AND TM2440-EX User manual

1
1WMPD4004497
Thank you for purchasing the Ambulatory Blood Pressure Monitor TM2440-EX. The Instruction Manual that
accompanies the product has been corrected and had content added. Please read it in conjunction with the
details shown below.
The following changes have been made.
Wrong Correct
The initial pressurization value is set to 180 mmHg at the
factory.
The initial pressurization value for automatic blood pressure
measurement is AUTO.
In the case of AUTO, the appropriate pressurization value
is set automatically.
The following changes have been made.
Wrong Correct
The initial pressurization value is set to 180 mmHg at the
factory.
The initial pressurization value setting is AUTO
(appropriate pressurization value set automatically) when
the mark is displayed and 180 mmHg when the
mark is hidden.
The following is added after "A-BPM can use only while the automated measurement can be performed. "
Addition
Note
The Start time and Operation time are initially set calculating from the
time at which the mark was displayed. When the next
automatic measurement is made, this needs to be set again.
Ambulatory Blood Pressure Monitor TM2440-EX,
Instruction Manual, Corrections and Additions
Instruction manual Page 22 6.1. Automatic Blood Pressure Measurement (A-BPM)
Instruction manual Page 37 8.2.3. Initial Pressurization Value
Instruction Manual Page 37 8.3. A-BPM Preset Programs

2
1WMPD4004497
The following changes have been made.
Wrong Correct
#3: Example for automated measurement.
Start time : Stores a time. (0 to 23 hour)
Operation time : Set to "OFF"
Response :
A-BPM starts the blood pressure measurement
at the preset Start time and continues until
A-BPM is suspended.
If the EVENT switch is pressing and holding
until the mark is shown, A-BPM starts at
the preset Start time.
#3: If the Start time for automatic measurement is specified
and the Operation time is set to "OFF", long pressing
the EVENT switch will start automatic blood pressure
measurement from the Start time set and measurement
will continue until the EVENT switch is long pressed.
If the EVENT switch is long pressed again, automatic
measurement will continue.
Note
If the Operation time is set, automatic blood pressure
measurement will be performed from when the EVENT
switch is initially long pressed until the Operation time
has passed even if the EVENT switch is long pressed
midway through automatic measurement.
#4: Example for automated measurement.
Start time : Set to "OFF"
Operation time : Stores time to be continued.
(1 to 27 hours)
Response :
A-BPM starts blood pressure measurement
and stops after the Operation time.
If the mark is hidden by pressing and
holding the EVENT switch during the
Operation time, A-BPM stops.
If the mark is shown by pressing and
holding the EVENT switch again, A-BPM is
performed for the Operation time.
#4: If the Start time for automatic measurement is set to
"OFF" and the Operation time is set, long pressing the
EVENT switch will implement automatic blood pressure
measurement after initial automatic measurement until
the set Operation time has passed. If the EVENT
switch is long pressed midway through automatic blood
pressure measurement, automatic measurement will
stop. If the EVENT switch is long pressed again,
automatic measurement will be performed until the set
Operation time has passed.
Note
If the Start time is set, long pressing the EVENT
switch midway through automatic blood pressure
measurement will stop automatic measurement and long
pressing it again will resume measurement.
The following notes were added to "Example 2 Automatic measurement"
Addition
NB. Automatic blood pressure measurement will continue even if turned "OFF" and "ON" again during
automatic measurement.
The following notes were added to "Example 3 Automatic measurement"
Addition
NB. Automatic blood pressure measurement will not be performed once the Operation time has been
exceeded even if turned "OFF" and "ON" again during automatic measurement.
Instruction Manual Page 42 8.3.2. A-BPM Program Examples
Instruction Manual Page 40 8.3.1. A-BPM Items and Parameters