Angstrom MoneyChecker 6700 User manual

®
Universal Model
6700
Industrial Model
6500
859.282.0020 • www.angtech.com
It Out...
McDonald’s
BurgerKing
WhiteCastle
Banks
CreditUnions
Wendy’s
ConvenientStores
RetailOutlets
All Are Protected
by
oneyChecker
®
oneyChecker
oneyChecker
®
oneyChecker
oneyChecker
Not only are these pens easily lost, but in 2000 the
Secret Service estimated the Counterfeit Security
Pen to have an 83% FAILURE rate. They have proven
to be extremely UNRELIABLE. Many chemicals affect
this pen including: Soap, bleach, battery acid, wax,
grease or even hairspray. It is impossible for this pen
to verify the hardest to counterfeit security features
in currency, such as the fluorescent security threads
and watermarks. The MoneyChecker from Angstrom
Technologies verifes these security features.
The Universal Model 6700 Advantage
Both MoneyChecker models verify security features
in US currency, but the additional UV lamp in the
hood of the 6700 Universal model also verifes
security features in many other items, such as:
•CREDIT CARDS: Hidden ultraviolet security
features only visible under the UV lamp.
•CHECKS: Made of Secure paper; will absorb the
UV light and will not glow, but may have security
markings that can only be seen under UV light.
•TRAVELER’S CHECKS: May appear dull if
genuine, fluorescent signature lines, watermarks.
•INTERNATIONAL CURRENCY: Security
threads, holograms, and watermarks.
•STATE ISSUED DRIVER’S LICENSES:
UV properties built in will vary from state to state.
•RESIDENT ALIEN/GREEN CARDS:
“USA” or an image of the US Flag will fluoresce
throughout the card when placed under the UV light
•PASSPORTS: Various unseen multi-colored UV
fluorescent emblems and images, will vary by
country
•EVENT TICKETS: Various ultraviolet and UV
security features
•OTHER ITEMS: US Govt. checks, Cashier’s
Checks, and many more
The MoneyChecker®
Has Got You Covered
®
Counterfeit Security Pen?!
OPERATION INSTRUCTIONS
No Business Can Afford to
be left UNPROTECTED
7880 Foundation Drive
Florence KY 41042

Operation Instructions
1. Universal Model 6700 only: Plug the power cord from
the hood into the jack located on the rear of the unit.
2. Plug the power supply adapter into the input jack on
the right side of the unit.
3. Activate the unit by passing an item (currency or other
suitable target) over the sensor located near the front
right corner of the template.
4. Power saving feature: the unit will turn off after
3 to 4 minutes when not in use. It will remain off
until another target is passed over the sensor.
5. Make sure no debris collects in the sensor slot, this
can disable the unit. Debris can be removed with a dry
toothbrush, compressed air, etc. Do not insert sharp or
metallic objects into the sensor.
6. There is no on/off switch, unplug the unit when not in
use for long periods of time.
Verifying Security Features in US Currency:
1. The UV and LED lights are designed to illuminate
the security thread and watermark embedded in US
currency after 1996. Older bills may not contain these
features.
2. Place the bill over the template, portrait side up.
3. The security thread will glow a specifc color depending
upon the denomination of the currency. The template
shows the location and color of the security thread for
each denomination.
4. Note: In 2004, the $50 thread was moved to the left
approx. ½ inch. In 2008, the $5 thread was moved from
the left to the right side of Lincoln’s portrait. See the
“Security Thread Features” section.
5. The LED light on the right side of the unit is used to
verify the presence of the watermark. In most cases,
the watermark should match the portrait on the bill.
Note: the watermark in the $5 bill released in 2008 is
the numeral “5”.
Additional information regarding US currency security
features can be found on the following websites:
www.moneyfactory.gov
www.secretservice.gov/know_your_money.shtml
Security Thread Features
$100
1996-
RED (Pink)
On the left
of the portrait
YELLOW
On the right of
the portrait
moved 1/2’’
$20
All versions
2000-
GREEN
On the left of
the portrait
$10
All versions
2000-2008
ORANGE
On the right of
the portrait
$5
2000-2008
BLUE
On the left
of the portrait
2008-
BLUE
On the right of
the portrait
$50
1997-2004
YELLOW
On the right of
the portrait
UV Lamp Replacement Instructions
• All models have one UV lamp (black light) in the bottom
(part number 6013).
• The Universal Model 6700 has an additional UV lamp
in the hood (part number 6015-J).
• Replacement UV lamps can be ordered from your
distributor or purchased directly from Angstrom
Technologies.
Note: the watermark LED lamp should last the life of the unit and is not
user replaceable.
Top Lamp Replacement:
Universal Model 6700 Only
(part no. 6015-J)
1. To change the top UV lamp, replace the entire hood
assembly.
2. Warning: High Voltage - make sure the power supply is
disconnected from the side of the unit before proceeding.
3. Unplug the hood from the rear of the unit.
4. Remove the two screws holding the hood to the base.
5. Re-assemble the unit with the new hood assembly:
route the lamp power cord through the notch in the rear
of the hood and screw the hood to the base.
6. Plug the new hood into the jack on the rear of the unit.
Bottom Lamp Replacement: All Models
(Part no. 6013)
1.Warning: High Voltage -make sure the power supply is
disconnected from the side of the unit before proceeding.
2. For the Universal 6700 model, follow steps 2-4 above
to remove the hood assembly.
3. For the Industrial 6500 model, slide the hood toward
the rear of the unit and lift.
4. Remove the small screw located in the upper left
corner of the template.
5. Push the tabs on the right and left side of the cover
towards each other and lift off the clear plastic cover and
the template to expose the UV bulb housing.
6. Pull back on the two black retaining clips in front of the
lamp assembly and remove the lamp assembly.
7. Install the new lamp. The lamp assembly has three tabs
that are held by three retaining clips; insert the single tab
into the rear retaining clip first, then gently press the front
of the lamp assembly so that the two remaining tabs snap
into the front retaining clips .
8. Re-assemble the unit.
2000-
2004-
7. Warning: High Voltage- Do not submerge or expose
the unit to liquids. Always disconnect the power
before replacing lamps.