire connection is recommended.
Terminal No.
Terminal Name & Function
1
SIG-
Load cell input (-)
2
SIG+
Load cell input (+)
3
EXC-
Load cell excitation voltage (-)
4
SEN-
Sensing input (-)
5
SEN+
Sensing input (+)
6
EXC+
Load cell excitation voltage (+)
7
SHLD
Shield
6-wire connection to load cell (recommended)
4-wire connection to load cell (not recommended)
Illustration 5Load cell connection

AD-4430B - 13 -
Type
Advantages
Disadvantages
Description
6-wire
connection
(recommended)
The error is small even
when the load cell cable
is extended, a thin load
cell cable is used, or
multiple load cells are
used.
Complicated wiring
Use a 6-wire shielded
cable when a summing
box is used.
4-wire
connection Simple wiring
The influence of the
load cell cable
resistance worsens the
temperature coefficient.
Prone to the influence of
the contact resistance of
the connector
The error increases
when the load cell cable
is extended or multiple
load cells are used.
Precautions to be taken when using the 4-wire connection:
If the 4-wire connection has to be used, please take the following measures.
Be sure to connect terminals EXC+(6) and SEN+( 5 ) and terminals SEN-(4) and EXC-(3).
When lengthening the load cell cable, try to use cable with a large cross-sectional area.
Also, keep the cable as short as possible.
4.4.
Verifying Load Cell Cable
When the load cell connection is complete, perform a connection check using the following
procedure.
Perform a visual check to ensure that the wiring is correct.
Turn the module on.
When calibration has not yet been carried out, the display value may be blank. However, as
long as there are no problems with the display, confirmation can still be carried out using
check mode.
Enter the check mode and check the load cell output value.
Refer to “
7.2. Check Mode
" to enter the A/D check mode.
Confirm that the displayed load cell output value matches the specified value. Normally the
displayed value will be the load cell rated output value or less.
If an error occurs, refer to "
7.4 Verifying The Load Cell Connections ( DIAGNOS )
" or "
7.5
Verifying The Load Cell Connections Using Multimeter
".

- 14 - AD-4430B
5.
Operations
5.1.
General Functions
5.1.1.
Zero Adjustment
Zero adjustment is a function to set the gross weight to zero.
It is performed by pressing the (ZERO) key.
The zero adjustment range is set in ( Zero range ) and is expressed in percent of the
weighing capacity with the calibration zero point as the center.
Zero adjustment is disabled, even within the zero adjustment range, when the A/D converter
overflow occurs.
A ZERO error is output if zero adjustment is not performed.
The zero value is stored in the non-volatile memory and is maintained, even if the power is
disconnected.
Clearing the zero value is performed using the key assigned to clear the zero value.
Functions Related To Zero Adjustment
( Zero range ) : A value between 0% and 100% can be specified.
( Tare and zero adjustment when unstable ) :The selection to enable or disable
tare and zero adjustment when unstable.
( Zero setting when power is turned on ) :The selection whether or not to perform
zero setting when power is turned on.
5.1.2.
Zero Tracking
The zero tracking is a function to track the gross weight drift around the zero point to maintain zero.
The zero tracking time is set in ( Zero tracking time ) and the zero tracking width is
set in ( Zero tracking width ). When the gross weight drift is within the specified
ranges, zero tracking is performed automatically.
A ZERO error is not output even if zero tracking is not performed.
Functions Related To Zero Tracking
( Zero tracking time ) :The value between 0.0 and 5.0 seconds can be specified.
( Zero tracking width ) :The value between 0.0 and 9.9 d can be specified.
(d = minimum division)
5.1.3.
The Tare Function
Tare is a function to store the gross weight as the tare value and set the net weight to zero.
It is performed by pressing the (TARE) key.
The tare weight is stored in the non-volatile memory and is maintained, even if the power is
disconnected.
Clearing the tare weight is performed using the key assigned to clear the tare weight.
Functions Related To The Tare Function
( Tare and zero adjustment when unstable ) :The selection to enable or disable
tare and zero adjustment when unstable.
( Tare when the gross weight is negative ) :The selection to enable or disable
tare when the gross weight is negative.

AD-4430B - 15 -
5.1.4.
Clearing The Tare Value And Zero Operation
To clear the tare value and zero operation, hold the (TARE) key and turn on the module. Or:
In off mode, hold the (TARE) key and press the key.
5.1.5.
Customizing The Function Of the F Key
Assigns a function to the key from the functions of ( key function) below :
0: None
1: Manual print command
2: Hold
3: Alternate switch
4: Momentary switch
5: Display selection
6: Clear the tare weight
7: Clear the zero value
( Clear the zero value ) :Enable or disable clearing the zero value.
0: Disable 1: Enable
Alternate switch and momentary switch
By assigning these switches to the key, the ON/OFF status of the key can be
transmitted to the master station. This is useful when building a network or performing
maintenance. The function of the x display can be specified by the key and can be
monitored by the linked memory. These switches work as follows :
Alternate switch
When pressing and releasing the switch once, the state of the switch is maintained.
Press the switch again to turn off or on.
Momentary switch
Only while the switch is being pressed, the switch is ON. When it is released, it is OFF.

- 16 - AD-4430B
5.1.6.
Customizing The Function Of the x Display
Assigns a function to the xdisplay (a red LED) from the functions of (xDisplay) below:
0: None
1: Zero tracking in progress
2: Alarm (Zero range setting error, over)
3: key status
4: Near-zero
5: HI output (Over the upper limit value)
6: OK output (Between upper and lower limit values)
7: LO output (Below the lower limit value)
8: User input 1
9: User output 1
5.1.7.
Memory Backup
Zero value, tare weight, calibration data and function data are written into non-volatile
memory (FRAM). The FRAM does not require batteries. The data retention period is 10
years. Therefore, this module does not equipped the backup battery.
5.1.8.
Near-Zero Detection
Near-zero detects whether an object has been placed on the weighing pan.
The near-zero state is defined when the weighing value is within the preset value for the near-
zero range.
Related Functions
( Near-zero ): The value of near-zero.
( Near-zero comparison weight ): Selection of the gross weight or net weight to
compare the value of near-zero.
1: Gross weight 2: Net weight
5.1.9.
Upper Or Lower Limit Detection Function
This is a function to detect whether the weighed value is above an upper limit value or below a
lower limit value.
Functions Related To The Detection Function
(Upper limit value) or (Lower limit value) :A comparative upper or lower
limit value can be set.
(Comparison mass of upper and lower limit) :Gross weight or net weight to be
compared with the upper or lower limit value can be selected.
(Output logic of upper and lower limit) :Positive logic or negative logic to output the
upper and lower limit can be selected.
key status
When alternate switch or momentary switch is selected at , the works.
The display turns ON when the key is ON and turns OFF when the key is OFF.

AD-4430B - 17 -
5.1.10.
The Hold Function
There are three types of hold functions which can be used for different purposes.
Normal hold
Holds the value displayed at the time the hold command was received.
Peak hold
Holds the maximum value reached after the hold command was received.
The value will be refreshed if it increases again.
Averaging hold
This function averages weighing data over a certain period of time and then holds the result.
It is useful for measuring things that are difficult to weigh such as an animal that won’t settle
down, or for averaging out the weight of an object in an unstable state. In addition, it can
reduce the effects of breezes which the digital filter cannot eliminate.
Functions Related To The Hold Function
(Hold function) :The type of hold function can be selected.
To set operating conditions for the hold function :Set the averaging time length, standby
time, or start and stop conditions with to . (Will not affect normal holds)
Peak hold
Averaging hold
Averaging (Busy state)
(Averaging time)
Hold
Hold start command
Automatic start condition
Averaging start Averaging finish Hold cancellation
command
Automatic cancellation condition
Standard
state
Standard
state
Hold
Hold start command
Automatic start condition
Hold cancellation command
Automatic cancellation condition
Standard
state
Standard
state
Hold
Judgment start
Illustration 6Peak hold / Averaging hold

- 18 - AD-4430B
5.2.
State Diagram And Operation Switches
5.2.1.
State Diagram
The nonvolatile memory always stores either OFF mode or other mode. It starts from the following
state depending on the mode that has been kept when the automatic power is on.
OFF mode ( standby ) : Starts from OFF mode.
Other mode : Starts from Weighing mode.
State diagram can be switched as follows.
key to select
Power on
Weighing mode
Automatic power on
Function mode
OFF mode
(standby ) display
Automatic power on after setting
ON state
Check mode
Display
Initialization mode
display
*2
*3
*1
Self-check mode
display
display
OFF state
*4Calibration using actual
load
display
Function mode related to
calibration
display
*1
*2
*3
*4
display
Digital linearization mode
display
display
Function mode related to
digital linearization mode
All data initialization mode
Illustration 7State diagram