Anderson Pro.to.go User manual

Anderson Enterprises
2540 Angus Lane Salina, Kansas 67401
phone/fax [phone]
www.an ersonbuzzersystems.com
support@an ersonbuzzersystems.com
The Pro.to.go Portable Buzzer System
Instruction Sheet
Introduction
Congratulations on your purchase of the Officiator Pro.to.go Buzzer System. It has been esigne with
spee , accuracy, an your bu get in min . This System is powere with 3-AA batteries ~ use it while
camping, in the car, or anywhere on-the-go. The Pro.to.go System comes complete with the Mo erator
Mo ule, batteries, your choice of Player Buttons, an a carry case. Player Button choices are: Han -
hel an Player Han pa .
System Set-Up
...with Han -hel Player Buttons
The gray cables connecte to each Han -hel Button in ivi ually plug into the si es of the Pro.to.go
Mo erator. The Pro.to.go System can be use with up to 4 player buttons. To avoi unnecessary wear
to the cables, o not wrap the gray cable aroun each Han -hel button when packing away the system
since this a s unnecessary stress to the cable. The cable can be replace by simply isconnecting an
replacing with our 'C5' cable or any au io cable with male RCA connectors on each en .
Pro.to.go System with and-held Buttons Pro.to.go System with Player andpads
System Set-Up
...with Player Han pa s
The gray cables connecte to each Player Han pa in ivi ually plug into the si es of the Pro.to.go
Mo erator. The Pro.to.go System can be use with up to 4 player buttons. To avoi unnecessary wear
1

to the cables, o not wrap the gray cable aroun each Han pa when packing away the system since
this a s unnecessary stress to the cable. The Han pa cable is har -wire an shoul be sent to our
Technical Department to have its efective cable replace . For more information on parts repair, go to:
http://www.an ersonbuzzersystems.com/support.html at bottom of page
System Power-Up
The Pro.to.go Mo erator has a power-on sli e switch on the right si e of the Mo erator. When
powere -up, the “ON” LED will light an the circuitry will go through a 2 secon self-test after which
time it is rea y for play. To save battery power, remember to turn off your Pro.to.go Mo erator when
not in use. The “ON” LED will be off to in icate power- own. To replace the batteries, see the
instructions below.
ow the Pro.to.go System Works
The Pro.to.go's circuitry etects an in icates which of the 4 player buttons was pushe first. The
accuracy of this etection is within 10 microsecon s. When a button is pushe , the circuitry locks out
the other three buttons so there can be no ties. The one lit LED on the Mo erator Mo ule will remain
lit until the Mo erator's Reset Button is pushe to rea y the system for the next question.
The Pro.to.go Mo erator has a volume control on the left si e. If you hear no soun when buzzing in,
please check to make sure the volume knob is turne all the way clockwise.
Battery Replacement
The Pro.to.go Mo erator is powere by 3 AA batteries. To replace them, simply remove the square
rubber feet on the bottom cover to expose two screws. Remove screws an pop-off bottom cover. The
battery hol er is attache to the reverse si e of the cover with two #2 screws an nuts. Do NOT remove
these screws. Replace batteries, snap on bottom cover (making sure to not pinch any wires with the
cover), an secure with two screws. Replace rubber feet an it's rea y to go. Be sure to replace all three
batteries with new ones. Do not mix ol an new batteries.
Warranty
An erson Enterprises warrants to the original purchaser that the Pro.to.go System is free from efects
in material an workmanship, assuming normal use, for a perio of one year from ate of purchase.
For more warranty information, please check out:
http://www.an ersonbuzzersystems.com/support.html at bottom of page
2