Angelcare AC017 User manual

OWNER’S MANUAL
Model AC017
Movement Monitor
TABLE OF CONTENTS
WARNINGS............................................................................................................................................................................... 2
SETUP REQUIREMENTS.................................................................................................................................................................3
Setting up the Nursery Unit ..........................................................................................................................................................4
Positioning the movement Sensor Pad .....................................................................................................................................4
Turning ON your monitor...............................................................................................................................................................5
Getting to know your monitor......................................................................................................................................................5
Troubleshooting ................................................................................................................................................................................ 7
Limited warranty...............................................................................................................................................................................8
Technical specifications..................................................................................................................................................................8
For assistance, FAQs or guidance with your monitor
please visit our Customer Support page at angelcare.co.uk
01mf6A_Manuel_AC017_UK_12643.indd 1 18-01-24 14:37

1. THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.
This product is designed to aid in the monitoring of your baby. When
using the monitor, you must still provide the supervision necessary for the
continued safety of your baby. Monitoring of premature babies, or those
considered to be at risk, should always be carried out under the supervision
of a health professional. This monitor SHOULD NOT be used as a medical
device, nor as a device to prevent Sudden Infant Death Syndrome (SIDS).
2. ALWAYS be sure to immediately check on baby whenever an alarm
sounds.
3. DO NOT use monitor near water (such as bath tub, sink, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
4. Keep monitor AWAY from heat sources (such as stoves, radiators, etc.).
5. ALWAYS place the Nursery Unit on a flat surface in an upright position
and allow for proper ventilation. DO NOT place on sofas, cushions, beds,
etc. which may block ventilation.
6. This product is NOT a toy. DO NOT allow children to play with it.
7. This product contains small parts. Adult assembly required. Exercise
care when unpacking and assembling the product and keep small parts
away from children.
8. When using the monitor, the room temperature should be between
10°C and 40°C.
BATTERY WARNING
9. The Wireless Sensor Pad battery is a replaceable Button Cell Lithium
battery. Only use the Angelcare®recommended replacement battery.
Danger of explosion if the wrong battery is used or if replaced incorrectly.
Refer to your user manual for correct battery installation. DO NOT short
circuit supply terminals. Remove the batteries from your Nursery Unit
and Sensor Pad if product is to be stored for an extended period of time.
Dispose of batteries according to your local ordinances. The Button cell
battery represents a small part and a choking hazard. ALWAYS keep all
batteries away from children.
10. IMPORTANT SAFETY INSTRUCTIONS
10.1 Heed all warnings – All warnings on the product and in the operating
instructions should be adhered to.
10.2 Follow all instructions – All operating and use instructions should
be followed.
10.3 Water and moisture - DO NOT use this apparatus near water. For
example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
environment or near a swimming pool and the like. Care should be taken
so that objects DO NOT fall onto units and that liquids are not spilled into
either unit or Sensor Pad through its openings.
10.4 Cleaning - Disconnect all units before cleaning. DO NOT immerse in
water any part of the monitor. Clean only with dry cloth.
10.5 Ventilation - DO NOT block any ventilation openings. Allow for proper
ventilation when units are in use. DO NOT cover the Nursery Unit with any
object such as a blanket. DO NOT place it in a drawer or in any location
which would muffle the sound or interfere with the normal flow of air.
10.6 Heat sources - DO NOT install near any heat sources such as radiators,
heat registers, stoves, TVs or other apparatus (including amplifiers) that
produce heat. Heat can damage the case or electrical parts.
10.7 Accessories - Only use attachments accessories specified by the
manufacturer. DO NOT place this product on an unstable cart, stand,
tripod, bracket or table. The product may fall, causing serious injury to
a child or adult and serious damage to the product. Use ONLY with a
cart, stand, tripod, bracket or table recommended by the manufacturer
or sold with the product. Any mounting of the product should follow the
manufacturer’s instructions.
10.8 Servicing - DO NOT attempt to service this product yourself as opening
or removing covers (except battery door) may expose you to dangerous
voltage or other hazards.
10.9 Replacement parts - When replacement parts are required, be sure
the replacement parts specified by the manufacturer have the same
characteristic as the original part. Unauthorized substitution may result
in fire, electric shock or other hazards.
10.10 Usage - This baby monitor is intended as an aid. It is NOT a substitute
for responsible and proper adult supervision and should not be used as such.
Use this appliance ONLY for its intended use as described in this manual.
10.11 Object and Liquid Entry - NEVER push objects of any kind into this
product through casing slots as they may touch dangerous voltage points
or short out parts that could result in a risk of fire or electric shock. NEVER
spill liquid of any kind on the product.
10.12 Vibration Source - When the Sensor Pad is in use, DO NOT use
a bedside crib, cot mobile or other cot accessories that may produce
vibrations. Other sources of vibrations may include fans, washing
machines, loud music, etc. These sources of vibration may interfere with
the performance of your Angelcare®monitor and the alarm will not sound
if it continues to detect any movement other than your baby’s. Be sure all
vibration sources are eliminated before using the monitor.
10.13 You may experience false alarms for several reasons. The
most common reason is the Nursery Unit has not been turned OFF
after you have removed your baby from the cot. Another reason is
the Sensor Pad has not been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm surface with the Angelcare®logo
side facing up. The sensitivity level may also need to be adjusted. Refer
to Step 4.3. Always be sure to immediately check on baby whenever an
alarm sounds.
10.14 Sensor Pad - Your Sensor Pad can be used in any cot that is stationary.
If the cot has a spring or slat base, place a hard board between the cot base
and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick. Only
use your Angelcare®monitor in a stationary sleeping environment such
as a cot where the Sensor Pad can rest on a completely flat, firm surface.
The Sensor Pad is made of plastic and does not permit the air to circulate.
Therefore, mildew build up could develop underneath the mattress in the Sensor
Pad area. We suggest rotating the mattress regularly to prevent any mildew.
11. IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES
11.1 Use ONLY the type and size of battery specified in the owner’s manual.
There is a risk of explosion if battery is replaced with an incorrect type.
11.2 DO NOT use rechargeable batteries in the Nursery Unit. Use alkaline
ba t te r ies ONLY.
11.3 DO NOT dispose batteries in fire. They may explode. Check with local
regulations for possible special disposal instructions.
11.4 Exercise care in handling batteries in order not to short out the batteries
with conducting materials such as rings, bracelets and keys. Overcharging,
short circuiting, reverse charging, mutilation, or incineration of batteries
must be avoided to prevent one or more of the following occurrences:
release of toxic materials, release of hydrogen and/or oxygen, gas and
rise in surface temperature.
11.5 DO NOT attempt to rejuvenate the battery provided with or identified
for use with this product by heating them. Sudden release of battery
electrolyte may occur, causing burns or irritation to eyes or skin.
11.6 If and when necessary, the battery must be replaced with identical
new ones or equivalent (volts and size).
11.7 Reverse polarity installation of the batteries in the end product must
be avoided. Reverse insertion of batteries can cause charging, and that
may result in leakage or explosion.
11.8 Remove the battery from this product if you store the product over 30
days because the battery could leak and damage the product.
11.9 Discard ‘dead’ batteries as soon as possible since ‘dead’ batteries are
more likely to leak in a product. If a battery has leaked or vented, it should
be replaced immediately using protective gloves.
11.10 DO NOT store this product, or the battery provided with or identified
for use with this product, in high-temperature areas.
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING & USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH OR DAMAGES TO
THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS,
CHILDREN OR INFANTS OLDER THAN 24 MONTHS.
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE
IF BABY IS OUT OF THE COT.
WARNING
Adult assembly required.
Keep small parts away from children when assembling.
We, at Angelcare®, stand behind all of our products.
If you are not completely satisfied or have any questions,
United States and Canada: Please contact us at:
[e-mail]
Other countries: Please contact your local distributor.
WARNINGS
2
01mf6A_Manuel_AC017_UK_12643.indd 2 18-01-24 14:37

Model AC017
Movement Monitor
SETUP REQUIREMENTS
INCLUDED:
Nursery Unit Tabletop stand
(for Nursery Unit)
Wireless movement
Sensor Pad
* Always place Angelcare®
logo side up *
CR3032 battery
(for Sensor Pad)
Miniature Philips
Screwdriver
2 AAA Alkaline
Batteries
2X
WHAT YOU WILL NEED (NOT INCLUDED):
STEP 1 - SETTING UP THE NURSERY UNIT
NURSERY UNIT:
Power ON/OFF Light Indicator
Low Battery Light Indicator
Battery Door
(2 AAA)
Power
ON/OFF
Pause/Pairing
Button
Nursery Unit Stand
Movement
Sensor Pad
Sensitivity
Switch
Sensor Pad
light indicator
1.1 - INSERT THE BATTERIES
When using the Nursery Unit for the first time, you will need to insert 2 AAA alkaline
batteries (not included).
3
E
N
01mf6A_Manuel_AC017_UK_12643.indd 3 18-01-24 14:37

1) Remove the battery door with
screwdriver and insert 2 AAA
alkaline batteries.
1.2 - SELECT A LOCATION FOR THE NURSERY UNIT
Nursery Unit can be installed using the tabletop stand.
Place the
Nursery Unit at
least 1 metre
from the cot
STEP 2 - POSITIONING THE MOVEMENT SENSOR PAD
2.1 - POWERING THE MOVEMENT SENSOR PAD
When using the Sensor Pad for the first time, you will need to insert the provided
CR3032 battery.
1) Remove the battery cover using a coin.
Turn in the direction of the arrow.
2) Place the included battery (CR3032) in
the compartment. Note: The + symbol
should be facing up.
3) Replace the battery cover (the two
dots will line up). The Sensor Pad is
now ON.
2.2 - INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT
IMPORTANT
If your cot does not have a solid, stable surface for the Sensor Pad, you will
need to place a support under it, to ensure correct operation of the system.
This hardboard support should be at least 6 mm thick and should have
minimum dimensions of 33 cm x 33 cm. This support board must be larger
than the Sensor Pad surface area.
The Sensor Pad functions with any size and type of mattress except
memory-foam mattresses, hollow frame mattresses and water beds. The
hardboard maintains a constant pressure on the Sensor Pad, enabling it to
detect the baby’s movements even when the baby is at the edges of the cot.
Hardboard
Sensor Pad
21) Remove the mattress from the cot.
2) Place the Sensor Pad - Angelcare®logo
side up - in the center of the mattress.
It should be centered on the hardboard
if your cot requires a hardboard
support.
3) Replace the mattress.
4
01mf6A_Manuel_AC017_UK_12643.indd 4 18-01-24 14:37

WARNING
• The Sensor Pad is not designed for use with adults, children or infants
older than 24 months.
• Discontinue used of the Sensor Pad when baby is older than 24 months.
Remove Sensor Pad from cot and store for future use.
• BEFORE FIRST TIME USE: To test that the unit is ready for use, refer to instruction
manual on how to test that the installation has been done correctly.
STEP 3 - TURNING ON YOUR MONITOR
Press and hold the Nursery
Unit ON/OFF button for 2
seconds until the Nursery
Unit Indicator flashes
slowly in green.
The Nursery Unit will emit a
sound and flash blue to
confirm pairing with the
Sensor Pad
NOTE:
If the green light does not appear
but the red light is flashing; or if
there are false alarms, adjust the
sensitivity level (Step 4.3).
STEP 4 - GETTING TO KNOW YOUR MONITOR
4.1 TESTING THE SENSOR PAD:
12
3
1) Move your hand lightly on the
mattress.
2) Remove your hand from the
mattress. After 15 seconds you will
hear a pre-alarm sound and the
light will flash red.
3) 5 seconds later the Nursery Unit will
emit loud continuous beeps and the
light will flash red continuously - this
is the movement alarm.
MOVEMENT ALARM
• If NO movement is detected after 15 seconds
you will hear a single pre-alarm sound from the
Nursery Unit.
• If after a further 5 seconds there is still NO
movement detected, Nursery Unit speakers will emit
loud continuous beeps - this is the movement alarm.
IF THE ALARM DOES NOT SOUND
• Avoid contact with cot while Sensor Pad
is in operation.
• Place cot near a supporting wall.
• Adjust Sensor Pad sensitivity level.
• Turn OFF cot mobile, fans, loud music or
anything else that may cause vibration.
TO STOP THE ALARM
Place your hand
back on the
mattress.
Press Pause
on the Nursery
Unit
OR
5
E
N
01mf6A_Manuel_AC017_UK_12643.indd 5 18-01-24 14:37

IMPORTANT
• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.
4.2 PAUSING AND RESTARTING THE SENSOR PAD:
Allows you to pause the Sensor Pad if you remove baby from the cot,
e.g. for feeding or comforting.
2
11) From the Nursery Unit, press the Pause button on the top
right of the unit.
2) The light will flash white when the Sensor Pad is paused.
The Nursery Unit will emit a single beep every 20 seconds
to indicate movement function is paused.
3) To unpause the Sensor Pad press the Pause button again.
IMPORTANT
• If you do not pause the Sensor Pad, the alarm will sound if there is no movement
detected on the surface of baby’s mattress after 20 seconds.
• Ensure to unpause the Sensor Pad before putting baby back in the cot.
4.3 - TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL:
To ensure adequate monitoring of your baby’s movements, you can adjust the sensitivity of the
Sensor Pad. Set a high sensitivity for a newborn and a lower sensitivity as baby grows and gains
weight. A thicker mattress will also need a higher sensitivity.
Slide the Nursery Unit sensitivity level button to select between low, medium or high level.
For optimal results begin with the preset
sensitivity level and only increase/decrease
if required.
IMPORTANT
• The Sensor Pad is not designed for use with adults, children or infants older than
24 months.
• Once you are finished using the Sensor Pad, please deactivate the Movement
Function and then remove it from the baby’s cot and store it away.
4.4 - BATTERIES
NURSERY UNIT LOW BATTERY INDICATOR:
The low battery yellow light indicator will flash and
an alarm will sound every 20 seconds when the
batteries on the Nursery Unit need to be replaced.
SENSOR PAD LOW BATTERY INDICATOR:
The low battery yellow light Indicator will flash and
an alarm will sound every 20 seconds when the
battery on the Sensor Pad needs to be replaced.
6
01mf6A_Manuel_AC017_UK_12643.indd 6 18-01-24 14:37

TROUBLESHOOTING
Power ON/OFF Light Indicator
Low Battery Light Indicator
Flashing green Monitor is activated
Flashing yellow Nursery Unit batteries are low
Sensor Pad Light Indicator
Flashing red No movement is detected or
Sensor Pad lost connectivity
Flashing white Monitor is paused
Flashing yellow Sensor Pad battery is low
FALSE ALARMS
• Turn OFF the Nursery Unit.
• Make sure there is no bedding between the mattress and the Sensor Pad.
• If the cot has a spring or slat base, place a hardboard between the crib base and the
Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure Sensor Pad is positioned as described under the setup requirements. Sensitivity may need to
be adjusted (refer to Step 4.3).
• Re-connect the Sensor Pad and Nursery Unit by pressing and holding the Nursery Unit Pairing button for
2 seconds until the blue light flashes and you hear a beep.
ALARM WILL NOT SOUND
• Avoid contact with the cot when the monitor is ON.
• Place cot near a solid supporting wall to avoid Sensor Pad from detecting movement
from outside the cot.
• Turn OFF cot mobile, fans, loud music or anything else that may cause vibration.
• You may need to decrease the sensitivity (refer to Step 4.3).
SENSOR PAD LIGHT INDICATOR FLASHING RED
• Make sure there is no bedding between the mattress and the Sensor Pad.
• The Sensor Pad must rest on a completely flat and firm surface. If the cot has a spring or slat base, place
a hard board between the cot base and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure Sensor Pad is positioned as described under the setup requirements. Sensitivity may need to
be adjusted (refer to Step 4.3).
LOSS OF CONNECTIVITY (NURSERY UNIT BLUE LIGHT FLASHES AND
EMITS A BEEP EVERY 20 SECONDS)
• Bring the units closer together.
• Press and hold for 2 seconds the Nursery Unit Pairing button, the Nursery Unit will emit a beep and will
flash blue to confirm connectivity.
NO POWER
• Check or replace batteries.
• Make sure monitor is ON.
7
E
N
01mf6A_Manuel_AC017_UK_12643.indd 7 18-01-24 14:37

IM017-UK-024012918
www.angelcarebaby.com
For assistance, FAQs or guidance with your monitor please visit
our Customer Support page at Angelcare.co.uk
LIMITED WARRANTY
Angelcare®warrants to the original owner of this product that Angelcare®
monitor is free from any material and workmanship defects for the term of the
warranty period (see warranty table below to determine the warranty for your
country). If this monitoring system fails to function properly when used as
directed under normal conditions and during the warranty period, Angelcare®
will either repair or replace the product, at our discretion, free of charge. Please
contact your local distributor to validate warranty and warranty period.
The product must be accompanied by a proof of purchase, either a bill of
sale or other proof that the monitoring system is within the warranty period.
Angelcare®will bear the cost of repairing or replacing the product and
shipping it back to you.
This warranty does not apply to a product which has been damaged as a
result of improper maintenance, an accident, improper voltage supply or
any other form of misuse. The warranty is also void if the owner repairs or
modifies the product in any way. Angelcare®is not liable for any incidental
or consequential damages with regard to this product. The warranty also
excludes any liability other than what is stated above. No other warranty
is given.
This warranty does not cover products and accessories which are not
Angelcare®-branded, or any problems that result from usage that is not
in accordance with product instructions, failure to follow the product
instructions, or problems caused by using accessories, parts or components
not supplied by Angelcare®.
LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT
APPLY TO YOU.
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING
FROM THE USE OF THIS PRODUCT.
IMPORTANT! This Angelcare®monitor is a personal care product. Please
do not return this product to the store. If you have questions or need help,
please call your distributor before returning this product:
international.angelcarebaby.com
TECHNICAL SPECIFICATIONS
Range:
Open field (Open area without obstructions):
up to 8 meters.
Power Supply:
2 AAA alkaline batteries for Nursery Unit
(not included)
1 CR3032 3V battery for Wireless Sensor Pad (included)
Caution: To reduce the risk of electric shock, do not expose this product to
rain or moisture.
Danger of explosion if batteries are incorrectly replaced. The battery for
the Sensor Pad is a user replaceable Lithium (not Li-Ion) battery and is NOT
rechargeable. Only use the Angelcare®recommended replacement battery.
To obtain information on replacement batteries please contact Angelcare®
customer service: www.angelcarebaby.com or contact your local distributor.
Instructions will be included with the replacement battery. Keep all batteries
away from children.
PROTECT THE ENVIRONMENT
The wheelie bin symbols mean that according to local laws and
regulations your product and/or its battery shall be disposed of
separately from household waste. When the product/battery reaches its
end of life take it to a collection point designated by local authorities.
The seperate disposal and recycling will help conserve natural resources
and protect human health and the environment. Refer to User’s Guide for
removal of batteries.
Batteries:
• DO NOT mix old and new batteries.
• DO NOT mix alkaline standard
(carbon-zinc), or rechargeable
(NI-CD, NIMH, etc.) batteries.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE.
Transmission:
Data transmission between the Nursery Unit and the Sensor Pad is made on
2.402 to 2.480 GHz frequency.
Maximum RF Power Transmitted: 4dBm (2.5mW)
Hereby, Angelcare®Monitors Inc., declares this baby monitor is in
compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address:
www.angelcarebaby.com/declaration-of-conformity
WARRANTY TERM PER COUNTRY
UK, South Africa, Russia 1 year
Other countries 2 years
01mf6A_Manuel_AC017_UK_12643.indd 8 18-01-24 14:37