lntroduction
This product is a battery-powered, auto-ranging,
true RIVS digital multimeter with a 600P counts
LCD display.
Safety lnformation
To avoid possible electrical shock, fire, or
personal injury, please read all safety information
before you use the product. Please use the
product only as specified, or the protection
supplied by the product can be compromised.
. Examine the case before you use the product.
Look for cracks or missing plastic. Carefully
look at the insulation around the terminals.
. The measurement must be made within the
allowable measuring range.
. Do not use the product around explosive gas,
vapor, or in damp or wet environments.
. When the voltage to be measured exceeds
36V DC or 25V AC, the operator shall be
careful enough to avoid electric shock.
. [Visuse of mode or range can lead to hazards,
be cautious. o'OL" will be shown on the display
when the input is out of range.
. Low level of a battery will result in incorrect
readings. Change the batteries when battery
level is low. Do not make measurements when
the battery door is not properly placed,
lnstruction Buttons Measurements
Only when,the voltage is higher than 0.8V, this product
will show the display;
The DC or AC voltage will be auto matched;
Touch the probes to the correct test points of the circuit
to measure the voltage;
R.ead the measured voltage on the display.
1. Press the current button to enter current test mode;
Touch the probes to the correct test points of the circuit
to measure the current;
3. Read the measured current on the display.
1. The resistance measure will be auto matched;
Touch the probes to the desired test points of the circuit
to measure the resistance;
Read the measured resistance on the display.
1. ln AC mode, press Hz button to enter frequency test
mode.
,Touch the probes to the desired test points of the circuit
measure the frequency.
Reacj the measured frequency value on the display.
User Manual
,{
i*
t lji
]i;
li
}
t
!ii
\í
f
li
;x
l{řt9/fi l"
}r8 .fi|.
*ilT#pů.,lt$ BFF
.iN* .iil*,i,
ili*.ň i{r l: [:
i;|1i,tixl
,i+,.,*i. ;l****j,
{{
{ s *l}t*]I TF{{"i s}Ws
!
'4.
'1 , Press
2" Touch
to enter in temperature test mode;
probes to the desired test points,
All rights reserved,
Specifications are subject to change without notice.
Read the measured temperature on the display.
-4-
rls Fo|ťER
ili,ďl
push this button over 2 seconds to turn on or turn
off the product.
The product will automatically turn off after 15
minutes of inactivity and the built-in beeper beeps
5 times in 1 minute before auto power off.
To cancel auto power off, push HOLD/REL
button before turning on the product, after 5
beeps to cancel the auto power off successfully.
t{ LDínEL
ět* EL
Push once to hold the current reading on the
display in non-capacitive mode ; push once to
clear data in the capacitive mode; push for more
than 2 seconds to turn on the backlight. And
long-push again to turn off.
ilTi
press this button to enter auto mode.
Automatically sw itch to enter other f unct ions
i nc l ude temperature , frequency , AClDC
vo l tage , res i stance and cont i nu i ty.
Short press this button to automatically switch to
test diode/continuity,capacitance and NCV"
press th i s button to enter cur rent t_est
mode. lt can automatically switch to test-
AC and DC current.
Ml n AC vo l tage mode, i t can i dent i fy
f requency Automatically.
Press to test temperature.
2.
2.
to
HT
Al
o0
ťíF
iB Fstl *
*
